Difference between revisions of "IONICUBE connectors and pinouts"

From Granite Devices Knowledge Wiki
Jump to: navigation, search
[checked revision][checked revision]
(X4 pinout)
 
(31 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
==IONICUBE connectors==
 
==IONICUBE connectors==
Back side connectors consists:
 
 
;X1
 
;X1
 
:Dual port RJ45 connector with [[SimpleMotion V2]] interface. For pinout, see[[SimpleMotion V2 port]].  
 
:Dual port RJ45 connector with [[SimpleMotion V2]] interface. For pinout, see[[SimpleMotion V2 port]].  
Line 8: Line 7:
 
:Two pin wire terminal for [[HV DC bus]] supply.
 
:Two pin wire terminal for [[HV DC bus]] supply.
 
;X4
 
;X4
:Main control and [[setpoint]] signal port consisting Enable input signal, Fault output signal, [[pulse & direction]]/[[quadrature]]/[[PWM]] setpoint inputs and digital outputs for home switch status. X4 is directly wired to conform most common parallel port style pulse & direction CNC controllers.
+
:Main control and [[setpoint]] signal port consisting Enable input signal, Fault output signal, [[pulse and direction]]/[[quadrature]]/[[PWM]] setpoint inputs and digital outputs for home switch status. X4 is directly wired to conform most common parallel port style pulse & direction CNC controllers.
 
;X5
 
;X5
 
:Second control and [[setpoint]] signal port. This port consists analog setpoint signal inputs and additional digital I/O.
 
:Second control and [[setpoint]] signal port. This port consists analog setpoint signal inputs and additional digital I/O.
 
;X6
 
;X6
:These are the [[feedback devices]] connector for X (lower) and Y (upper) axis motors  
+
:These are the [[feedback devices|feedback device]] connector for X (lower) and Y (upper) axis motors  
 
;X7
 
;X7
:These are the power output connector for X (lower) and Y (upper) axis motors
+
:These are the power and holding brake output connector for X (lower) and Y (upper) axis motors
 
;X8
 
;X8
:These are the [[feedback devices]] connector for Z (lower) and A (upper) axis motors  
+
:These are the [[feedback devices|feedback device]] connector for Z (lower) and A (upper) axis motors  
 
;X9
 
;X9
:These are the power output connector for Z (lower) and A (upper) axis motors  
+
:These are the power and holding brake output connector for Z (lower) and A (upper) axis motors  
 +
;X10
 +
:A connector for an optional external [[regenerative resistor]]. IONICUBE has on-board regenerative resistor that is sufficient for most installations.
 +
;IONI_X, IONI_Y, IONI_Z, IONI_A
 +
:Card-edge connectors for IONI drives
 +
{{damage|Before inserting or removing IONI drives from IONICUBE, remove all power from it and discharge it's capacitors. To discharge remaining energy (~voltage) from capacitors, short circuit GND to HV+ by a conductor and measure that there is no DC voltage left between GND and HV+ terminals. Even few volts left to [[HV DC bus]] is known to cause permanent damage to IONICUBE when drives are plugged.}}
  
 
==Front side connectors==
 
==Front side connectors==
 
Front side connectors consist X6, X7, X8 and X9. These connectors are the interface towards motors (motor power and [[feedback devices]]).
 
Front side connectors consist X6, X7, X8 and X9. These connectors are the interface towards motors (motor power and [[feedback devices]]).
{{picturebox|Ionicubelayout.png|caption=Connector layout and naming}}
+
{{picturebox|Ionicubelayout.png|caption=Connector layout and naming. View from top of the board.}}
  
 +
{{picturebox|Ionicube revision 3 layout.png|caption=IONICUBE revision 3 PCB layout. USB connector X11 and Switch S1 to replace the jumper header.}}
  
{{picturebox|Ioni motoroutouts per drive.png|caption=Power and feedback ports of X, Y, Z and A axis}}
+
{{picturebox|Ioni motoroutouts per drive.png|caption=Power and feedback ports of X, Y, Z and A axis. View from plug side of the board.}}
  
  
{{picturebox|Ionicubemotorconnectors.png|caption=Names of power and feedback ports. I.e. X9A means upper floor connector of X9 and X9B the lower floor of X9.}}
+
{{picturebox|Ionicubemotorconnectors.png|caption=Names of power and feedback ports. I.e. X9A means upper floor connector of X9 and X9B the lower floor of X9. View from plug side of the board.}}
 
