IONI user guidebook

From Granite Devices Knowledge Wiki
Revision as of 10:17, 23 February 2018 by Esa (Talk | contribs) (Set-up overwies & first connection)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

Jump to: navigation, search

This page collect most of the IONI & IONICUBE user guide articles as a single page.

Introduction to IONI[edit | edit source]

IONI
Finalioni2crop.JPG
Device type Servo & stepping motor drive
Model number IONI-11K000, IONI-11K200
Supported motors AC, DC, BLDC, Linear, Stepper
Control modes Position, Velocity, Torque
Status Active production, started 2015
Electrical
DC supply voltage 5 - 54 VDC (except 5 - 58 VDC in IONI Pro HC)
Output current range 0.1 - 15A IONI, 0.1 - 18A IONI Pro, 0.1 - 25A IONI Pro HC
Setpoint signals Pulse and direction, PWM, Analog, SimpleMotion V2
Feedback devices Quadrature encoder, SinCos encoder
General
Configuration tool Granity
Web site Granite Devices IONI
Compliance CE (EMC & LVD directives)
3D model

Download-icon.png IGES & STEP

PDF version of IONI flyer. Download.

IONI is a digital motor drive designed for driving AC/BLDC and DC servo motors and steppers. IONI allows controlling motors in all three operating modes: position control, velocity control and torque control (torque mode only with servo motors). Applications of such control methods include

  • Position control, such as CNC, robotics and 3D printing
  • Velocity control, such as spindles or feeders
  • Force / torque control, such as racing simulator wheel


Ioni drive blocks.png


Commands to IONI drive can be delivered in many formats and from many sources, such as PC, PLC, microcontroller (i.e. Arduino, MBED and OEM boards) or embedded computers like Raspberry Pi. IONI understands several forms of setpoint commands:

  • Step & direction digital signals (typical stepper drive interface, good for position control)
  • Analog +/-10V signal (good for speed or torque control)
  • PWM signal (good for speed or torque control)
  • RS485 serial bus (talks SimpleMotion V2 bus protocol, open source library available)


Supported motors[edit | edit source]

As motor is not included, make sure that you have, or obtain a motor that is compatible with IONI. Learn more about motor types.

Servo motor requirements[edit | edit source]

  • Permanent magnet brush-DC, AC, brushless or linear motor
  • Motor voltage rating 12-60 VDC (IONI supply voltage is 5 - 52 VDC)
  • Motor current rating 0.1 - 25A (choose drive model accordingly, IONI Pro HC, maximum output is 25A, IONI Pro 18A, and IONI 15A)
  • Servo motor must be equipped with an supported feedback device (position sensor / encoder).

See Motor compatibility guide for more details.

Stepping motor requirements[edit | edit source]

  • Two-phase stepping motor with 0.5 - 15A current rating, no feedback device needed. Can be used in position and velocity control mode. Torque mode not possible. Stepper voltage rating is irrelevant, but generally lower voltage & higher current stepper is better.

Unsuitable/non-optimum motors[edit | edit source]

  • Any non-permanent magnet motors: induction AC motor or DC motor with field coil - will not work
  • Cheapest grade DC motor, such as one extracted from power drill - might not give satisfying performance
  • Motor with very high voltage, such as 200 VAC AC servo motor - it will work if it has incremental encoder feedback, but maximum rotation speed is limited due to drive voltage. Consider Argon servo drive for motors above 100 volts rating.

Features[edit | edit source]

State of the Art[edit | edit source]

Control[edit | edit source]

Protections & Ruggedness[edit | edit source]

  • Safe torque off
  • Prevent machine damage via I²t (motor temperature modeling), blocked motion and tracking error detection
  • Industry leading ruggedness: over current, short circuit, over voltage, under voltage and over temperature protections, data/communication error detection
  • Warranty 24 months
  • Charge pump enable input for safety

Applications[edit | edit source]

  • Industrial servo & stepping motor control
  • Robotics
  • Industry 4.0 systems
  • Testing equipment
  • CNC
  • Haptics
  • Racing & flight simulators
  • Pick'n'place machines
  • Defense systems

Functionality and specifications[edit | edit source]

See main article IONI specifications.

Documentation & user guides[edit | edit source]

See the main article IONI & IONICUBE user guide.

Availability[edit | edit source]

Shipping worldwide at Granite Devices web shop.

IONI specifications[edit | edit source]

Contents

This page lists official functional, electrical and physical specifications of the IONI Servo Drive.

Device variations[edit | edit source]

IONI is available in three different models. See also IONI device model comparison.

IONI
Standard model
IONI Pro
Advanced model, additional features and increased current range
IONI Pro HC
Same features as IONI Pro, except higher current and voltage range

Main functionality[edit | edit source]

Function Description
Servo/stepping motor drive Closed loop control of various types of servo motors by sinusoidal field oriented control with dead-time distortion correction and high dynamic range torque control.
  • Synchronous AC & BLDC motors
    • Sinusoidal and trapezoidal commutated
    • SPM (Surface Permanent Magnet) and IPM (Internal Permanent Magnet) types
  • Brush DC motors
  • Linear motors
    • Iron core
    • Ironless (with external inductive filter)
  • Stepping motor, 2 phase (4,6 or 8 wires)
Control modes
  • Torque control
  • Velocity/speed control
  • Position control
Setpoint types

See setpoint signal / reference inputs list

Closed loop Cascaded control loops (PIV):
  • Torque / current control, update frequency 20.0 kHz
  • Velocity control, update frequency 2.5 kHz
  • Position control, update frequency 2.5 kHz
Feed-forwards Feed-forwards working in velocity & position control modes:
  • Acceleration (inertia canceling) feed-forward
  • Velocity (friction canceling) feed-forward
Homing Integrated homing function for position control mode:
  • Sensorless hard-stop homing
  • Home switch search
  • Index pulse search
  • Soft position limits (eliminate limit switches)
Feedback devices See feedback devices list
Safety
  • Safe torque off with 3-way redundancy
  • Charge pump enable input
  • Stopping motor on errors
    • Tracking error (velocity & position)
    • Over speed error
    • Limit switch
  • DC motor runaway prevention on feedback loss
  • Communication error detection
Protections
  • Over current
  • Short circuit (phase-to-phase)
  • I2t motor thermal protection
  • Over & under voltage
  • Over temperature
Power supply
  • Externally supplied
    • IONI, IONI Pro 5 – 52 VDC
    • IONI Pro HC 5 - 55 VDC
  • Additionally an external 5 VDC logic supply required. Note: if drive is used with IONICUBE motherboards, then 24 VDC logic supply voltage is needed instead as IONICUBE has on-board 5V regulator.
Motor output current1
  • AC/BLDC/Stepping/Linear motors (current specified as peak of sine):
    • IONI 0-15 A
    • IONI Pro 0-18 A
    • IONI Pro HC 0-25 A
  • Brush DC motors:
    • IONI 0-19.5 A
    • IONI Pro 0-23.4 A
    • IONI Pro HC 0-30 A
Commissioning
Compliance CE (LVD & EMC): EN IEC 62368-1:2018, IEC 61000-6-1:2005 and IEC 61000-6-3:2006.

SIL2: IEC 61800-5-2:2016-04

Notes:

  • In order to meet EMC standard requirements, a proper installation and wiring is necessary. Refer to user guide for proper installation.
  • Signed Declaration of Conformity will be provided on request.
Reliability
  • MTBF: 2.99 million hours
  • Failure rate (all delivered units, actual statistic from 2015-2017): 0.36%

1) Currents achievable continuously only with with sufficient coolant air flow. Without forced cooling, typically 30-45% of the maximum range can be driven continuously. Despite of this, maximum current is available for short periods of time even without cooling. Current is automatically throttled on temperature rise to protect the drive.

Mechanical[edit | edit source]

Property Value Units
Dimensions 70.5 × 37 × 7.5 (W×H×D) mm
Weight 14.0 ± 0.5 g
Drawings Download-icon.png 2D (PDF), Download-icon.png 3D (IGES & STEP)
Pinout IONI connector pinout

Environment[edit | edit source]

Property Value Units
Operating temperature -10...+75, non condensing °C
Storage temperature -30...+90, non condensing °C
Humidity 0-95 non-condensing  %
Power dissipation 0.3-15¹ W

¹) Power dissipation is output current and input voltage related.

Power supply[edit | edit source]

Supply2 Input voltage Input current typ Input current max
Logic power 5 VDC +/- 10%4 0.1 - 0.3 A 0.2 A
Motor power 5 - 52 VDC3 (IONI, IONI Pro), 5 - 55 VDC 3 (IONI Pro HC) 0 - 23.5 A1 23.5 A1

1) Estimating true current or power consumption based on this table may be difficult as current demand typically varies greatly and and almost completely depends on motor load conditions.

2) Both logic and motor supplies are required.

3) Possible to use from 5 VDC upwards, however short circuit protection feature is lost below 12 VDC.

4) IONICUBE motherboards provide on-board 5V regulator and accepts 24 VDC logic supply voltage. With IONICUBE no 5V supply is needed.

