ATOMI specifications overview table - Revision history

Esa at 12:09, 11 July 2017

2017-07-11T12:09:26Z

Esa at 11:52, 7 June 2017

2017-06-07T11:52:24Z

Esa at 10:42, 2 June 2017

2017-06-02T10:42:19Z

Esa at 10:40, 2 June 2017

2017-06-02T10:40:37Z

Esa: Created page with "{| class="wikitable" |- ! Function !! Description |- | Servo/stepping motor drive || Closed loop control of various types of servo motors by sinusoidal field o..."

2017-06-02T10:26:21Z

Created page with "{| class="wikitable" |- ! Function !! Description |- | Servo/stepping motor drive || Closed loop control of various types of servo motors by sinusoidal field o..."

New page

{| class="wikitable"
|-
! Function !! Description
|-
| Servo/stepping motor drive || Closed loop control of various [[Motor types|types of servo motors]] by sinusoidal field oriented control with [[Dead-time distortion|dead-time distortion correction]] and [[high dynamic range torque control]].
*Synchronous AC & BLDC motors
**Sinusoidal and trapezoidal commutated
**SPM (Surface Permanent Magnet) and IPM (Internal Permanent Magnet) types
*Brush DC motors
*Linear motors
**Iron core
**Ironless (with external inductive filter)
*Stepping motor, 2 phase (4,6 or 8 wires)
|-
| [[Control modes]] ||
* Torque control
*Velocity/speed control
*Position control
|-
| [[Setpoint]] types||
See [[IONI specifications#Setpoint_signal_.2F_reference_inputs|setpoint signal / reference inputs]] list
*Direct set-point tracking via [[pulse and direction]], [[PWM]], [[Analog setpoint|Analog]], [[Quadrature]], [[SimpleMotion V2]]
*[[Pulse burst positioning]]
*Buffered synchronous motion commands via [[SimpleMotion V2]]
|-
| Closed loop || Cascaded control loops (PIV):
*Torque / current control, update frequency 20.0 kHz
*Velocity control, update frequency 2.5 kHz
*Position control, update frequency 2.5 kHz
|-
| [[Feed-forward]]s || Feed-forwards working in velocity & position control modes:
*Acceleration (inertia canceling) feed-forward
*Velocity (friction canceling) feed-forward
|-
| [[Homing]] || Integrated homing function for position control mode:
*Sensorless [[hard-stop homing]]
*Home switch search
*Index pulse search
*Soft position limits (eliminate limit switches)
|-
| [[Feedback devices]] || See [[IONI specifications#Feedback_devices|feedback devices]] list
|-
| Safety ||
*[[Safe torque off]] with 3-way redundancy
*[[Charge pump enable input]]
*Stopping motor on errors
**Tracking error (velocity & position)
**Over speed error
**Limit switch
*DC motor runaway prevention on feedback loss
*Communication error detection
|-
| Protections ||
*Over current
*Short circuit (phase-to-phase)
*I2t motor thermal protection
*Over & under voltage
*Over temperature
|-
| Power supply||
*Externally supplied
**IONI, IONI Pro 5 – 52 VDC
**IONI Pro HC 5 - 55 VDC
*Additionally an external 5 VDC logic supply required. ''Note: if drive is used with [[IONICUBE]] motherboards, then 24 VDC logic supply voltage is needed instead as IONICUBE has on-board 5V regulator.''

|-
| Motor output current1||
* AC/BLDC/Stepping/Linear motors (current specified as [[Peak value of sine|peak of sine]]):
**IONI 0-15 A
**IONI Pro 0-18 A
**IONI Pro HC 0-25 A
* Brush DC motors:
**IONI 0-19.5 A
**IONI Pro 0-23.4 A
**IONI Pro HC 0-30 A
|-
| Commissioning||
*[[Granity]] setup software
* [[IONI & IONICUBE user guide|Online user guide]]
|-
| Compliance || CE (LVD & EMC): EN 61800-5-1:2007, IEC 61000-6-1:2005 and IEC 61000-6-3:2006.
SIL2: IEC 61800-5-2:2016-04

Notes:
* The device is Low Voltage Directive (LVD) compliant up to 42 VDC power supply, and above that level the supply voltage is considered hazardous, so external measures (such as or isolation or protective impedance) are necessary to prevent human contact to any circuit connected to the device.
* In order to meet EMC standard requirements, a proper installation and wiring is necessary. Refer to user guide for proper installation.
|-
|Reliability
|
* MTBF: 2.99 million hours
* Failure rate (all delivered units, actual statistic from 2015-2017): 0.36%
|}
1) Currents achievable continuously only with with sufficient coolant air flow. Without forced cooling, typically 30-45% of the maximum range can be driven continuously. Despite of this, maximum current is available for short periods of time even without cooling. Current is automatically throttled on temperature rise to protect the drive.