===Legend===
 
===Legend===
 
{| class="wikitable"
 
{| class="wikitable"
Line 34: Line 39:
 
! Color
 
! Color
 
|-
 
|-
| class="powpin"|Supply pin
+
| class="powpin" |Supply pin
 
|-
 
|-
| class="inpin"|Input pin
+
| class="inpin" |Input pin
 
|-
 
|-
| class="outpin"|Output pin
+
| class="outpin" |Output pin
 
|}
 
|}
 
===X7 and X9 pinout===
 
===X7 and X9 pinout===
 +
These are the power output and holding brake output connector for motors
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
!  Pin number !! Signal name !! Usage
+
!  Pin number !! Signal name !! AC/BLDC motor  !! Brush DC motor !! Stepping motor
 
|-
 
|-
| 1 ||class="powpin"| GND|| Ground for cable shield and an optional motor holding brake coil
+
| 1 || class="powpin" | GND|| colspan="3" | Ground for cable shield and an optional motor holding brake coil
 
|-
 
|-
| 2|| class="outpin"|PHASE1 || Motor phase 1
+
| 2|| class="outpin" |PHASE1 ||U (some motors R)||Armature +||Coil A.1
 
|-
 
|-
| 3|| class="outpin"|PHASE2 || Motor phase 2
+
| 3|| class="outpin" |PHASE2 ||V (some motors S)||Armature -||Coil A.2
 
|-
 
|-
| 4|| class="outpin"|PHASE3 || Motor phase 3
+
| 4|| class="outpin" |PHASE3 ||W (some motors T)||Armature -||Coil B.1
 
|-
 
|-
| 5|| class="outpin"|PHASE4 || Motor phase 4
+
| 5|| class="outpin" |PHASE4 || Not connected||Armature +||Coil B.2
 
|-
 
|-
| 6|| class="outpin"|BRAKE || 24V motor holding brake coil drive
+
| 6|| class="outpin" |BRAKE || colspan="3" |Optional 24V motor holding brake coil
 
|}
 
|}
 
====Motor & brake wiring schematics====
 
====Motor & brake wiring schematics====
Line 63: Line 69:
 
File:Ionicube mot step.png|Wiring of two phase stepping motor. Brake can be fitted like in the other examples. Also 6 and 8 wire motors can be wired (the two drive coils connect always to the same PHASE outputs).
 
File:Ionicube mot step.png|Wiring of two phase stepping motor. Brake can be fitted like in the other examples. Also 6 and 8 wire motors can be wired (the two drive coils connect always to the same PHASE outputs).
 
</gallery>
 
</gallery>
 +
{{tip|An easy way to verify correctness of two phase '''stepper''' connection: unplug the 6 pin connector and then measure resistance between phases 1-2 and 3-4. Multimeter should show the same resistance for both cases (typically 0.1 - 5 ohms). Also when measuring between phases 1-3, 1-4, 2-3 and 2-4, the multimeter should indicate open circuit.}}
  
