Argon user guide/J4 connector wiring - Revision history

Tero K: /* Wiring multiple drives with power supply & braking resistor sharing */

2013-10-25T10:59:52Z

‎Wiring multiple drives with power supply & braking resistor sharing

Tero K: /* Wiring multiple drives with power supply & braking resistor sharing */

2013-10-21T12:54:18Z

‎Wiring multiple drives with power supply & braking resistor sharing

Tero K: /* Wiring multiple drives with power supply & braking resistor sharing */

2013-10-21T12:50:10Z

‎Wiring multiple drives with power supply & braking resistor sharing

Tero K: /* Connecting multiple drives with power supply & braking resistor sharing */

2013-09-26T22:20:20Z

‎Connecting multiple drives with power supply & braking resistor sharing

Tero K: /* J4 wiring guide */

2013-09-26T22:19:32Z

‎J4 wiring guide

Tero K: /* Pin-out */

2013-09-26T22:18:07Z

‎Pin-out

Tero K: /* Pin-out */

2013-09-03T21:56:16Z

‎Pin-out

Tero K: /* J4 wiring guide */

2013-08-18T19:51:33Z

‎J4 wiring guide

Tero K at 19:21, 18 August 2013

2013-08-18T19:21:45Z

Tero K: Created page with "J4 is a 10 pole terminal block connector for several functions: earthing, AC power input, motor output, regenerative resistor output and HV DC link sharing. See also the main ..."

2013-08-18T18:59:33Z

Created page with "J4 is a 10 pole terminal block connector for several functions: earthing, AC power input, motor output, regenerative resistor output and HV DC link sharing. See also the main ..."

New page

J4 is a 10 pole terminal block connector for several functions: earthing, AC power input, motor output, regenerative resistor output and HV DC link sharing. See also the main article about [[Argon user guide/Wiring|Argon wiring]].

{{electricshock|Dangerous & non-isolated mains potential voltages are present in the connector J4! Keep away from this connector and its wiring when drive has been powered recently. Carefully read the page [[Power supply safe discharging]] before operating.}}
==Pin-out==
{| class="wikitable"
|-
! Pin #||Pin name !! Descrpition !! AC/BLDC motor connection || Brush DC motor connection
|-
| 1||VN || HV DC link negative rail || colspan=2| Do not connect
|-
| 2||BR || Braking resistor output || colspan=2 rowspan=2|Optional braking resistor terminals. See [[Argon braking resistor]]
|-
| 3||VP || HV DC link positive rail
|-
| 4||PE ⏚ || Protective earth || colspan=2|Connect to motor PE conductor and motor cable shield
|-
| 5||U || Motor phase output || Motor U phase ¹ || Motor armature+
|-
| 6||V || Motor phase output || Motor V phase ¹ || Motor armature-
|-
| 7||W || Motor phase output || Motor W phase ¹ || No connection
|-
| 8||L || AC mains supply Line || colspan=2|Connect to AC supply line
|-
| 9||N || AC mains supply Neutral || colspan=2|Connect to AC supply neutral
|-
| 10||PE ⏚ || Protective earth || colspan=2|Connect to supply protective earth. <span style="color:#cc0000">This connection is always mandatory when any voltage larger than 30 VAC or 42 VDC is supplied to the device!</span>
|}
¹ In some motors U,V,W phases are called R,S,T instead.
==J4 wiring guide==
Basic wiring scheme of Argon (servo drive). Use of shielded cables is optional but highly recommended for EMI compliance and optimal reliability. For recommended accessories (EMI filters etc, see [[Argon user guide/Mating connectors and accessories|Mating connectors and accessories]].

[[File:Argonwiringoverview.png|800px]]

[[category:Argon wiring]]

@@ Line 32: / Line 32: @@
 ===Wiring multiple drives with power supply & braking resistor sharing===
 Note this drawing does not include wiring to motor (J4), motor brake (J3), feedback device (J1), controller (J5) and AC power input circuity.
-{{caution|Using HV DC bus sharing via VP and VN terminals or supplying external DC voltage to them, renders the [[safe torque off]] STO1 input unusable because STO1 is based on by cutting the AC supply. In order to preserve STO1 functionality with DC bus sharing, the STO1 signal must be fed simultaneously to all DC bus sharing drives. If an external DC supply is used (no AC input to L & N), then STO1 will not operate.}}
+{{caution|Using HV DC bus sharing via VP and VN terminals or supplying external DC voltage to them, renders the [[safe torque off]] STO1 input unusable because STO1 is based on by cutting the AC supply. In order to preserve STO1 functionality with DC bus sharing, the STO1 signal must be fed simultaneously to all DC bus sharing drives. If an external DC supply is used (no AC input to L & N), then STO1 will not operate.<br/><br/>STO1 will also be inoperable if DC voltage is supplied to L & N inputs instead of AC. With DC supply, STO1 ibput must be always powered as the internal relay may damage if STO1 used with DC supply. }}
 [[File:Argon_wiring_multiple.png|800px]]

@@ Line 32: / Line 32: @@
 ===Wiring multiple drives with power supply & braking resistor sharing===
 Note this drawing does not include wiring to motor (J4), motor brake (J3), feedback device (J1), controller (J5) and AC power input circuity.
-{{caution|Using HV DC bus sharing via VP and VN terminals or supplying external DC voltage to them, renders the [[safe torque off]] STO1 input unusable. In order to preserve STO1 functionality with DC bus sharing, the STO1 signal must be fed simultaneously to all DC bus sharing drives. If an external DC supply is used (no AC input to L & N), then STO1 will not operate.}}
+{{caution|Using HV DC bus sharing via VP and VN terminals or supplying external DC voltage to them, renders the [[safe torque off]] STO1 input unusable because STO1 is based on by cutting the AC supply. In order to preserve STO1 functionality with DC bus sharing, the STO1 signal must be fed simultaneously to all DC bus sharing drives. If an external DC supply is used (no AC input to L & N), then STO1 will not operate.}}
 [[File:Argon_wiring_multiple.png|800px]]