[[Category:Work_in_progress_pages]]

@@ Line 79: / Line 79: @@
 |Reliability
+|
-* MTBF: TBD
+* MTBF: 660000 hours
 |}
 <sup>1</sup>) Currents achievable continuously only with with sufficient coolant air flow. Without forced cooling, typically 30-45% of the maximum range can be driven continuously. Despite of this, maximum current is available for short periods of time even without cooling. Current is automatically throttled on temperature rise to protect the drive.
 [[Category:Work_in_progress_pages]]

@@ Line 71: / Line 71: @@
 | Commissioning||
 *[[Granity]] setup software
 |-
 | Compliance || CE (LVD & EMC): EN 61800-5-1:2007, IEC 61000-6-1:2005 and IEC 61000-6-3:2006.

@@ Line 20: / Line 20: @@
 | [[Setpoint]] types||
 See [[IONI specifications#Setpoint_signal_.2F_reference_inputs|setpoint signal / reference inputs]] list
-*Direct set-point tracking via [[pulse and direction]], [[PWM]], [[Analog setpoint|Analog]], [[Quadrature]], [[SimpleMotion V2]]
+*Direct set-point tracking via [[pulse and direction]], [[PWM]], [[Analog setpoint|Analog]], and [[SimpleMotion V2]]
-*[[Pulse burst positioning]]
 *Buffered synchronous motion commands via [[SimpleMotion V2]]
 |-
@@ Line 39: / Line 38: @@
 *Soft position limits (eliminate limit switches)
 |-
-| [[Feedback devices]] || See [[IONI specifications#Feedback_devices|feedback devices]] list
+| [[Feedback devices]] ||
 |-
 | Safety ||
@@ Line 59: / Line 59: @@
 |-
 | Power supply||
-*Externally supplied
+*Externally supplied 12 – 49 VDC
-**IONI, IONI Pro 5 – 52 VDC
+*Single power supply operation mode, no separate power supply needed for logic
-**IONI Pro HC 5 - 55 VDC
-*Additionally an external 5 VDC logic supply required. ''Note: if drive is used with [[IONICUBE]] motherboards, then 24 VDC logic supply voltage is needed instead as IONICUBE has on-board 5V regulator.''
 |-
-| Motor output current<sup>1</sup>||
+| Motor output current <sup>1</sup>||
 * AC/BLDC/Stepping/Linear motors (current specified as [[Peak value of sine|peak of sine]]):
-**IONI 0-15 A
+**0 - 8 A
-**IONI Pro 0-18 A
-**IONI Pro HC 0-25 A
 * Brush DC motors:
-**IONI 0-19.5 A
+**0 - 10 A
-**IONI Pro 0-23.4 A
-**IONI Pro HC 0-30 A
 |-
 | Commissioning||
@@ Line 80: / Line 74: @@
 |-
 | Compliance || CE (LVD & EMC): EN 61800-5-1:2007, IEC 61000-6-1:2005 and IEC 61000-6-3:2006.
-SIL2: IEC 61800-5-2:2016-04
+Notes:
-−
 Notes:
 * The device is Low Voltage Directive (LVD) compliant up to 42 VDC power supply, and above that level the supply voltage is considered hazardous, so external measures (such as or isolation or protective impedance) are necessary to prevent human contact to any circuit connected to the device.
 * In order to meet EMC standard requirements, a proper installation and wiring is necessary. Refer to user guide for proper installation.
@@ Line 88: / Line 80: @@
 |Reliability
+|
-* MTBF: 2.99 million hours
+* MTBF: TBD
-* Failure rate (all delivered units, actual statistic from 2015-2017): 0.36%
 |}
 <sup>1</sup>) Currents achievable continuously only with with sufficient coolant air flow. Without forced cooling, typically 30-45% of the maximum range can be driven continuously. Despite of this, maximum current is available for short periods of time even without cooling. Current is automatically throttled on temperature rise to protect the drive.
 [[Category:Work_in_progress_pages]]