 
===X6 and X8 pinout===
 
===X6 and X8 pinout===
{| class="wikitable"
+
X6 and X8 are the [[feedback devices|feedback device]] connectors of motors
|-
+
{{EncoderPinoutD15}}
! Pin # !! Pin name !! Electrical type (in most feedback device modes) || Alternate electrical type (in some feedback device modes) || Connection with various feedback devices
+
{{info|Especially with long encoder cables, it might be necessary to add encoder line termination resistors, see [[Terminating differential encoder lines]].}}
|-
+
| Shell||class="powpin"|GND|| colspan=2 |Earth/case  || Feedback cable shield
+
|-
+
| 1||class="inpin"|HALL_W|| colspan=2 |Digital input W ||  Hall sensor input, phase W
+
|-
+
| 2||class="inpin"|HALL_V|| colspan=2 |Digital input V  ||Hall sensor input, phase V
+
|-
+
| 3||class="inpin"|HALL_U|| colspan=2 |Digital input U || Hall sensor input, phase U
+
|-
+
| 4||class="powpin"|GND||colspan=2 |Encoder supply ground
+
|-
+
| 5||class="inpin"|B-||Differential input B-|| Analog input B+||rowspan=2|Quadrature encoder (B channel)/SinCos/serial encoder/resolver input
+
|-
+
| 6||class="inpin"|B+||Differential input B+|| Analog input B-
+
|-
+
| 7||class="inpin"|A-||Differential input A-|| Analog input A-||rowspan=2|Quadrature encoder (A channel)/SinCos/serial encoder/resolver input
+
|-
+
| 8||class="inpin"|A+||Differential input A+|| Analog input A+
+
|-
+
| 9|| class="powpin"|5V_OUT||colspan=2 |Encoder supply 5V output  || rowspan=2|Encoder power supply
+
|-
+
| 10|| class="powpin"|GND ||colspan=2 |Encoder supply ground
+
|-
+
| 11|| class="inpin"|GPI3||colspan=2|Axis negative direction end limit switch (optional)|| Connect normally closed (NC) limit switch between this pin and GND pin
+
|-
+
| 12|| class="inpin"|GPI2||colspan=2|Axis positive direction end limit switch (optional)|| Connect normally closed (NC) limit switch between this pin and GND pin
+
|-
+
| 13|| class="inpin"|GPI1||colspan=2|Axis home switch switch (optional)|| Connect normally closed (NC) limit switch between this pin and GND pin
+
|-
+
| 14|| class="inpin"|C-||colspan=2 |Differential input C- ||rowspan=2|Quadrature encoder index channel (Z channel)/serial encoder input
+
|-
+
| 15||class="inpin"| C+||colspan=2 |Differential input C+
+
|}
+
 
====Examples of feedback device and switch wiring====
 
====Examples of feedback device and switch wiring====
 
<gallery widths="180px" heights="180px">
 
<gallery widths="180px" heights="180px">
Line 129: Line 103:
 
!  Pin number !! Signal name !! Usage
 
!  Pin number !! Signal name !! Usage
 
|-
 
|-
| 1 ||class="powpin"| GND|| Ground
+
| 1 || class="powpin" | GND|| Ground
 
|-
 
|-
| 2|| class="powpin"|24V || 24V logic supply
+
| 2|| class="powpin" |24V || 24V logic supply
 
|-
 
|-
| 3|| class="inpin"|STO || Safe torque off input (this pin also available in X1, as defined in [[SimpleMotion V2 port]]
+
| 3|| class="inpin" |STO || Safe torque off input (this pin also available in X1, as defined in [[SimpleMotion V2 port]]
 
|-
 
|-
| 4||class="outpin"| VFD || 0-12V analog output where voltage level is proportional to [[PWM]] duty cycle on pin PWM on X4. PWM frequency must be between 100 and 10000 Hz.
+
| 4|| class="outpin" | VFD || 0-12V analog output where voltage level is proportional to [[PWM]] duty cycle on pin PWM on X4. PWM frequency must be between 100 and 10000 Hz.
 
|-
 
|-
| 5|| class="outpin"|RL1 || Relay coil driver output 1. When RLIN1 on X4 is logic high, RL1 is pulled to GND by an open collector circuit. When RLIN1 is low, RL1 is floating (max 24V).
+
| 5|| class="outpin" |RL1 || Relay coil driver output 1. When RLIN1 on X4 is logic high, RL1 is pulled to GND by an open collector circuit. When RLIN1 is low, RL1 is floating (max 24V). When connecting a relay that has 24VDC coil between RL1 and supplied 24V, no external free-wheeling diode is needed. Output current rating is max 500 mA.
 
|-
 
|-
| 6|| class="outpin"|RL2 || Relay coil driver output 2. When RLIN2 on X4 is logic high, RL2 is pulled to GND by an open collector circuit. When RLIN1 is low, RL2 is floating (max 24V).
+
| 6|| class="outpin" |RL2 || Relay coil driver output 2. When RLIN2 on X4 is logic high, RL2 is pulled to GND by an open collector circuit. When RLIN1 is low, RL2 is floating (max 24V). When connecting a relay that has 24VDC coil between RL2 and supplied 24V, no external free-wheeling diode is needed. Output current rating is max 500 mA.
 
|}
 
|}
 +
 
===X3 pinout===
 
===X3 pinout===
 
X3 is two pin wire terminal for [[HV DC bus]] supply.
 