Motor output[edit | edit source]

Maximum output current throttling vs device temperature. Current is automatically reduced by device to protect from overheating.
Property Value Units Remarks
Supported motors AC, BLDC, DC, Linear Permanent magnet motors only
Continuous output current 0-151 (IONI), 0-181 (IONI Pro), 0-251 (IONI Pro HC) A (peak value of sine) User settable limit
Peak output current 0-151 (IONI), 0-181 (IONI Pro), 0-251 (IONI Pro HC) A (peak value of sine) User settable current limit.
Maximum effective motor phase output voltage
  • 3-phase AC motors: Vsupply*0.671 V RMS (phase-to-phase)
  • DC motors: Vsupply*0.95 VDC
  • I.e. at 48V supply, the maximum three-phase motor output voltage is 32.2 V RMS phase-to-phase
  • I.e. at 48V supply, the maximum DC motor output voltage is 45.6 V
Switching frequency 20.0 kHz
Maximum modulation depth 95  % Maximum effective output is 95% of HV DC bus voltage.
Torque control bandwidth (typ.) 1-3.3 kHz Motor coil dependent
Torque control cycle time 50.0 µs
Position & velocity control cycle time 400 µs
Power conversion efficiency 93-97  % Under typical conditions
Motor inductance range @ 48 VDC 0.2-25 mH
Motor inductance range @ 24 VDC 0.1-25 mH
Motor power range 0.01 - 0.5 kW
AC commutation frequency 0-400 Hz Not capped, may achieve up to 2 kHz

1) Maximum current is obtainable only for short periods without active air cooling. Drive automatically throttles current limit if drive temperature rises beyond 75 Celsius. Output current capacity reduces linearly between 75 and 90 degrees Celsius from the maximum to zero.

Regenerative resistor[edit | edit source]

IONI has a dedicated 3.3V logic level output for regenerative resistor control. The logic signal can be externally fed to a switch component (such as MOSFET) to drive external regenerative resistor to prevent overvoltage during rapid motor decelerations.

Feedback devices[edit | edit source]

Status of feedback device support[edit | edit source]

Feedback device type Status Electrical interface
Quadrature incremental encoder Standard feature Differential 3-5.5V (RS422), Single ended 3-5.5V (CMOS,TTL,open collector)
Hall sensors Standard feature Single ended 3-5.5V (CMOS,TTL,open collector). Differential signals accepted.
Analog SinCos encoder Standard feature in IONI Pro 1 V p-p signal, user selectable 16X, 64X or 256X resolution interpolation factor (note 1). Automatic signal gain and offset calibration (info about Lissajous tuning).
Serial SSI absolute encoder Standard feature in IONI Pro, see more info RS422/RS485
Serial BiSS absolute encoder Standard feature in IONI Pro, see more info RS422/RS485

1) The final resolution will be 4*line_count*interpolation_factor. I.e. with 1000 lines/electrical cycles per revolution SinCos encoder, the supported resolutions are 64000, 256000 and 1024000 counts per revolution. SinCos encoder can be also used without interpolation (4*line_count resolution).

Quadrature & SinCos encoder electrical properties[edit | edit source]

Property Value Units Remarks
Encoder count rate
  • IONI: 0-4
  • IONI Pro: 0-18
MHz After 4x decoding, digitally filtered
SinCos encoder input frequency
  • IONI Pro: 0-1
MHz Max theoretical count rate at 256X interpolation becomes 1MHz*4*256 = 1024 MHz, however parameter Over speed faultFEV accepted value range might limit the achievable count rate to 75 MHz.
Supply voltage 4.8-5.2 V Supplied externally (can share same voltage with drive logic supply)

Setpoint signal / reference inputs[edit | edit source]

Setpoint signal type Status Electrical interface
Analog Standard feature
  • Up to +/-10V or any lower voltage range
  • +/-10V (bipolar) and 0-10V with polarity input (unipolar) supported
Pulse and direction Standard feature

Maximum step rate

  • IONI: 4 MHz
  • IONI Pro: 8 MHz
Quadrature Standard feature

Maximum quadrature frequency (count rate)

  • IONI: 1 MHz (4 MHz)
  • IONI Pro: 2 MHz (8 MHz)
PWM Standard feature
  • 1-30 kHz PWM carrier frequency (fPWM), ~3 kHz for optimal operation.
  • Single signal (no polarity input), zero setpoint at 50% duty
  • PWM signal is sampled at 60MHz timer thus reading resolution is 60MHz/fPWM
  • PWM+Polarity input mode
Serial communication Standard feature SimpleMotion V2 real-time serial bus with open source SDK. Connect through RS485 or USB.
EtherCAT Under development Realized with add-on board, EtherFOX

See also:

Inputs / outputs[edit | edit source]

List of I/O's[edit | edit source]

  • Setpoint inputs
    • Two digital channels (pulse/dir, quadrature or PWM)
    • One +/-10V analog channel (differential, 2 wires)
  • Digital inputs
    • Switch inputs (3 channels): home switch, positive travel limit switch, negative travel limit switch
    • Status control inputs (3 channels): enable, clear faults, STO
  • Feedback inputs
    • Quadrature encoder (3 channels differential, where 2 channels capable of 12 bit analog sampling)
    • Hall sensors (3 channels)
  • Digital outputs (3.3V logic level)
    • Regenerative brake control output (external power switch needed, such as MOSFET)
    • Holding brake control output (external power switch needed, such as MOSFET)
    • Status indication outputs (3 channels): fault stop, servo ready, tracking error warning
  • Serial comminication interfaces

Electrical characteristics[edit | edit source]

  • Digital inputs accept standard signal levels 2.7 - 5.5 VDC, except STO and Enable inputs accept 4 - 26 VDC.
  • Digital outputs provide 3.3 VDC signal level
  • Analog inputs accept +-/10 VDC (+/- 12 VDC max) referenced to GND

Detailed properties[edit | edit source]

For detailed pin specific description and electrical ratings, see IONI connector pinout.

Communication[edit | edit source]

Property Value Units
Communication protocol SimpleMotion V2
Default bitrate 460.8 kBPS
Supported high bit rates 1, 2, 3, 4, 4.5 MBPS
Maximum number of SMV2 devices chained in a single bus 32 pcs
Command throughput Up to 20000 Commands/s

Safety[edit | edit source]

Feature Properties Remarks
Safe torque off
  • One dedicated physical STO input
  1. Cut gate drive voltage rendering power stage inactive @ STO2 input
  2. Disable motor control @ STO2 input (software based)

Reaction time from STO2 signal voltage going below 2 volts to de-energized motor is maximum 5 ms.

Control error detection
  • Tracking error (velocity & position)
  • Over speed error
  • Limit switch
  • DC motor runaway prevention on feedback loss
  • Communication error
Electrical safety
  • ESD, short circuit, reverse polarity protection on all pins
Overload safety
  • Over current
  • Short circuit (phase-to-phase)
  • I2t motor thermal protection
  • Over & under voltage
  • Drive over temperature

Warnings[edit | edit source]

IONI pinout[edit | edit source]

IONI card edge connector fits into a standard PCI-Express 8X socket connector. This page lists electrical and functional specifications of each pin.

Pinout[edit | edit source]

Location of pins B1 to B49. A1 to A49 are on same order except on the opposite side of board.
IONI pin-out
Color
Power pin
Input pin
Output pin
Mixed or other purpose

The pinout of IONI drive is provided in the following table.

I/O and low voltage signals
Pin Signal name Pin Signal name
A1 GND B1 5V_IN
A2 RS485_A B2 RS485_B
A3 ADDRSEL1 B3 ADDRSEL2
A4 HSIN1 B4 HSIN2
A5 ANAIN- B5 ANAIN+
A6 GPI1 B6 GPI2
A7 GPI3 B7 GPI4
A8 GPO1 B8 GPO2
A9 GPO3 B9 GPO4
A10 GPO5 B10 GPI5
A11 REGEN_OUT B11 MECH_BRAKE_OUT
A12 ENABLE_IN B12 Reserved/NC
A13 STO2 B13 HALL_W
A14 HALL_V B14 HALL_U
A15 A- B15 A+
A16 B- B16 B+
A17 C- B17 C+
Power signals
Pin Signal name Pin Signal name
A18-A22 GND B18 Not connected
A23 Not connected B19-B22 HV+
A24-A27 PHASE1 B23 Not connected
A28 Not connected B24-B27 PHASE2
A29-A37 PHASE3 B28 Not connected
A38 Not connected B29-B37 PHASE4
A39-A43 PHASE1 B38 Not connected
A44 Not connected B39-B43 PHASE2
A45-A49 GND B44 Not connected
B45-B49 HV+
Connection to motor
Signal name AC/BLDC motor Brush DC motor Stepping motor
GND Connect motor cable shield and motor frame to power GND
PHASE1 U (some motors R) Armature + Coil A.1
PHASE2 V (some motors S) Armature - Coil A.2
PHASE3 W (some motors T) Connect to PHASE2 Coil B.1
PHASE4 Not connected Connect to PHASE1 Coil B.2

Note 1: pins marked as Not connected are left empty for to make larger clearance for high voltage signals. Leave these pins unconnected on motherboard designs.

Note 2: Each power signal is present in two pin groups (internally parallel) and these signals should be wired parallel on motherboard.

Signal assignment[edit | edit source]

General purpose I/O (GPI/GPO)[edit | edit source]

The table below summarizes the default functions for GPIO pins.

