SimuCUBE hardware requirements - Revision history

Mtakala at 13:22, 28 February 2018

2018-02-28T13:22:33Z

Mtakala at 12:56, 28 February 2018

2018-02-28T12:56:59Z

Tero K at 12:07, 29 June 2016

2016-06-29T12:07:07Z

Tero K: Tero K moved page SimuCUBE user guide/List of things needed to SimuCUBE hardware requirements

2016-06-29T11:29:06Z

Tero K moved page SimuCUBE user guide/List of things needed to SimuCUBE hardware requirements

Tero K at 11:21, 29 June 2016

2016-06-29T11:21:12Z

Tero K at 22:49, 28 June 2016

2016-06-28T22:49:58Z

Tero K at 22:42, 28 June 2016

2016-06-28T22:42:20Z

86.114.147.102 at 12:19, 1 June 2016

2016-06-01T12:19:31Z

Tero K at 11:48, 30 May 2016

2016-05-30T11:48:13Z

Tero K: taulukko tehty

2016-05-30T11:45:02Z

taulukko tehty

@@ Line 44: / Line 44: @@
+|
 * [[MMos]] firmware (community sourced)
-* SimuCUBE open source firmware (work in progress, not usable yet)
+* SimuCUBE firmware [[SimuCUBE firmware releases]]
-|Until SimuCUBE official open source firmware is ready, it's recommended to use MMos firmware available from various internet sites/forums.
+|MMos firmware is available from various internet sites/forums.
 |}
 [[Category:SimuCUBE]]
 [[Category:SimuCUBE_user_guide]]

@@ Line 1: / Line 1: @@
 {{SimucubeManualNav}}List of required items for wiring and usage of SimuCUBE as force feedback controller.
 {| class="wikitable"
 !Item
@@ Line 48: / Line 48: @@
 |}
 [[Category:SimuCUBE]]

@@ Line 47: / Line 47: @@
 |Until SimuCUBE official open source firmware is ready, it's recommended to use MMos firmware available from various internet sites/forums.
 |}
 [[Category:SimuCUBE_user_guide]]
 [[Category:SimuCUBE]]

@@ Line 1: / Line 1: @@
-List of required items for wiring and usage of SimuCUBE as force feedback controller.
+{{SimucubeManualNav}}List of required items for wiring and usage of SimuCUBE as force feedback controller.
 {| class="wikitable"
 !Item
@@ Line 50: / Line 50: @@
 {{next|[[SimuCUBE_user_guide/Wiring_overview|Wiring]]}}
 [[Category:SimuCUBE_user_guide]]
 [[Category:SimuCUBE]]

@@ Line 27: / Line 27: @@
 |Servo motor
 |1
+|[[List of motors for SimuCUBE]]
 |Recommended at least 15 Nm peak torque for direct drive wheel applications. Check motor specifications the required current. IONI Pro HC can output 25 A (peak of sine) current, which equals 17.7 A RMS current (note that AC motor manufacturers typically give current rantings as RMS value).
 |-
 |Mini USB cables (from USB A to USB Mini B)
 |1-2
+|{{Digikey|1175-1053-ND}}
 |SimuCUBE has two Mini USB ports, one for USB HID (force feedback interface) and one for [[Granity]] connection. One cable is sufficient but requires swapping cable between the ports during configuration step. Two cables are recommended.
 |-

← Older revision	Revision as of 11:29, 29 June 2016
(No difference)

@@ Line 8: / Line 8: @@
 |SimuCUBE
 |1
-|https://granitedevices.com/store/applications/simulators.html
+|[https://granitedevices.com/store/applications/simulators.html Web store]
+|
 |-
 |IONI Pro or IONI Pro HC
 |1
-|https://granitedevices.com/store/applications/simulators.html
+|[https://granitedevices.com/store/applications/simulators.html Web store]
-|Decide drive model based on the required current to the motor. To compare IONI models, see [[IONI device model comparison]].
+|Decide drive model based on the required current to the motor. To compare IONI models, see [[IONI device model comparison]]. Suggestions:
 |-
 |24 to 48 VDC power supply, recommended 300 W minimum
@@ Line 20: / Line 22: @@
+|
 * [[List of 48V power supplies]]
-* https://granitedevices.com/store/applications/simulators.html
+* Power supplies at Granite Devices [https://granitedevices.com/store/applications/simulators.html Web store]
 |IONI drive has feature called "power consumption limit" which allows using also undersized power supplies without causing errors. However, if power consumption limit activates, then produced torque will be also reduced.
 |-
@@ Line 35: / Line 37: @@
 |15 pin (two row type) D-Sub male connector + connector hood (cover)
 |1
+|[[List of D-Sub 15 pin connector parts]]
 |This is the mating connector for encoder port of SimuCUBE, get these unless your motor comes with SimuCUBE/IONI/Argon compatible pre-made encoder cable.
 |-
@@ Line 41: / Line 43: @@
 |1
+|
-* MMos firmware (community sourced)
+* [[MMos]] firmware (community sourced)
 * SimuCUBE open source firmware (work in progress, not usable yet)
 |Until SimuCUBE official open source firmware is ready, it's recommended to use MMos firmware available from various internet sites/forums.