X3 is two pin wire terminal for [[HV DC bus]] supply.
Line 147: Line 122:
 
!  Pin number !! Signal name !! Usage
 
!  Pin number !! Signal name !! Usage
 
|-
 
|-
| 1 ||class="powpin"| GND|| Ground
+
| 1 || class="powpin" | GND|| Ground
 
|-
 
|-
| 2|| class="powpin"|HV+ || Motor power supply, [[HV DC bus]] (see IONI drive voltage range spec)
+
| 2|| class="powpin" |HV+ || Motor power supply, [[HV DC bus]] (see IONI drive voltage range spec)
 
|}
 
|}
 +
See also:
 +
*[[IONI power supply schemes]]
 +
*[[Estimating power need of motor drive system]]
 +
{{info|If using switching power supply (SMPS) as motor power supply, external rectifier diodes are needed to protect the power supplies. See See [[IONI power supply schemes]].}}
  
 
===X4 pinout===
 
===X4 pinout===
X4 is main control and [[setpoint]] signal port consisting Enable input signal, Fault output signal, [[pulse & direction]]/[[quadrature]]/[[PWM]] setpoint inputs and digital outputs for home switch status. X4 is directly wired to conform most common parallel port style pulse & direction CNC controllers.
+
X4 is main control and [[setpoint]] signal port consisting Enable input signal, Fault output signal, [[pulse and direction]]/[[quadrature]]/[[PWM]] setpoint inputs and digital outputs for home switch status. X4 is directly wired to conform most common parallel port style pulse & direction CNC controllers.
 
{| class="wikitable"
 
{| class="wikitable"
 
! Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
 
! Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
|rowspan=14 class="tableseparator"|
+
| rowspan="14" class="tableseparator" |
 
!Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
 
!Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
 
|-
 
|-
| 1||1||class="inpin"|ENABLE |||Enable all axis (with or without chargepump)||2||14||class="inpin"|PWM||[[PWM]] input for VFD analog output
+
| 1||1|| class="inpin" |ENABLE |||Enable all axis (with or without chargepump)||2||14|| class="inpin" |PWM||[[PWM]] input for VFD analog output
 
|-
 
|-
| 3||2||class="inpin"|HSIN1_X||Direction input X||4||15||class="outpin"|GPO4_A||Limit switch output A
+
| 3||2|| class="inpin" |HSIN1_X||Pulse/step input X||4||15|| class="outpin" |GPO4_A||Limit switch output A
 
|-
 
|-
| 5||3||class="inpin"|HSIN2_X||Pulse/step input X||6||16||class="inpin"|RLIN1||Controls RL1 state
+
| 5||3|| class="inpin" |HSIN2_X||Direction input X||6||16|| class="inpin" |RLIN1||Controls RL1 state
 
|-
 
|-
| 7||4||class="inpin"|HSIN1_Y||Direction input Y||8||17||class="inpin"|RLIN2||Controls RL2 state
+
| 7||4|| class="inpin" |HSIN1_Y||Pulse/step input Y||8||17|| class="inpin" |RLIN2||Controls RL2 state
 
|-
 
|-
| 9||5||class="inpin"|HSIN2_Y||Pulse/step input Y||10||18||class="powpin"|GND||rowspan=8|Ground
+
| 9||5|| class="inpin" |HSIN2_Y||Direction input Y||10||18|| class="powpin" |GND|| rowspan="8" |Ground
 
|-
 
|-
| 11||6||class="inpin"|HSIN1_Z||Direction input Z||12||19||class="powpin"|GND
+
| 11||6|| class="inpin" |HSIN1_Z||Pulse/step input Z||12||19|| class="powpin" |GND
 
|-
 
|-
| 13||7||class="inpin"|HSIN2_Z||Pulse/step input A||14||20||class="powpin"|GND
+
| 13||7|| class="inpin" |HSIN2_Z||Direction input Z||14||20|| class="powpin" |GND
 
|-
 
|-
| 15||8||class="inpin"|HSIN1_A||Direction input A||16||21||class="powpin"|GND
+
| 15||8|| class="inpin" |HSIN1_A||Pulse/step input A||16||21|| class="powpin" |GND
 