Signal name Function Used for Remarks
GPI1 Home switch Homing reference switch (optional), can also disable homing, or use Hard-stop homing without switch Note 1
GPI2 Enable positive feed Axis positive direction end limit switch (optional) Normally closed switch. When switch is open, motion/force in positive direction is prevented. 1
GPI3 Enable negative feed Axis negative direction end limit switch (optional) Normally closed switch. When switch is open, motion/force in negative direction is prevented. 1
GPI4 Clear faults Rising logic edge on this pin will clear fault state of drive In IONICUBE mode, also rising edge of enable signal will clear faults.
GPI5 Start homing Rising logic edge on this pin will start homing if homing is enabled
GPO1 Servo ready Use to indicate controller that drive is ready Logic 1 when drive has been initialized, enabled and ready to follow setpoint commands. If homing is enabled, then servo ready will be logic 1 after homing is successfully completed.
GPO2 Tracking error warning Use to indicate controller when drive is having difficulties following the setpoint before a tracking fault occurs Logic 1 when tracking error (position or velocity, depending on control mode) is greater than 1/8 of configured fault trigger level.
GPO3 Fault state (active low) Use to indicate controller that drive is stopped due to fault state In IONICUBE mode GPO3 goes logic 0 after when enable signal is set low (for Mach3 compatibility). GPO3 is open drain type to allow wired and connection.
GPO4 2-way travel allowed Use to indicate controller when axis is allowed to move in both directions (i.e. any limit switches not hit or axis lies within an optional homing defined limited travel range)
  • GPO4 will be logic high if both of "Pos feed enable" and "Neg feed enable" as seen in Granity status are true. These Pos/Neg feed enable states are affected by Limit switch polarityLSP.
  • If you see both Pos & Neg feed enables being false, then you probably need to invert the switches with LSP parameter.
  • GPO4 will be also false if limit switch has been configured as home switch and homing is being performed.
  • GPO4 will work also sensorless manner after performing hard-stop homing with active "soft travel limits", in such case GPO4 will indicate whether axis is within the allowed software configured motion range.
GPO5 Reserved Feel free to request custom signal from Granite Devices support to be added in this output. For example fan control or custom status output. Changes can be made in customer specific firmware.

1) Connect switch between GND and GPIn pin

See also Drive status & fault bits explained.

Setpoint signals[edit | edit source]

Setpoint mode is selected by software with parameter Setpoint inputCRI and behavior is affected by parameters Setpoint smoothingCIS, Setpoint multiplierMUL, Setpoint dividerDIV, Setpoint offset nullingCAO and Enable direction inputCED.

Signal name Function Used for Remarks
HSIN1 High speed digital input 1 Depending on setpoint mode, can be either:
HSIN2 High speed digital input 2 Depending on setpoint mode, can be either:
  • Direction signal of pulse train (in Pulse and direction setpoint mode)
  • Quadrature B channel (in quadrature setpoint mode)
  • PWM (in PWM and PWM+Dir setpoint modes)
ANAIN- Differential analog negative input Used for analog setpoint mode Setpoint voltage is the voltage difference between ANAIN+ and ANAIN-
ANAIN+ Differential analog positive input Used for analog setpoint mode

Feedback device signals[edit | edit source]

Signal name # Electrical type (in most feedback device modes) Alternate electrical type (in some feedback device modes) Connection with various feedback devices
HALL_W Digital input W Hall sensor input, phase W
HALL_V Digital input V Hall sensor input, phase V
HALL_U Digital input U Hall sensor input, phase U
A- Differential input A- Analog input A- Quadrature encoder (A channel)/SinCos A
A+ Differential input A+ Analog input A+
B- Differential input B- Analog input B+ Quadrature encoder (B channel)/SinCos B
B+ Differential input B+ Analog input B-
C- Differential input C- Quadrature encoder index channel (Z channel)
C+ Differential input C+

Other signals[edit | edit source]

Signal name Function Used for Remarks
REGEN_OUT Regenerative resistor control output Use to control optional regenerative resistor to prevent excessive voltage generation in HV DC bus during motor deceleration. A buffer circuit is needed for resistor, such as a logic level MOSFET. See example schematic here.
MECH_BRAKE_OUT Mechanical holding brake control output Use to control optional holding brake of motor A buffer circuit is needed to drive a solenoid brake, such as a logic level MOSFET. See example schematic here.
ENABLE_IN Drive enable input signal (always required) Use to enable drive and allow motor to initialize and operate Accepts up to 24V voltage level, but works also with 5V level signal. (1)
STO2 Safe torque off input signal (always required) Use to allow motor to produce torque (activate power stage) Accepts up to 24V voltage level, but works also with 5V level signal. STO is inactive (allows torque) when logic high is supplied. (1)

(1) ENABLE_IN and STO2 are not 3.3V compatible, 4.5-26V signal is required to drive logic true state into them.

Electrical ratings[edit | edit source]

IONI's internal circuity (equivalent schematics, not actual wiring) in feedback device port pins (the pins on D-15 connector on IONICUBEs)
Signal names Allowed input voltages/output voltage Internal input/output impedance (Ω) Internal pull impedance (Ω)
5V_IN 5V +/-10% - -
HV+ 0 – 55 V - -
RS485_A/B RS485 serial bus, 2.7-5.5V signal level >10k -
ADDRSEL1, ADDRSEL2 External address setting pull-down resistors to ground (minimum 1 kΩ). See chapter Selecting device address below. - 2.2k pull-up to 3.3V
HSIN1, HSIN2 Logic low -0.3-1.0V, logic high 2.7-5.5V - 2.2k pull-up to 3.3V
ANAIN-, ANAIN+ +/- 11V 8k -
GPI1...GPI4 Logic low -0.3-1.0V, logic high 2.7-5.5V - 2.2k pull-up to 3.3V
GPI5 Logic low -0.3-1.0V, logic high 2.7-5.5V -
  • Rev 1 drives: ~20-50k pull-up to 3.3V
  • Rev 2 and later: 3.3k pull-up to 5V
GPO1,2,4,5 Logic low 0V, logic high 3.3V 220 -
GPO3 Depends on Electrical interface Electrical interfaceCEI parameter: In IONICUBE mode it is an open drain output, pulled to 0V with 220 ohm impedance or pulled to 3.3V with pull-up (allow wired and connection of multiple drives). In other modes it is push-pull output (like GPO1,2,4,5) 220 ~20-50k pull-up to 3.3V
MECH_BRAKE_OUT Logic low 0V, logic high 3.3V 220 -
REGEN_OUT Logic low 0V, logic high 3.3V 220 -
ENABLE_IN Logic low -0.3-2.0V, logic high 4.5-26V 5k 10k pull-down to GND
STO2 Logic low -0.3-2.0V, logic high 4.5-26V 8k 20k pull-down to GND
HALL_U/V/W Logic low -0.3-1.0V, logic high 2.7-5.5V - 2.2k pull-up to 5V
A/B/C+ RS422 receiver, 2.7-5.5V signal level - 2.2k pull-up to 5V
A/B/C- RS422 receiver, 2.7-5.5V signal level - 1.9k pull to 1.9V

Electrical interface modes (software selectable)[edit | edit source]

IONI supports various function mappings to I/O signals and is selectable through Granity CEI Electrical interface parameter. The differences between modes are:

Mode Description Effects (change of operation compared to Standard in this mode)
Standard The default mode I/O assignments as described in pinout
IONICUBE (CNC applications) Mode for IONICUBE that is compatible with parallel port CNC controllers such as Mach3 and LinuxCNC software.

Not recommended with IONICUBE 1X as GPO3/fault output will not work then.

  • In addition to rising edge of GPI4, also rising edge on Enable will clear fault state. In standard mode Enable input will not clear faults.
  • GPO3 (fault state) output will go logic low after Enable signal goes low. In standard mode GPO3 stays high until faults are cleared.
  • GPO3 is open drain output to allow Wired and connection of multiple fault outputs of multiple drives
SimuCUBE Mode for SimuCUBE motherboard for force feedback simulator systems.
  • STO2 input acts as Enable and Clear faults input. In other words STO2 is the only one needed for all three functions, and Enable and Clear faults can be left unconnected.
  • Regenerative resistor drive has been tuned for SimuCUBE regenerative resistor
  • Power consumption limit has been tuned for simulator use (smoother operation than in other modes)
  • GPO5 is used as temperature controlled fan PWM output

Selecting device address[edit | edit source]

When accessing drive through SimpleMotion V2 bus, each device in the bus should be assigned to different address between 1 to N. Device address is a sum of hardware setting and software parameter SimpleMotion bus address offsetSMO. The address of device is determined at the moment of logic voltage power on and will become by sum of hardware setting and SMO.

Hardware setting is set by connecting a resistor between ADDRSELx and GND by method defined in article IONI SimpleMotion address selection (ADDRSEL).

Software selecting address[edit | edit source]

When having more than four devices in the same bus, or for example chaining multiple IONICUBE 1X motherboards (where all of them have address 1), it is necessary to utilize software parameter SimpleMotion bus address offsetSMO. Procedure for setting unique address for each device with SMO:

  1. Disconnect or unpower all other devices that the ones with already unique address (i.e. have only one IONICUBE connected to SM bus, or powered on)
  2. Connect to drive with Granity
  3. Adjust SMO parameter value so that device will receive a desired bus address. I.e. if using IONICUBE 1X, set SMO values 0, 1, 2, 3 to the different drives (drive addresses will become 1, 2, 3, 4). Or when IONICUBE (4 axis) is being used, set SMO values of drives on the first board 0, second board 4, third 8 etc (drive addresses will become 1 - 12).
  4. Save settings, disconnect and repeat the procedure for all drives.

