Difference between revisions of "EMI suppression cores"

From Granite Devices Knowledge Wiki
Jump to: navigation, search
[checked revision][checked revision]
(Usage)
 
(16 intermediate revisions by 3 users not shown)
Line 1: Line 1:
[[File:Ferrirebeads.jpg|thumb|Snap-on ferrite beads]]
+
[[File:Ferrirebeads.jpg|thumb|Snap-on ferrite cores]]
[[File:Ferritebead.jpg|thumb|Toroidal ferrite bead]]
+
[[File:Ferritebead.jpg|thumb|Toroidal ferrite core]]
EMI suppression cores a.k.a. '''ferrite beads''' are an efficient way to reduce high frequency interference from wiring. Adding ferrute beads to signal & power wiring is recommended if signal reliability problems are encountered.
+
EMI suppression cores or ferrite cores are an efficient way to reduce high frequency interference from wiring. Running cables through a ferrite cores is a recommended solution attempt if signal reliability or connection problems are encountered.
 
==Selection==
 
==Selection==
For motor control applications it is recommended to get low to medium frequency ferrite beads for maximum efficiency.  
+
For motor control applications it is recommended to get low to medium frequency ferrite cores for maximum efficiency.  
 
;Preferred types
 
;Preferred types
 
*Core material designed for low to medium frequency bands (attenuation between 1-300 MHz)
 
*Core material designed for low to medium frequency bands (attenuation between 1-300 MHz)
 
*Large enough to fit cable multiple rounds through it
 
*Large enough to fit cable multiple rounds through it
;Avoid
+
;Avoid (might make things worse)
 
*Core material designed for high frequency bands (above 300 MHz)
 
*Core material designed for high frequency bands (above 300 MHz)
*Inductor cores - will just add inductance and make things worse
+
*Inductor cores
 
*Iron powder cores
 
*Iron powder cores
 +
*Most ferrite & iron powder cores look same. If unsure about material properties, its most safe to purchase new low to medium frequency cores.
 +
 +
As example, take a look at [http://lairdtech.thomasnet.com/category/round-and-cylindrical-cores?&plpver=10 Laird broadband and low frequency cores].
 
==Where to find suitable cores==
 
==Where to find suitable cores==
Most ferrite & iron powder cores look same. So if unsure about material properties, its most safe bet to purchase low to medium frequency beads from distributors such as:
+
Ferrite cores are available from most electronic part distributors such as:
 
*Digikey
 
*Digikey
 
*Mouser
 
*Mouser
 
*Farnell
 
*Farnell
Some popular ferrite bead brands:
+
Some popular ferrite core brands:
 
* Laird-Signal Integrity Products
 
* Laird-Signal Integrity Products
 
* Fair-Rite
 
* Fair-Rite
==Usage with VSD-E/XE drives==
+
==Usage==
To solve an EMI problem its good to have selection of beads that can be tried on different cables. Most typical placement for beads:
+
===Application===
*USB adapter
+
[[File:Ferrite multiple turns.jpg|thumb|Turning cable 2-3 times through core or using multiple in series increases filtering performance.]]
*CMD cable
+
[[File:Argon test stup closeup m.jpg|thumb|Correct installation of a core in 3 phase motor U,W and V wires and leaving PE wire out.]]
*Encoder cable
+
Application tips:
*Motor output cable (all motor wires through core, multiple turns)
+
*If possible, make 2-3 turns of cable through one core to maximize it's effectiveness
*HV DC power supply cable (+ and - leads through core, multiple turns)
+
*Place core close to interference source, not in the middle of the cable
 +
 
 +
===With servo drives===
 +
To solve an EMI problem its good to have selection of cores that can be tried on different cables. Most typical placement for cores:
 +
*Motor output cable (all motor wires through core but '''not''' earth conductor). However, if earth conductor is hard to separate, then feeding all wires through core is still better than nothing.
 +
*High voltage power supply cable (+ and - leads through core)
 +
*USB adapter or other communication cables
 +
*Control I/O cables
 +
*Encoder/feedback device cable
 +
{{Tip| Don't run multiple different type of signals through single core. I.e. don't combine power supply and motor leads in one core. Doing so  can make filtering worse than without cores.}}
 +
 
 
==See also==
 
==See also==
 
*[[Wikipedia:Ferrite bead]]
 
*[[Wikipedia:Ferrite bead]]
[[Category:Troubleshooting]]
+
[[Category:Argon troubleshooting]]
[[Category:Setup guides]]
+
[[Category:IONI troubleshooting]]
 +
[[Category:VSD-E/XE troubleshooting]]
 +
[[Category:Glossary]]

Latest revision as of 12:32, 12 February 2016

Snap-on ferrite cores
Toroidal ferrite core

EMI suppression cores or ferrite cores are an efficient way to reduce high frequency interference from wiring. Running cables through a ferrite cores is a recommended solution attempt if signal reliability or connection problems are encountered.

Selection[edit | edit source]

For motor control applications it is recommended to get low to medium frequency ferrite cores for maximum efficiency.

Preferred types
  • Core material designed for low to medium frequency bands (attenuation between 1-300 MHz)
  • Large enough to fit cable multiple rounds through it
Avoid (might make things worse)
  • Core material designed for high frequency bands (above 300 MHz)
  • Inductor cores
  • Iron powder cores
  • Most ferrite & iron powder cores look same. If unsure about material properties, its most safe to purchase new low to medium frequency cores.

As example, take a look at Laird broadband and low frequency cores.

Where to find suitable cores[edit | edit source]

Ferrite cores are available from most electronic part distributors such as:

  • Digikey
  • Mouser
  • Farnell

Some popular ferrite core brands:

  • Laird-Signal Integrity Products
  • Fair-Rite

Usage[edit | edit source]

Application[edit | edit source]

Turning cable 2-3 times through core or using multiple in series increases filtering performance.
Correct installation of a core in 3 phase motor U,W and V wires and leaving PE wire out.

Application tips:

  • If possible, make 2-3 turns of cable through one core to maximize it's effectiveness
  • Place core close to interference source, not in the middle of the cable

With servo drives[edit | edit source]

To solve an EMI problem its good to have selection of cores that can be tried on different cables. Most typical placement for cores:

  • Motor output cable (all motor wires through core but not earth conductor). However, if earth conductor is hard to separate, then feeding all wires through core is still better than nothing.
  • High voltage power supply cable (+ and - leads through core)
  • USB adapter or other communication cables
  • Control I/O cables
  • Encoder/feedback device cable

See also[edit | edit source]