|-
 
|-
| 17||9||class="inpin"|HSIN2_A||Pulse/step input A||18||22||class="powpin"|GND
+
| 17||9|| class="inpin" |HSIN2_A||Direction input A||18||22|| class="powpin" |GND
 
|-
 
|-
| 19||10||class="outpin"|STOP_OUT||Fault on any axis or E-stop (active low)||20||23||class="powpin"|GND
+
| 19||10|| class="outpin" |STOP_OUT||Fault on any axis or E-stop (active low). Note: this is IONI's GPO3 signals connected in parallel between all axis / [https://en.wikipedia.org/wiki/Wired_logic_connection wired-or configuration].||20||23|| class="powpin" |GND
 
|-
 
|-
| 21||11||class="outpin"|GPO4_X||Limit switch output X||22||24||class="powpin"|GND
+
| 21||11|| class="outpin" |GPO4_X||Limit switch output X||22||24|| class="powpin" |GND
 
|-
 
|-
| 23||12||class="outpin"|GPO4_Y||Limit switch output Y||24||25||class="powpin"|GND
+
| 23||12|| class="outpin" |GPO4_Y||Limit switch output Y||24||25|| class="powpin" |GND
 
|-
 
|-
| 25||13||class="outpin"|GPO4_Z||Limit switch output Z||26||N/A||Not connected||
+
| 25||13|| class="outpin" |GPO4_Z||Limit switch output Z||26||N/A||Not connected||
 +
|-
 +
| Pin layout || colspan=8 | [[File:26_pin_header_pinout.png|frameless|500x500px]]
 
|}
 
|}
 +
{{damage|Connect only to 3.3V or 5V logic circuits go any GPI, GPO and HSIN pins. Most of X4 & X5 pins are directly routed to IONI drive pins and [[IONI connector pinout|IONI electrical ratings]] apply.}}
 +
 +
====Alternative setpoint signals====
 +
{{Template:IONI setpoint signals}}
  
 
===X5 pinout===
 
===X5 pinout===
Line 190: Line 175:
 
{| class="wikitable"
 
{| class="wikitable"
 
! Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
 
! Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
|rowspan=14 class="tableseparator"|
+
| rowspan="14" class="tableseparator" |
 
!Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
 
!Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
 
|-
 
|-
| 1||1||class="powpin"|GND||||2||14||class="powpin"|+5V_OUT||5V supply from IONICUBE ^2
+
| 1||1|| class="powpin" |GND||||2||14|| class="powpin" |+5V_OUT||5V supply from IONICUBE ^2
 
|-
 
|-
| 3||2||class="inpin"|ANAIN-_X||+/-10V analog input X||4||15||class="inpin"|ANAIN+_X||+/-10V analog input X
+
| 3||2|| class="inpin" |ANAIN-_X||+/-10V analog input X||4||15|| class="inpin" |ANAIN+_X||+/-10V analog input X
 
|-
 
|-
| 5||3||class="inpin"|ANAIN-_Y||+/-10V analog input Y||6||16||class="inpin"|ANAIN+_Y||+/-10V analog input Y
+
| 5||3|| class="inpin" |ANAIN-_Y||+/-10V analog input Y||6||16|| class="inpin" |ANAIN+_Y||+/-10V analog input Y
 
|-
 
|-
| 7||4||class="inpin"|ANAIN-_Z||+/-10V analog input Z||8||17||class="inpin"|ANAIN+_Z||+/-10V analog input Z
+
| 7||4|| class="inpin" |ANAIN-_Z||+/-10V analog input Z||8||17|| class="inpin" |ANAIN+_Z||+/-10V analog input Z
 
|-
 
|-
| 9||5||class="inpin"|ANAIN-_A||+/-10V analog input A||10||18||class="inpin"|ANAIN+_A||+/-10V analog input A
+
| 9||5|| class="inpin" |ANAIN-_A||+/-10V analog input A||10||18|| class="inpin" |ANAIN+_A||+/-10V analog input A
 
|-
 
|-
| 11||6||class="outpin"|GPO1_X||rowspan=8|For pin function, refer to [[IONI connector pinout]] ||12||19||class="inpin"|GPI4_X||rowspan=8|For pin function, refer to [[IONI connector pinout]]
+
| 11||6|| class="outpin" |GPO1_X|| rowspan="8" |For pin function, refer to [[IONI connector pinout]] ||12||19|| class="inpin" |GPI4_X|| rowspan="8" |For pin function, refer to [[IONI connector pinout]]
 