Set-up overviews & first connection[edit | edit source]

This is the official and latest setup guide of IONI Servo Drive and IONICUBE motherboards. Read it through before installing or operating IONI series devices.
Ionicube4xfinal1260w.jpg

Setup process overview[edit | edit source]

Read trough the guide by following the outline on the top right side of the page and follow the hyper links to subtopics provided in the articles.

Ioni step1 collectthings.png

Read the page List of things needed for details.


Ioni step2 granityconnection.png

Connect drive to PC with SimpleMotion V2 USB adapter and Granity to test connection, upgrade firmware if necessary and to learn Granity. If you're already familiar with all this, you may skip this step. Read the article Making the first Granity connection.


Ioni step3 wiring.png

Carefully do the full wiring of the servo system. Consult an qualified electrician if necessary as dangerous voltages will be present. Before powering up, triple check everything by using multimeter to find short circuits. Read the main article Wiring.


Step4 tuningbaremotor.png

Power-up the system and connect again with Granity. Now set-up the motor to work as intended. See the main article Drive parameterization. If you already have a working configuration to your motor model, you may just load the settings file to the drive.


Step5 tuningmachine.png

After motor and drive are fully functional, connect motor to the mechanical load and find the optimum velocity or position control gains. Read the main article Servo motor tuning guide.

Troubleshooting[edit | edit source]

In case of troubles, refer to the articles in general troubleshooting category and IONI troubleshooting category.



List of items needed[edit | edit source]

The list of necessary things to build a working servo system with IONI
Optional but highly recommended items
  • Emergency stop button (normally closed NC type) or equivalent
Needed for high current motors (>5A average)
  • A cooling fan
Tools needed
  • Screwdrivers
  • Wire cutter
Skills needed
  • Qualified electrician skills
  • Basic knowledge of servo systems



Making the first Granity connection[edit | edit source]

Follow the instructions to make the first Granity connection to IONI drive.

Preparations[edit | edit source]

  1. Download and install the Granity software. Latest version can be downloaded from the link: Granity software for windows (approx 18 MB)
  2. Make a wiring similar to the image below
    • With IONICUBE 4X revision 008 and lower, make sure that in the pinheader JP10 only position 1 has a jumper as depicted.
    • With IONICUBE 4X revision 009 and higher, make sure that the switch S1 position 1 is ON and position 4 (DFU mode) is OFF.
    • If you use a USB cable to connect (r. 009 and higher), turn also S1 position 2 and 3 ON.
  3. Connect IONICUBE to a PC
  4. Power up the 24 VDC power. Leds at the back of the IONI drive should start blinking (more about blinking sequences).
  5. Launch Granity software and:
    1. Go to Connect tab
    2. Ensure that "SimpleMotion V2 Adapter" is selected from dropdown menu called Communication interface device. (note 1)
    3. Click Connect to drive
    4. Once list of connected drives pop up, select the one you connected and click Open

Now if everything has gone well, you should see information about the drive model and serial number on the "Connect tab". Connection has been successfully tested and drive may be disconnected to proceed with next setup step.

Note 1) If multiple choices are named as "SimpleMotion V2 Adapter", then try each of them to find the correct one. Also if no adapters are found, try launching Granity software again as the list of adapter choices are updated only at program start-up.

IONICUBE Revision 1-8 (with jumpers)[edit | edit source]

Ionicube granity minimum.png

Minimum connection for Granity

IONICUBE Revision 9 and later (with DIP switch)[edit | edit source]

Ionicube 009 dip switch detail.png

SM Bus termination switch position for IONICUBE revision 009 and higher. For typical single IONICUBE wiring, set switches 1-3 to ON position and 4th OFF position.

More information about the termination and biasing of the RS485 serial bus here: Wikipedia:RS-485.




Wiring overwiew[edit | edit source]

IONICUBE connectors[edit | edit source]

X1
Dual port RJ45 connector with SimpleMotion V2 interface. For pinout, seeSimpleMotion V2 port.
X2
6 pin wire terminal for logic voltage supply, Safe torque off input, analog output and relay driver outputs.
X3
Two pin wire terminal for HV DC bus supply.
X4
Main control and setpoint signal port consisting Enable input signal, Fault output signal, pulse and direction/quadrature/PWM setpoint inputs and digital outputs for home switch status. X4 is directly wired to conform most common parallel port style pulse & direction CNC controllers.
X5
Second control and setpoint signal port. This port consists analog setpoint signal inputs and additional digital I/O.
X6
These are the feedback device connector for X (lower) and Y (upper) axis motors
X7
These are the power and holding brake output connector for X (lower) and Y (upper) axis motors
X8
These are the feedback device connector for Z (lower) and A (upper) axis motors
X9
These are the power and holding brake output connector for Z (lower) and A (upper) axis motors
X10
A connector for an optional external regenerative resistor. IONICUBE has on-board regenerative resistor that is sufficient for most installations.
IONI_X, IONI_Y, IONI_Z, IONI_A
Card-edge connectors for IONI drives

Front side connectors[edit | edit source]

Front side connectors consist X6, X7, X8 and X9. These connectors are the interface towards motors (motor power and feedback devices).

Ionicubelayout.png

Connector layout and naming. View from top of the board.

Ionicube revision 3 layout.png

IONICUBE revision 3 PCB layout. USB connector X11 and Switch S1 to replace the jumper header.

Ioni motoroutouts per drive.png

Power and feedback ports of X, Y, Z and A axis. View from plug side of the board.


Ionicubemotorconnectors.png

Names of power and feedback ports. I.e. X9A means upper floor connector of X9 and X9B the lower floor of X9. View from plug side of the board.

Legend[edit | edit source]

Color
Supply pin
Input pin
Output pin

X7 and X9 pinout[edit | edit source]

These are the power output and holding brake output connector for motors

Pin number Signal name AC/BLDC motor Brush DC motor Stepping motor
1 GND Ground for cable shield and an optional motor holding brake coil
2 PHASE1 U (some motors R) Armature + Coil A.1
3 PHASE2 V (some motors S) Armature - Coil A.2
4 PHASE3 W (some motors T) Armature - Coil B.1
5 PHASE4 Not connected Armature + Coil B.2
6 BRAKE Optional 24V motor holding brake coil

Motor & brake wiring schematics[edit | edit source]

X6 and X8 pinout[edit | edit source]

X6 and X8 are the feedback device connectors of motors

Pin # Pin name Electrical type (in most feedback device modes) Quadrature encoder SinCos encoder BiSS-C encoder SSI encoder AMS SSI encoder
Shell GND Earth/case
1 HALL_W Hall sensor digital input, phase W - - -
2 HALL_V Hall sensor digital input, phase V - - -
3 HALL_U Hall sensor digital input, phase U - - -
4 GND Encoder supply ground
5 B- Differential input B- Channel B- SinCos input B- - - -
6 B+ Differential input B+ Channel B+ SinCos input B+ - - -
7 A- Differential input A- Channel A- SinCos input A- - - -
8 A+ Differential input A+ Channel A+ SinCos input A+ - - -
9 5V_OUT Encoder supply 5V output
10 GND Encoder supply ground
11 GPI3 Axis negative direction end limit switch (optional). Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Limit switch polarityLSP.
Clock/MA- Clock- CLK
12 GPI2 Axis positive direction end limit switch (optional).Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Limit switch polarityLSP.
Clock/MA+ Clock+ CSn
13 GPI1 Axis home switch switch (optional). Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Home switch or hard stop search direction (Home switch polarity)HMS.
DO
14 C- Differential input C- Index channel Z- Index channel Z+ Data/SLO- Data- -
15 C+ Differential input C+ Index channel Z+ Index channel Z+ Data/SLO+ Data+ -
Pin layout Female D-sub 15 connector as it appears from outside of drive. Note: counterpart (male) connector has mirrored pin layout if viewed from pin side, and same layout if viewed from soldering side.

D15 pinout.png

Examples of feedback device and switch wiring[edit | edit source]


Back side connectors[edit | edit source]

Ionicube x2345.png

A closeup of X2, X3, X4 and X5


X2 pinout[edit | edit source]

X2 is 6 pin wire terminal for logic voltage supply, Safe torque off input, analog output and relay driver outputs.

Pin number Signal name Usage
1 GND Ground
2 24V 24V logic supply
3 STO Safe torque off input (this pin also available in X1, as defined in SimpleMotion V2 port
4 VFD 0-12V analog output where voltage level is proportional to PWM duty cycle on pin PWM on X4. PWM frequency must be between 100 and 10000 Hz.
5 RL1 Relay coil driver output 1. When RLIN1 on X4 is logic high, RL1 is pulled to GND by an open collector circuit. When RLIN1 is low, RL1 is floating (max 24V). When connecting a relay that has 24VDC coil between RL1 and supplied 24V, no external free-wheeling diode is needed. Output current rating is max 500 mA.
6 RL2 Relay coil driver output 2. When RLIN2 on X4 is logic high, RL2 is pulled to GND by an open collector circuit. When RLIN1 is low, RL2 is floating (max 24V). When connecting a relay that has 24VDC coil between RL2 and supplied 24V, no external free-wheeling diode is needed. Output current rating is max 500 mA.

X3 pinout[edit | edit source]

X3 is two pin wire terminal for HV DC bus supply.

Pin number Signal name Usage
1 GND Ground
2 HV+ Motor power supply, HV DC bus (see IONI drive voltage range spec)

See also:

X4 pinout[edit | edit source]

X4 is main control and setpoint signal port consisting Enable input signal, Fault output signal, pulse and direction/quadrature/PWM setpoint inputs and digital outputs for home switch status. X4 is directly wired to conform most common parallel port style pulse & direction CNC controllers.