@@ Line 32: / Line 32: @@
 ===Wiring multiple drives with power supply & braking resistor sharing===
 Note this drawing does not include wiring to motor (J4), motor brake (J3), feedback device (J1), controller (J5) and AC power input circuity.
 [[File:Argon_wiring_multiple.png|800px]]

@@ Line 30: / Line 30: @@
 ==J4 wiring guide==
-===Connecting multiple drives with power supply & braking resistor sharing ===
+===Wiring multiple drives with power supply & braking resistor sharing===
 Note this drawing does not include wiring to motor (J4), motor brake (J3), feedback device (J1), controller (J5) and AC power input circuity.
 [[File:Argon_wiring_multiple.png|800px]]
 ===Detailed single drive wiring schematics===
 Basic wiring scheme of Argon (servo drive). Use of shielded cables is optional but highly recommended for EMI compliance and optimal reliability. For recommended accessories, EMI filters etc, see [[Argon user guide/Mating connectors and accessories|Mating connectors and accessories]].

← Older revision		Revision as of 22:19, 26 September 2013
Line 30:		Line 30:

	==J4 wiring guide==		==J4 wiring guide==
		+	===Connecting multiple drives with power supply & braking resistor sharing ===
		+	Note this drawing does not include wiring to motor (J4), motor brake (J3), feedback device (J1), controller (J5) and AC power input circuity.
		+	[[File:Argon_wiring_multiple.png\|800px]]
		+	===Detailed single drive wiring schematics===
	Basic wiring scheme of Argon (servo drive). Use of shielded cables is optional but highly recommended for EMI compliance and optimal reliability. For recommended accessories, EMI filters etc, see [[Argon user guide/Mating connectors and accessories\|Mating connectors and accessories]].		Basic wiring scheme of Argon (servo drive). Use of shielded cables is optional but highly recommended for EMI compliance and optimal reliability. For recommended accessories, EMI filters etc, see [[Argon user guide/Mating connectors and accessories\|Mating connectors and accessories]].

@@ Line 7: / Line 7: @@
 ! Pin #||Pin name !! Descrpition !! AC/BLDC motor connection || Brush DC motor connection
 |-
-| 1||VN || HV DC link negative rail || colspan=2| Do not connect
+| 1||VN || HV DC link negative rail || colspan=2| Do not connect, unless linking multiple drives with VN & VP to share their internal power supplies and braking resistor.
 |-
 | 2||BR || Braking resistor output || colspan=2  rowspan=2|Optional braking resistor terminals. See [[Argon braking resistor]]

@@ Line 25: / Line 25: @@
 | 9||N || AC mains supply Neutral || colspan=2|Connect to AC supply neutral
 |-
-| 10||PE &#9178; || Protective earth || colspan=2|Connect to supply protective earth. <span style="color:#cc0000">This connection is always mandatory when any voltage larger than 30 VAC or 42 VDC is supplied to the device!</span>
+| 10||PE &#9178; || Protective earth || colspan=2|Connect to supply protective earth. <span style="color:#ee0000">This connection is always mandatory when any voltage larger than 30 VAC or 42 VDC is supplied to the device!</span>. See [[Argon user guide/Earthing]].
 |}
 ¹ In some motors U,V,W phases are called R,S,T instead.
 ==J4 wiring guide==
 Basic wiring scheme of Argon (servo drive). Use of shielded cables is optional but highly recommended for EMI compliance and optimal reliability. For recommended accessories, EMI filters etc, see [[Argon user guide/Mating connectors and accessories|Mating connectors and accessories]].

@@ Line 29: / Line 29: @@
 ¹ In some motors U,V,W phases are called R,S,T instead.
 ==J4 wiring guide==
-Basic wiring scheme of Argon (servo drive). Use of shielded cables is optional but highly recommended for EMI compliance and optimal reliability. For recommended accessories (EMI filters etc, see [[Argon user guide/Mating connectors and accessories|Mating connectors and accessories]].
+Basic wiring scheme of Argon (servo drive). Use of shielded cables is optional but highly recommended for EMI compliance and optimal reliability. For recommended accessories, EMI filters etc, see [[Argon user guide/Mating connectors and accessories|Mating connectors and accessories]].
 [[File:Argonwiringoverview.png|800px]]
 [[category:Argon wiring]]

← Older revision		Revision as of 19:21, 18 August 2013
Line 1:		Line 1:
−	J4 is a 10 pole terminal block connector for several functions: earthing, AC power input, motor output, regenerative resistor output and HV DC link sharing. See also the main article about [[Argon user guide/Wiring\|Argon wiring]].	+	{{SetAUGTitle\|J4 connector wiring}}{{ArgonManualNav}}J4 is a 10 pole terminal block connector for several functions: earthing, AC power input, motor output, regenerative resistor output and HV DC link sharing. See also the main article about [[Argon user guide/Wiring\|Argon wiring]].

	{{electricshock\|Dangerous & non-isolated mains potential voltages are present in the connector J4! Keep away from this connector and its wiring when drive has been powered recently. Carefully read the page [[Power supply safe discharging]] before operating.}}		{{electricshock\|Dangerous & non-isolated mains potential voltages are present in the connector J4! Keep away from this connector and its wiring when drive has been powered recently. Carefully read the page [[Power supply safe discharging]] before operating.}}