|-
 
|-
| 13||7||class="outpin"|GPO1_Y  ||14||20||class="inpin"|GPI4_Y
+
| 13||7|| class="outpin" |GPO1_Y  ||14||20|| class="inpin" |GPI4_Y
 
|-
 
|-
| 15||8||class="outpin"|GPO1_Z ||16||21||class="inpin"|GPI4_Z
+
| 15||8|| class="outpin" |GPO1_Z ||16||21|| class="inpin" |GPI4_Z
 
|-
 
|-
| 17||9||class="outpin"|GPO1_A ||18||22||class="inpin"|GPI4_A
+
| 17||9|| class="outpin" |GPO1_A ||18||22|| class="inpin" |GPI4_A
 
|-
 
|-
| 19||10||class="outpin"|GPO5_X ||20||23||class="inpin"|GPI5_X
+
| 19||10|| class="outpin" |GPO5_X ||20||23|| class="inpin" |GPI5_X
 
|-
 
|-
| 21||11||class="outpin"|GPO5_Y ||22||24||class="inpin"|GPI5_Y
+
| 21||11|| class="outpin" |GPO5_Y ||22||24|| class="inpin" |GPI5_Y
 
|-
 
|-
| 23||12||class="outpin"|GPO5_Z ||24||25||class="inpin"|GPI5_Z
+
| 23||12|| class="outpin" |GPO5_Z ||24||25|| class="inpin" |GPI5_Z
 
|-
 
|-
| 25||13||class="outpin"|GPO5_A ||26||N/A||class="inpin"|GPI5_A
+
| 25||13|| class="outpin" |GPO5_A ||26||N/A|| class="inpin" |GPI5_A
 +
|-
 +
| Pin layout || colspan=8 | [[File:26_pin_header_pinout.png|frameless|500x500px]]
 
|}
 
|}
  
<gallery widths="180px" heights="180px">
+
== Application example ==
File:ionicube stepdir.png|A typical connection with legacy parallel port style CNC controller such as [[Mach3]]/[[Mach4]]/[[LinuxCNC]]. A 26 pin ribbon cable may be directly connected to PC parallel port or to equivalent pinout step/dir generator such as [[SmoothStepper]].
+
Follwing image shows typical installation schemes for pulse/direction controlled systems, typically found in PC CNC applications.<gallery widths="180px" heights="180px">
 +
File:ionicube stepdir.png|A typical connection with parallel port style CNC controller such as [[Mach3]]/[[Mach4]]/[[LinuxCNC]]. A 26 pin ribbon cable may be directly connected to PC parallel port or to equivalent pinout step/dir generator such as [[SmoothStepper]].
 
</gallery>
 
</gallery>
  
[[category:IONI user guide]]
+
[[Category:IONI_user_guide]]
[[category:IONICUBE]]
+
[[Category:IONICUBE]]

Latest revision as of 12:35, 11 December 2017

IONICUBE connectors[edit | edit source]

X1
Dual port RJ45 connector with SimpleMotion V2 interface. For pinout, seeSimpleMotion V2 port.
X2
6 pin wire terminal for logic voltage supply, Safe torque off input, analog output and relay driver outputs.
X3
Two pin wire terminal for HV DC bus supply.
X4
Main control and setpoint signal port consisting Enable input signal, Fault output signal, pulse and direction/quadrature/PWM setpoint inputs and digital outputs for home switch status. X4 is directly wired to conform most common parallel port style pulse & direction CNC controllers.
X5
Second control and setpoint signal port. This port consists analog setpoint signal inputs and additional digital I/O.
X6
These are the feedback device connector for X (lower) and Y (upper) axis motors
X7
These are the power and holding brake output connector for X (lower) and Y (upper) axis motors
X8
These are the feedback device connector for Z (lower) and A (upper) axis motors
X9
These are the power and holding brake output connector for Z (lower) and A (upper) axis motors
X10
A connector for an optional external regenerative resistor. IONICUBE has on-board regenerative resistor that is sufficient for most installations.
IONI_X, IONI_Y, IONI_Z, IONI_A
Card-edge connectors for IONI drives

Front side connectors[edit | edit source]

Front side connectors consist X6, X7, X8 and X9. These connectors are the interface towards motors (motor power and feedback devices).