Pin number in header Pin number in D25 cable Signal name Typical usage Pin number in header Pin number in D25 cable Signal name Typical usage
1 1 ENABLE Enable all axis (with or without chargepump) 2 14 PWM PWM input for VFD analog output
3 2 HSIN1_X Pulse/step input X 4 15 GPO4_A Limit switch output A
5 3 HSIN2_X Direction input X 6 16 RLIN1 Controls RL1 state
7 4 HSIN1_Y Pulse/step input Y 8 17 RLIN2 Controls RL2 state
9 5 HSIN2_Y Direction input Y 10 18 GND Ground
11 6 HSIN1_Z Pulse/step input Z 12 19 GND
13 7 HSIN2_Z Direction input Z 14 20 GND
15 8 HSIN1_A Pulse/step input A 16 21 GND
17 9 HSIN2_A Direction input A 18 22 GND
19 10 STOP_OUT Fault on any axis or E-stop (active low). Note: this is IONI's GPO3 signals connected in parallel between all axis / wired-or configuration. 20 23 GND
21 11 GPO4_X Limit switch output X 22 24 GND
23 12 GPO4_Y Limit switch output Y 24 25 GND
25 13 GPO4_Z Limit switch output Z 26 N/A Not connected
Pin layout 26 pin header pinout.png

Alternative setpoint signals[edit | edit source]

Setpoint mode is selected by software with parameter Setpoint inputCRI and behavior is affected by parameters Setpoint smoothingCIS, Setpoint multiplierMUL, Setpoint dividerDIV, Setpoint offset nullingCAO and Enable direction inputCED.

Signal name Function Used for Remarks
HSIN1 High speed digital input 1 Depending on setpoint mode, can be either:
HSIN2 High speed digital input 2 Depending on setpoint mode, can be either:
  • Direction signal of pulse train (in Pulse and direction setpoint mode)
  • Quadrature B channel (in quadrature setpoint mode)
  • PWM (in PWM and PWM+Dir setpoint modes)
ANAIN- Differential analog negative input Used for analog setpoint mode Setpoint voltage is the voltage difference between ANAIN+ and ANAIN-
ANAIN+ Differential analog positive input Used for analog setpoint mode

X5 pinout[edit | edit source]

X5 is a second control and setpoint signal port in addition to X4. This port consists analog setpoint signal inputs and additional digital I/O.

Pin number in header Pin number in D25 cable Signal name Typical usage Pin number in header Pin number in D25 cable Signal name Typical usage
1 1 GND 2 14 +5V_OUT 5V supply from IONICUBE ^2
3 2 ANAIN-_X +/-10V analog input X 4 15 ANAIN+_X +/-10V analog input X
5 3 ANAIN-_Y +/-10V analog input Y 6 16 ANAIN+_Y +/-10V analog input Y
7 4 ANAIN-_Z +/-10V analog input Z 8 17 ANAIN+_Z +/-10V analog input Z
9 5 ANAIN-_A +/-10V analog input A 10 18 ANAIN+_A +/-10V analog input A
11 6 GPO1_X For pin function, refer to IONI connector pinout 12 19 GPI4_X For pin function, refer to IONI connector pinout
13 7 GPO1_Y 14 20 GPI4_Y
15 8 GPO1_Z 16 21 GPI4_Z
17 9 GPO1_A 18 22 GPI4_A
19 10 GPO5_X 20 23 GPI5_X
21 11 GPO5_Y 22 24 GPI5_Y
23 12 GPO5_Z 24 25 GPI5_Z
25 13 GPO5_A 26 N/A GPI5_A
Pin layout 26 pin header pinout.png

Application example[edit | edit source]

Follwing image shows typical installation schemes for pulse/direction controlled systems, typically found in PC CNC applications.




IONICUBE 4X wiring[edit | edit source]

IONICUBE connectors[edit | edit source]

X1
Dual port RJ45 connector with SimpleMotion V2 interface. For pinout, seeSimpleMotion V2 port.
X2
6 pin wire terminal for logic voltage supply, Safe torque off input, analog output and relay driver outputs.
X3
Two pin wire terminal for HV DC bus supply.
X4
Main control and setpoint signal port consisting Enable input signal, Fault output signal, pulse and direction/quadrature/PWM setpoint inputs and digital outputs for home switch status. X4 is directly wired to conform most common parallel port style pulse & direction CNC controllers.
X5
Second control and setpoint signal port. This port consists analog setpoint signal inputs and additional digital I/O.
X6
These are the feedback device connector for X (lower) and Y (upper) axis motors
X7
These are the power and holding brake output connector for X (lower) and Y (upper) axis motors
X8
These are the feedback device connector for Z (lower) and A (upper) axis motors
X9
These are the power and holding brake output connector for Z (lower) and A (upper) axis motors
X10
A connector for an optional external regenerative resistor. IONICUBE has on-board regenerative resistor that is sufficient for most installations.
IONI_X, IONI_Y, IONI_Z, IONI_A
Card-edge connectors for IONI drives

Front side connectors[edit | edit source]

Front side connectors consist X6, X7, X8 and X9. These connectors are the interface towards motors (motor power and feedback devices).

Ionicubelayout.png

Connector layout and naming. View from top of the board.

Ionicube revision 3 layout.png

IONICUBE revision 3 PCB layout. USB connector X11 and Switch S1 to replace the jumper header.

Ioni motoroutouts per drive.png

Power and feedback ports of X, Y, Z and A axis. View from plug side of the board.


Ionicubemotorconnectors.png

Names of power and feedback ports. I.e. X9A means upper floor connector of X9 and X9B the lower floor of X9. View from plug side of the board.

Legend[edit | edit source]

Color
Supply pin
Input pin
Output pin

X7 and X9 pinout[edit | edit source]

These are the power output and holding brake output connector for motors

Pin number Signal name AC/BLDC motor Brush DC motor Stepping motor
1 GND Ground for cable shield and an optional motor holding brake coil
2 PHASE1 U (some motors R) Armature + Coil A.1
3 PHASE2 V (some motors S) Armature - Coil A.2
4 PHASE3 W (some motors T) Armature - Coil B.1
5 PHASE4 Not connected Armature + Coil B.2
6 BRAKE Optional 24V motor holding brake coil

Motor & brake wiring schematics[edit | edit source]

X6 and X8 pinout[edit | edit source]

X6 and X8 are the feedback device connectors of motors

Pin # Pin name Electrical type (in most feedback device modes) Quadrature encoder SinCos encoder BiSS-C encoder SSI encoder AMS SSI encoder
Shell GND Earth/case
1 HALL_W Hall sensor digital input, phase W - - -
2 HALL_V Hall sensor digital input, phase V - - -
3 HALL_U Hall sensor digital input, phase U - - -
4 GND Encoder supply ground
5 B- Differential input B- Channel B- SinCos input B- - - -
6 B+ Differential input B+ Channel B+ SinCos input B+ - - -
7 A- Differential input A- Channel A- SinCos input A- - - -
8 A+ Differential input A+ Channel A+ SinCos input A+ - - -
9 5V_OUT Encoder supply 5V output
10 GND Encoder supply ground
11 GPI3 Axis negative direction end limit switch (optional). Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Limit switch polarityLSP.
Clock/MA- Clock- CLK
12 GPI2 Axis positive direction end limit switch (optional).Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Limit switch polarityLSP.
Clock/MA+ Clock+ CSn
13 GPI1 Axis home switch switch (optional). Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Home switch or hard stop search direction (Home switch polarity)HMS.
DO
14 C- Differential input C- Index channel Z- Index channel Z+ Data/SLO- Data- -
15 C+ Differential input C+ Index channel Z+ Index channel Z+ Data/SLO+ Data+ -
Pin layout Female D-sub 15 connector as it appears from outside of drive. Note: counterpart (male) connector has mirrored pin layout if viewed from pin side, and same layout if viewed from soldering side.

D15 pinout.png

Examples of feedback device and switch wiring[edit | edit source]


Back side connectors[edit | edit source]

Ionicube x2345.png

A closeup of X2, X3, X4 and X5


X2 pinout[edit | edit source]

X2 is 6 pin wire terminal for logic voltage supply, Safe torque off input, analog output and relay driver outputs.

Pin number Signal name Usage
1 GND Ground
2 24V 24V logic supply
3 STO Safe torque off input (this pin also available in X1, as defined in SimpleMotion V2 port
4 VFD 0-12V analog output where voltage level is proportional to PWM duty cycle on pin PWM on X4. PWM frequency must be between 100 and 10000 Hz.
5 RL1 Relay coil driver output 1. When RLIN1 on X4 is logic high, RL1 is pulled to GND by an open collector circuit. When RLIN1 is low, RL1 is floating (max 24V). When connecting a relay that has 24VDC coil between RL1 and supplied 24V, no external free-wheeling diode is needed. Output current rating is max 500 mA.
6 RL2 Relay coil driver output 2. When RLIN2 on X4 is logic high, RL2 is pulled to GND by an open collector circuit. When RLIN1 is low, RL2 is floating (max 24V). When connecting a relay that has 24VDC coil between RL2 and supplied 24V, no external free-wheeling diode is needed. Output current rating is max 500 mA.

X3 pinout[edit | edit source]

X3 is two pin wire terminal for HV DC bus supply.

Pin number Signal name Usage
1 GND Ground
2 HV+ Motor power supply, HV DC bus (see IONI drive voltage range spec)

See also:

X4 pinout[edit | edit source]

X4 is main control and setpoint signal port consisting Enable input signal, Fault output signal, pulse and direction/quadrature/PWM setpoint inputs and digital outputs for home switch status. X4 is directly wired to conform most common parallel port style pulse & direction CNC controllers.

Pin number in header Pin number in D25 cable Signal name Typical usage Pin number in header Pin number in D25 cable Signal name Typical usage
1 1 ENABLE Enable all axis (with or without chargepump) 2 14 PWM PWM input for VFD analog output
3 2 HSIN1_X Pulse/step input X 4 15 GPO4_A Limit switch output A
5 3 HSIN2_X Direction input X 6 16 RLIN1 Controls RL1 state
7 4 HSIN1_Y Pulse/step input Y 8 17 RLIN2 Controls RL2 state
9 5 HSIN2_Y Direction input Y 10 18 GND Ground
11 6 HSIN1_Z Pulse/step input Z 12 19 GND
13 7 HSIN2_Z Direction input Z 14 20 GND
15 8 HSIN1_A Pulse/step input A 16 21 GND
17 9 HSIN2_A Direction input A 18 22 GND
19 10 STOP_OUT Fault on any axis or E-stop (active low). Note: this is IONI's GPO3 signals connected in parallel between all axis / wired-or configuration. 20 23 GND
21 11 GPO4_X Limit switch output X 22 24 GND
23 12 GPO4_Y Limit switch output Y 24 25 GND
25 13 GPO4_Z Limit switch output Z 26 N/A Not connected
Pin layout 26 pin header pinout.png

Alternative setpoint signals[edit | edit source]

Setpoint mode is selected by software with parameter Setpoint inputCRI and behavior is affected by parameters Setpoint smoothingCIS, Setpoint multiplierMUL, Setpoint dividerDIV, Setpoint offset nullingCAO and Enable direction inputCED.

Signal name Function Used for Remarks
HSIN1 High speed digital input 1 Depending on setpoint mode, can be either:
HSIN2 High speed digital input 2 Depending on setpoint mode, can be either:
  • Direction signal of pulse train (in Pulse and direction setpoint mode)
  • Quadrature B channel (in quadrature setpoint mode)
  • PWM (in PWM and PWM+Dir setpoint modes)
ANAIN- Differential analog negative input Used for analog setpoint mode Setpoint voltage is the voltage difference between ANAIN+ and ANAIN-
ANAIN+ Differential analog positive input Used for analog setpoint mode

X5 pinout[edit | edit source]

X5 is a second control and setpoint signal port in addition to X4. This port consists analog setpoint signal inputs and additional digital I/O.

Pin number in header Pin number in D25 cable Signal name Typical usage Pin number in header Pin number in D25 cable Signal name Typical usage
1 1 GND 2 14 +5V_OUT 5V supply from IONICUBE ^2
3 2 ANAIN-_X +/-10V analog input X 4 15 ANAIN+_X +/-10V analog input X
5 3 ANAIN-_Y +/-10V analog input Y 6 16 ANAIN+_Y +/-10V analog input Y
7 4 ANAIN-_Z +/-10V analog input Z 8 17 ANAIN+_Z +/-10V analog input Z
9 5 ANAIN-_A +/-10V analog input A 10 18 ANAIN+_A +/-10V analog input A
11 6 GPO1_X For pin function, refer to IONI connector pinout 12 19 GPI4_X For pin function, refer to IONI connector pinout
13 7 GPO1_Y 14 20 GPI4_Y
15 8 GPO1_Z 16 21 GPI4_Z
17 9 GPO1_A 18 22 GPI4_A
19 10 GPO5_X 20 23 GPI5_X
21 11 GPO5_Y 22 24 GPI5_Y
23 12 GPO5_Z 24 25 GPI5_Z
25 13 GPO5_A 26 N/A GPI5_A
Pin layout 26 pin header pinout.png

Application example[edit | edit source]

Follwing image shows typical installation schemes for pulse/direction controlled systems, typically found in PC CNC applications.

IONICUBE 1X wiring[edit | edit source]

IONICUBE 1X connectors[edit | edit source]

X1.1 and X1.2
RJ45 connector with SimpleMotion V2 interface. For pinout, seeSimpleMotion V2 port.
X2
feedback device connector for motor
X3
9 pin wire terminal for HV DC bus supply, logic voltage supply, regenerative resistor and motor power output.
X4
Control and setpoint signal port. Contains also output for motor solenoid holding brake.
X5
Card-edge connectors for IONI drive

IONICUBE 1X connectors[edit | edit source]

Ionicube1x pinouts.png

Connector layout and naming


Ionicube1x wiring.png

Wiring overview. R is regenerative resistor and E is encoder. In minimum working connection, wire 5V voltage to ENABLE and STO2 inputs into X4 pins (these two signals allow drive to be operated). Note: STO2 accepts voltage from 4.5 to 25 VDC but other digital inputs, such as ENABLE only between 2.7 to 5.5VDC.

Legend[edit | edit source]

Color
Supply pin
Input pin
Output pin

X3 pinout[edit | edit source]

This is a wire terminal connector for power input and output

Pin number Signal name Usage
1 GND Ground
2 HV+ Motor power supply, HV DC bus (see IONI drive voltage range spec)
3 VCC 24V logic supply
4 PH1 (PHASE1) Motor phase 1 (see wiring table below)
5 PH2 (PHASE2) Motor phase 2 (see wiring table below)
6 PH3 (PHASE3) Motor phase 3 (see wiring table below)
7 PH4 (PHASE4) Motor phase 4 (see wiring table below)
8 REG Regenerative resistor output
9 GND Ground
Pin number Signal name AC/BLDC motor Brush DC motor Stepping motor
1 GND Ground for cable shield and an optional motor holding brake coil
4 PHASE1 U (some motors R) Armature + Coil A.1
5 PHASE2 V (some motors S) Armature - Coil A.2
6 PHASE3 W (some motors T) Armature - Coil B.1
7 PHASE4 Not connected Armature + Coil B.2

Motor & brake wiring schematics[edit | edit source]

Note: the images below are drawn for IONICUBE 4 axis version. IONICUBE 1X wiring is equivalent except there is no brake output in the X3. Brake output pin is located in X4.

Regenerative resistor[edit | edit source]

Regenerative resistor is optional and may be connected between REG and HV+ terminals. The on board transistor is capable of carrying max 10 Amp current on regenerative resistor, so minimum allowed resistance can be calculated from: Rmin=HVvoltage/10. I.e. with 48VDC HV supply, the minimum resistance is 48V/10A = 4.8 Ohms. Suggested resistor power capability is 20-100 W.

X2 pinout[edit | edit source]

X2 is the feedback device connector of motor

Pin # Pin name Electrical type (in most feedback device modes) Quadrature encoder SinCos encoder BiSS-C encoder SSI encoder AMS SSI encoder
Shell GND Earth/case
1 HALL_W Hall sensor digital input, phase W - - -
2 HALL_V Hall sensor digital input, phase V - - -
3 HALL_U Hall sensor digital input, phase U - - -
4 GND Encoder supply ground
5 B- Differential input B- Channel B- SinCos input B- - - -
6 B+ Differential input B+ Channel B+ SinCos input B+ - - -
7 A- Differential input A- Channel A- SinCos input A- - - -
8 A+ Differential input A+ Channel A+ SinCos input A+ - - -
9 5V_OUT Encoder supply 5V output
10 GND Encoder supply ground
11 GPI3 Axis negative direction end limit switch (optional). Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Limit switch polarityLSP.
Clock/MA- Clock- CLK
12 GPI2 Axis positive direction end limit switch (optional).Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Limit switch polarityLSP.
Clock/MA+ Clock+ CSn
13 GPI1 Axis home switch switch (optional). Normally closed (NC) switch is highly recommended for safety reasons.
Connect it between this pin and GND pin. Normally open (NO) switch can be used, and the switch polarity can be changed with Home switch or hard stop search direction (Home switch polarity)HMS.
DO
14 C- Differential input C- Index channel Z- Index channel Z+ Data/SLO- Data- -
15 C+ Differential input C+ Index channel Z+ Index channel Z+ Data/SLO+ Data+ -
Pin layout Female D-sub 15 connector as it appears from outside of drive. Note: counterpart (male) connector has mirrored pin layout if viewed from pin side, and same layout if viewed from soldering side.

D15 pinout.png

Examples of feedback device and switch wiring[edit | edit source]


X4 pinout[edit | edit source]

X4 is main control and setpoint signal port consisting Enable input signal, Fault output signal, pulse and direction/quadrature/PWM setpoint inputs and digital outputs for home switch status. X4 is directly wired to conform most common parallel port style pulse & direction CNC controllers.