Ionicubelayout.png

Connector layout and naming. View from top of the board.

Ionicube revision 3 layout.png

IONICUBE revision 3 PCB layout. USB connector X11 and Switch S1 to replace the jumper header.

Ioni motoroutouts per drive.png

Power and feedback ports of X, Y, Z and A axis. View from plug side of the board.


Ionicubemotorconnectors.png

Names of power and feedback ports. I.e. X9A means upper floor connector of X9 and X9B the lower floor of X9. View from plug side of the board.

Legend[edit | edit source]

Color
Supply pin
Input pin
Output pin

X7 and X9 pinout[edit | edit source]

These are the power output and holding brake output connector for motors

Pin number Signal name AC/BLDC motor Brush DC motor Stepping motor
1 GND Ground for cable shield and an optional motor holding brake coil
2 PHASE1 U (some motors R) Armature + Coil A.1
3 PHASE2 V (some motors S) Armature - Coil A.2
4 PHASE3 W (some motors T) Armature - Coil B.1
5 PHASE4 Not connected Armature + Coil B.2
6 BRAKE Optional 24V motor holding brake coil

Motor & brake wiring schematics[edit | edit source]

X6 and X8 pinout[edit | edit source]

X6 and X8 are the feedback device connectors of motors

Pin # Pin name Electrical type (in most feedback device modes) Quadrature encoder SinCos encoder BiSS-C encoder SSI encoder AMS SSI encoder
Shell GND Earth/case
1 HALL_W Hall sensor digital input, phase W - - -
2 HALL_V Hall sensor digital input, phase V - - -
3 HALL_U Hall sensor digital input, phase U - - -
4 GND Encoder supply ground
5 B- Differential input B- Channel B- SinCos input B- - - -
6 B+ Differential input B+ Channel B+ SinCos input B+ - - -
7 A- Differential input A- Channel A- SinCos input A- - - -
8 A+ Differential input A+ Channel A+ SinCos input A+ - - -
9 5V_OUT Encoder supply 5V output
10 GND Encoder supply ground
11 GPI3 Axis negative direction end limit switch (optional). Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Limit switch polarityLSP.
Clock/MA- Clock- CLK
12 GPI2 Axis positive direction end limit switch (optional).Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Limit switch polarityLSP.
Clock/MA+ Clock+ CSn
13 GPI1 Axis home switch switch (optional). Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Home switch or hard stop search direction (Home switch polarity)HMS.
DO
14 C- Differential input C- Index channel Z- Index channel Z+ Data/SLO- Data- -
15 C+ Differential input C+ Index channel Z+ Index channel Z+ Data/SLO+ Data+ -
Pin layout Female D-sub 15 connector as it appears from outside of drive. Note: counterpart (male) connector has mirrored pin layout if viewed from pin side, and same layout if viewed from soldering side.

D15 pinout.png

Examples of feedback device and switch wiring[edit | edit source]


Back side connectors[edit | edit source]

Ionicube x2345.png

A closeup of X2, X3, X4 and X5


X2 pinout[edit | edit source]

X2 is 6 pin wire terminal for logic voltage supply, Safe torque off input, analog output and relay driver outputs.

Pin number Signal name Usage
1 GND Ground
2 24V 24V logic supply
3 STO Safe torque off input (this pin also available in X1, as defined in SimpleMotion V2 port
4 VFD 0-12V analog output where voltage level is proportional to PWM duty cycle on pin PWM on X4. PWM frequency must be between 100 and 10000 Hz.
5 RL1 Relay coil driver output 1. When RLIN1 on X4 is logic high, RL1 is pulled to GND by an open collector circuit. When RLIN1 is low, RL1 is floating (max 24V). When connecting a relay that has 24VDC coil between RL1 and supplied 24V, no external free-wheeling diode is needed. Output current rating is max 500 mA.
6 RL2 Relay coil driver output 2. When RLIN2 on X4 is logic high, RL2 is pulled to GND by an open collector circuit. When RLIN1 is low, RL2 is floating (max 24V). When connecting a relay that has 24VDC coil between RL2 and supplied 24V, no external free-wheeling diode is needed. Output current rating is max 500 mA.