Pin number in header Signal name Typical usage Signal name Typical usage
1 GND Ground 2 5V_OUT 5V output for optional external circuity
3 HSIN2 Depending on setpoint mode, can be either:
  • Direction signal of pulse train (in Pulse and direction setpoint mode)
  • Quadrature B channel (in quadrature setpoint mode)
  • PWM (in PWM and PWM+Dir setpoint modes)
4 HSIN1 Depending on setpoint mode, can be either:
5 ANAIN+ +/-10V analog setpoint input2 6 ANAIN- +/-10V analog setpoint input2
7 GPI2 Enable positive feed (also in X2)1 8 GPI1 Home switch input (also in X2)1
9 GPI4 Clear faults1 10 GPI3 Enable negative feed (also in X2)1
11 REGEN_OUT Regenerative resistor power switch state (redundant, IONICUBE 1X has internal power switch) 12 GPI5 Start homing1
13 MECH_BRAKE_OUT Mechanical holding brake output3 14 GPO5 Reserved for future use1
15 GPO4 Limit switch output 16 GPO3 Fault on any axis or E-stop (active low)1
17 GPO2 Tracking error warning1 18 GPO1 Servo ready1
19 STO2 Safe torque off input (this pin also present in X14) 20 ENABLE Enable drive (with or without chargepump) (this pin also present in X14)

1) For detailed pin function and alternative functions in various modes, refer to IONI connector pinout

2) Setpoint voltage is measured from the difference of voltage potentials between ANAIN+ and ANAIN-. Both ANAIN inputs must always lie within +/-12V from GND (meaning that controller's zero voltage reference, i.e. GND must be connected to the GND if drive to prevent voltage potentials from floating.

3) This output can directly drive a 24V solenoid brake (max 500mA) if VCC is supplied by 24 volts. In such case, connect brake wires between MECH_BRAKE_OUT and VCC.

4) The same pin is routed also to X1 connectors. Use ENABLE/STO2 pins of only either X4 or X1, not both.


X1 connector[edit | edit source]

X1 connectors are for SimpleMotion V2 bus which is used for drive configuration with Granity software and control over a multidrop capable serial data link. For pinout, see SimpleMotion V2 port.


DIP Switch S1 settings[edit | edit source]

On board switch S1 controls the SM bus termination. Set switch 1 to ON position if the IONICUBE 1X devie is the only device in a SM bus OR if it's the last device in device chain. All other cases, leave it OFF (in other words, if IONICUBE is chained to multiple SM bus devices and it's not the last device of the chain).

Using 24 Volt control signals[edit | edit source]

As many industrial environments use 24V signaling for logic, interfacing IONICUBE 1X has been designed to accept these voltages with help of external circuits:

  • The GPOx outputs are NPN open collector type the pulling pin to GND when output is logic 1. GPO can be loaded up to same voltage level with logic supply voltage.
    • If 24V logic accepts such NPN open collector output, wire directly
    • If push/pull type output is needed, wire a pull-up resistor (i.e. 2200 Ohm or higher) between GPOx and 24V voltage
  • Inputs are routed directly to IONI input pins that accept up to 5V directly. To extend the range, add a resistor divider network to reduce the voltage to accepted level. I.e. on each pin:
    • 470 Ohm resistor from GPIx to GND, and
    • 2200 Ohm GPIx to user 24V input signal
    • That two-resistor circuit will reduce 24V level logic 1 to an acceptable ~4.2V level, while logic 0 will be ~0V.

Dimensions and mounting[edit | edit source]

IONICUBE 1X can be mounted by screws to a base or with optional DIN rail clips to a standard DIN rail.

To mount in DIN rail, obtain 2 pcs of Phoenix Contact part number 1201578. Such part is available from many distributors including Digikey 277-2296-ND

Ionicube1x dims.png

Dimensions and mounting hole locations

.

Mating connectors and accessories[edit | edit source]

Warning: Display title "IONI Mating connectors and accessories for IONI & IONICUBE" overrides earlier display title "IONI IONI & IONICUBE wiring (4 axis IONICUBE)".

This page lists examples of available mating connectors, accessories and spare parts for IONI drive together with IONICUBE four axis motherboard. Most parts or equivalents are available from large number of distributors. You may use http://www.findchips.com/ to search the same or similar parts from alternative distributors.

Recommended shopping list[edit | edit source]

  • Connectors and backshells for X6/X8 unless using a motor with pre-made encoder cables (like Granite Devices servo motors)
  • X1 cable (RJ45 cable)
  • X4/X5 connectors and flat cable
    • A flat cable to D-Sub 25 connector if direct connection to parallel port based PC CNC software is desired
  • EMI filters
  • 24 VDC logic power supply
  • HV DC bus power supply

See the list of example parts below.

Connectors[edit | edit source]

X6 & X8 connector[edit | edit source]

Description Manufacturer Part number Distributors and order codes
PLUG, D, SOLDER, 15WAY MULTICOMP 5501-15PA-02-F1

Accessories[edit | edit source]

Description Manufacturer Part number Distributors and order codes
D-SUB BACKSHELL, 15WAY MH CONNECTORS DPPK15-GREY-K

X1 connector[edit | edit source]

Cable assemblies[edit | edit source]

Cable used for X1 should be shielded (S/FTP or FTP, not UTP) type.

Description Manufacturer Part number Distributors and order codes
Premium patch cable 0.5m VIDEK 3962-0.5 Farnell 1525999
Premium patch cable 1m VIDEK 3962-1
Premium patch cable 2m VIDEK 3962-2 Farnell 1525753
Premium patch cable 5m VIDEK 3962-5 Farnell 1525755
Premium patch cable 10m VIDEK 3962-10
Shielded patch cable 0.5m VIDEK 2992-0.5 Farnell 1517504
Shielded patch cable 1m VIDEK 2992-1
Shielded Patch cable 2m VIDEK 2992-2 Farnell 1517506
Shielded patch cable 5m VIDEK 2992-5 Farnell 1517509
Shielded patch cable 10m VIDEK 2992-10
Shielded patch cable 0.5m Assman A-MCSP-80005/B-R Digikey A-MCSP-80005/B-R
Shielded patch cable 1m Assman A-MCSP-80005/Y-R Digikey A-MCSP-80010/Y-R
Shielded patch cable 2m Assman A-MCSP-80020/Y-R Digikey A-MCSP-80020/Y-R
Shielded patch cable 3m Assman A-MCSP-80050/Y-R Digikey A-MCSP-80030/Y-R
Shielded patch cable 5m Assman A-MCSP-80050/Y-R Digikey A-MCSP-80050/Y-R
Shielded patch cable 10m Assman A-MCSP-80050/Y-R Digikey A-MCSP-80100/Y-R

Accessories[edit | edit source]

Description Manufacturer Part number Distributors and order codes
RJ45 break-out board with DIN rail fixture (convert RJ45 to screw terminals). Helpful for wiring STO and Enable wires. Camden boss CIM/RJ45 Farnell 2211819

X7 and X9 connector[edit | edit source]

These parts are included with IONICUBE 4 axis product.

Description Manufacturer Part number Distributors and order codes
6 pole 5mm pitch terminal plug FCI 20020007-G061B01LF

X4 and X5 connector[edit | edit source]

Example of DIN rail attachable IDC terminal block/breakout board.

Mating connector type is 0.1" pitch 26 pin IDC ribbon cable socket, see example (pdf).

Description Manufacturer Part number Distributors and order codes
SOCKET, IDC, 2.54MM, 26WAY AMPHENOL T812126A100CEU
SOCKET, IDC, WITH S/RELIEF, 26WAY MULTICOMP MC6FD026-30P1
FLAT CABLE 26 WAY 3M 3302/26 300SF Digikey MC26M-5-ND

Accessories[edit | edit source]

Description Manufacturer Part number Distributors and order codes
IDC terminal block, 26WAY Camden boss CIM/202426W-IDCS
FLAT CABLE TO D-SUB 25 CONNECTOR Sullins SDS103-PRW2-M25-SN00-211 Digikey S9577-ND

Electromagnetic interference filtering[edit | edit source]

Description Manufacturer Part number Distributors and order codes
EMI suppression core for low frequency band Laird LFB159079-000 Digikey 240-2281-ND
EMI suppression core for medium frequency band Laird 28B0616-000 Digikey 240-2306-ND

Power supplies[edit | edit source]

Before making decision on power supplies, see:

24V low power logic supply[edit | edit source]

Description Manufacturer Part number Distributors and order codes
24 VDC power supply TDK-Lambda LS35-24 Digikey 285-1893-ND
24 VDC DIN rail power supply CUI Inc VDRS-20-24 Digikey 102-2152-ND

HV DC high power motor supply[edit | edit source]

Voltage Power Manufacturer Part number Distributors and order codes
24 VDC 150 W Delta Electronics PMT-24V150W1AA Digikey 1145-1075-ND
24 VDC 200 W Delta Electronics PMT-24V200W1AM Digikey 1145-1076-ND
Voltage Power Notes ! Manufacturer Part number Distributors and order codes
48 VDC 150 W Delta Electronics PMT-48V150W1AA Digikey 1145-1109-ND
48 VDC 200 W TDK-Lambda LS200-48 Digikey 285-1982-ND
48 VDC 300 W TDK-Lambda RWS300B48 Digikey 285-2294-ND
48 VDC 320 W Mean Well RSP-320-48 Granite Devices Store RSP-320-48

Findchips RSP-320-48

48 VDC 480 W DIN rail mounting Mean Well NDR-480-48 Granite Devices Store NDR-480-48

Mouser NDR-480-48

48 VDC 480 W 720 W peak output power capability, DIN rail mounting Mean Well SDR-480-48 Mouser SDR-480-48
48 VDC 480 W Requires 3 phase AC power XP Power DNR480PS48-I Digikey 1470-1102-ND

Farnell 1372704

48 VDC 450 W Not CE compliant (EU) Mean Well SE-450-48 Findchips SE-450-48
48 VDC 480 W Delta Electronics DRP048V480W1BN Digikey 1145-1094-ND
48 VDC 600 W Not CE compliant (EU) Mean Well SE-600-48 Findchips SE-600-48
48 VDC 600 W TDK-Lambda RWS600B48 Digikey 285-2298-ND
48 VDC 960 W Requires 3 phase AC power XP Power DNR960TS48-I Digikey 1470-3050-ND

Farnell 1634807

48 VDC 1000 W XP Power SHP1000PS48 Digikey 1470-2226-ND



Status LED indicators[edit | edit source]

Warning: Display title "IONI LED indicators" overrides earlier display title "IONI Mating connectors and accessories for IONI & IONICUBE".
IONI has two on-board led indicators which have dedicated indicating tasks:
  • LED1 Motor control state indicator (green)
  • LED2 Fault indicator (orange)

How to read indications[edit | edit source]

  • LED1 and LED2 have programmed blinking sequences. Sequences consists series of short (S) and long (L) light pulses. For example LLS means the led will blink two long flashs and then one short flash. After sequence there will be a pause before the sequence repeats.
  • LED1 and LED2 are independent and can show fault and motor state simultaneously. To easier reading sequence, cover one led with a thumb to be able to concentrate to one led.
  • LED2 and shows the first fault occurred if multiple fault states are active simultaneously.
  • LED1 and LED2 are flashing together if device is in a firmware upgrade mode (DFU).