X3 pinout[edit | edit source]

X3 is two pin wire terminal for HV DC bus supply.

Pin number Signal name Usage
1 GND Ground
2 HV+ Motor power supply, HV DC bus (see IONI drive voltage range spec)

See also:

X4 pinout[edit | edit source]

X4 is main control and setpoint signal port consisting Enable input signal, Fault output signal, pulse and direction/quadrature/PWM setpoint inputs and digital outputs for home switch status. X4 is directly wired to conform most common parallel port style pulse & direction CNC controllers.

Pin number in header Pin number in D25 cable Signal name Typical usage Pin number in header Pin number in D25 cable Signal name Typical usage
1 1 ENABLE Enable all axis (with or without chargepump) 2 14 PWM PWM input for VFD analog output
3 2 HSIN1_X Pulse/step input X 4 15 GPO4_A Limit switch output A
5 3 HSIN2_X Direction input X 6 16 RLIN1 Controls RL1 state
7 4 HSIN1_Y Pulse/step input Y 8 17 RLIN2 Controls RL2 state
9 5 HSIN2_Y Direction input Y 10 18 GND Ground
11 6 HSIN1_Z Pulse/step input Z 12 19 GND
13 7 HSIN2_Z Direction input Z 14 20 GND
15 8 HSIN1_A Pulse/step input A 16 21 GND
17 9 HSIN2_A Direction input A 18 22 GND
19 10 STOP_OUT Fault on any axis or E-stop (active low). Note: this is IONI's GPO3 signals connected in parallel between all axis / wired-or configuration. 20 23 GND
21 11 GPO4_X Limit switch output X 22 24 GND
23 12 GPO4_Y Limit switch output Y 24 25 GND
25 13 GPO4_Z Limit switch output Z 26 N/A Not connected
Pin layout 26 pin header pinout.png

Alternative setpoint signals[edit | edit source]

Setpoint mode is selected by software with parameter Setpoint inputCRI and behavior is affected by parameters Setpoint smoothingCIS, Setpoint multiplierMUL, Setpoint dividerDIV, Setpoint offset nullingCAO and Enable direction inputCED.

Signal name Function Used for Remarks
HSIN1 High speed digital input 1 Depending on setpoint mode, can be either:
HSIN2 High speed digital input 2 Depending on setpoint mode, can be either:
  • Direction signal of pulse train (in Pulse and direction setpoint mode)
  • Quadrature B channel (in quadrature setpoint mode)
  • PWM (in PWM and PWM+Dir setpoint modes)
ANAIN- Differential analog negative input Used for analog setpoint mode Setpoint voltage is the voltage difference between ANAIN+ and ANAIN-
ANAIN+ Differential analog positive input Used for analog setpoint mode

X5 pinout[edit | edit source]

X5 is a second control and setpoint signal port in addition to X4. This port consists analog setpoint signal inputs and additional digital I/O.

Pin number in header Pin number in D25 cable Signal name Typical usage Pin number in header Pin number in D25 cable Signal name Typical usage
1 1 GND 2 14 +5V_OUT 5V supply from IONICUBE ^2
3 2 ANAIN-_X +/-10V analog input X 4 15 ANAIN+_X +/-10V analog input X
5 3 ANAIN-_Y +/-10V analog input Y 6 16 ANAIN+_Y +/-10V analog input Y
7 4 ANAIN-_Z +/-10V analog input Z 8 17 ANAIN+_Z +/-10V analog input Z
9 5 ANAIN-_A +/-10V analog input A 10 18 ANAIN+_A +/-10V analog input A
11 6 GPO1_X For pin function, refer to IONI connector pinout 12 19 GPI4_X For pin function, refer to IONI connector pinout
13 7 GPO1_Y 14 20 GPI4_Y
15 8 GPO1_Z 16 21 GPI4_Z
17 9 GPO1_A 18 22 GPI4_A
19 10 GPO5_X 20 23 GPI5_X
21 11 GPO5_Y 22 24 GPI5_Y
23 12 GPO5_Z 24 25 GPI5_Z
25 13 GPO5_A 26 N/A GPI5_A
Pin layout 26 pin header pinout.png

Application example[edit | edit source]

Follwing image shows typical installation schemes for pulse/direction controlled systems, typically found in PC CNC applications.