List of all LED1 and LED2 sequences[edit | edit source]

To see animated images, view this Wiki page in a web browser with animations enabled. The animations show Argon front panel, but the blinking sequences of IONI are equivalent when LED1=LD4 and LED2=LD3.

Faults[edit | edit source]

Only LED2 is being controlled by these faults, except in DFU mode when both leds blink together.

Fault reason LED sequence LED sequence as text
Hardware 3LLSS.gif LLSS
Progral or memory 3LSLL.gif LSLL
Internal comm error (CRC) 3LSL.gif LSL
Initialization 3LSS.gif LSS
Over current 3SLL.gif SLL
Over temperature 3LSLS.gif LSLS
Over voltage 3SLS.gif SLS
Following error 3LS.gif LS
Under voltage 3SL.gif SL
Motion blocked or motor runaway 3SLL.gif SSL
Setpoint range exceeded 3LSSL.gif LSSL
SimpleMotion communication error 3LSSS.gif LSSS
Other/unknown, possibly configuration error such as motor mode Motor typeMT not selected 3SSSL.gif SSSL

Motor control states[edit | edit source]

Only LED1 is being controlled by these states.

Status LED sequence LED sequence as text Motor output powered
Permanent stop (need device reset) 4LLS.gif LLS No
Fault stop (observe LD3 for reason) 4OFF.gif Off Depends on fault
Follow error recovery motion 4LS.gif LS Yes
Initializing 4SL.gif SL Yes
Homing 4LSS.gif LSS Yes
Run 4ON.gif On yes
Drive disabled (enable signal/command missing) OR other/uncategorized (not any of above). For clarity, connect with Granity and see status bits. 4LLSS.gif LLSS Yes or No

IONICUBE LED indicators[edit | edit source]

IONICUBE has four LED indicators that will are dedicated to:

LED1
Power on (24V supplied)
LED2
GPO1_X (LED on when GPO1_X is high)
LED3
Fault stop state (LED on when any of drives has fault stop state on)
LED4
Regenerative resistor is being driven
Ionicubeleds.png

LED1-4 on IONICUBE



Drive parameterization[edit | edit source]

Warning: Display title "IONI parameterization" overrides earlier display title "IONI LED indicators".

This article will describe how to set-up IONI parameters with Granity to make motor operational and ready for servo tuning.

Preparations and connection[edit | edit source]

As the goal is to parameterize and make motor operational, we should have:

  1. The drive and motor fully wired. However it's not required to have controller or braking resistor connected at this point.
  2. Be familiar with the operation and parameters of Granity. Make sure you have read Granity user guide.
  3. Granity connection working. See IONI & IONICUBE user guide/Making the first Granity connection


Minimum setup for drive & motor configuration stages

Walk-through of initial parametrization[edit | edit source]

In this chapter we walk-trough all Granity tabs and modify the parameter needed. This guide assumes that the drive is in factory defaults state (not configured before). Restore drive to factory state can be done by uploading a firmware file to the drive.

Connect tab[edit | edit source]

No other actions than connect to drive needed on this tab. Once connection successful, proceed to the next tab.

Goals tab[edit | edit source]

The factory defaults (torque control as control mode and serial only as setpoint) as well as the other defaults are the correct ones for beginning.

Machine tab[edit | edit source]

In this tab we configure the motor and its feedback device.

Axis mechanics[edit | edit source]

Parameters Axis type & unitsAXT and Axis scaleAXS affect only on the unit conversion of Granity parameters (such as acceleration/velocity limit unit conversions) and has no effect on drive operation.

Choose your axis type and scale, or leave them as defaults.

Motor[edit | edit source]

Find motor parameters from the motor data sheet/manufacturer specifications.

  1. Choose motor type from the drown down list Motor typeMT. If motor is linear type, see configuring linear servo motor. If setting up a stepping motor instead of servo motor, see Using stepping motor with IONI.
  2. Set motor Pole countMPC (non-brush DC motors only). If unsure, see Determining motor pole count.
  3. Set Maximum speedMMS of the motor, or alternatively the maximum allowed motor speed in the target application
  4. Set motor Peak current limitMMC and Peak current limitMMC current values. If non-brush DC motor type has been selected, then these are measured as the peak value of sine. See Motor peak and continuous current limits for description.
  5. Set Thermal time constantMTC. Motor thermal time constant value in seconds, used for thermal modeling of motor to avoid motor overheating with Peak current limitMMC. If not available, use formula 200*motor_weight (kg) as approximate, so a 2 kg motor would get a 400 second time constant. There is no guarantee of accuracy of this method.
  6. Setting motor Coil resistanceMR and Coil inductanceML values are required for proper drive operation. Do this by using the Granity's measurement function after drive is enabled and operating the first time. If this method fails, perform Tuning torque controller manually after initial parameters are set or find motor inductance & resistance values from your motor data sheet.

Feedback device[edit | edit source]

  1. Choose feedback device type from the drop down Feedback deviceFBD
  2. Set feedback device resolution. If Feedback deviceFBD is quadrature encoder, then manufacturers typically give resolution as pulses per revolution (PPR) or lines per revolution (LPR) which are the same thing and shall be entered directly into Feedback device resolutionFBR field. Some manufactures also call PPR as CPR.
  3. Configure the polarity of feedback device counting direction by Invert feedback directionFBI parameter. Motor and feedback device must have same electrical positive rotation direction to make a stable servo system. If your system shows no stability (instant following error after a motor "jump"), try changing this setting.
  4. Leave the Hall sensors Off from parameter Hall sensorsFBH during initial setup. Enable later if necessary (see when).

Tuning[edit | edit source]

Tuning tab contains feedback gain values for velocity and position control modes as well as torque bandwidth limit setting. Configuring these parameters are documented in Servo motor tuning guide. However, before proceeding into tuning, go through all other settings listed in this article.

Fault limits[edit | edit source]

Fault limits define the conditions in which drive is willing to operate. If condition is out of the set values, drive will enter into a fault state and stop motor control until errors are cleared.

Drive fault limits[edit | edit source]

These settings specify drive electrical condition such as supply voltage and over current tolerance.

  1. Leave Over current toleranceFOC value as default if no overcurrent faults occur. See Tuning torque controller if overcurrent faults occur.
  2. Set Over voltage fault thresholdFOV following way depending on your HV DC bus supply voltage. Set FOV value at least 10% higher than nominal HV DC bus voltage. For detailed guide of understanding FUV and FOV parameters, see page Configuring drive voltage limits FUV and FOV. Examples:
    1. 24 VDC regulated power supply, try value of 32 VDC
    2. 48 VDC regulated power supply, try value of 54 VDC
  3. Set Under voltage fault thresholdFUV so that drive will not trigger undervoltage fault during varying load of HV DC bus. Example:
    1. 24 VDC regulated power supply, try value of 19 VDC
    2. 48 VDC regulated power supply, try value of 35 VDC
  1. It is important to goal deviation faults (i.e. Goal faults filter timeFFT, Position tracking error thresholdFPT, Velocity tracking error thresholdFVT, Over speed faultFEV) as low as possible. Set them so that faults don't occur during normal operation but any anomaly or unexpected behavior will trigger them.

Goal deviation faults[edit | edit source]

These faults adjust motor monitoring during operation. Drive will enter into fault state if motor condition deviates more than allowed from the desired condition. See Granity unit conversion before adjusting.

  1. Goal Goal faults filter timeFFT sets the time how fast Position tracking error thresholdFPT, Velocity tracking error thresholdFVT, Over speed faultFEV and Motion fault thresholdFMO faults react. Setting higher time value allows drive to continue operation over short deviations thus avoid false triggering. Set this from 0.0 to 0.2 seconds in the beginning.
  2. Set Position tracking error thresholdFPT according how much mechanical axis is allowed to deviate from the setpoint position in position control mode.
  3. Set Velocity tracking error thresholdFVT according how much motor or axis speed may may deviate from the velocity setpoint. This affects also in position mode as velocity controller is the intermediate step between torque and position controllers.
  4. Set Over speed faultFEV according to the maximum speed allowed for the motor or axis. Helps to stop motor if system goes totally out of control and speeds up spuriously.
  5. Leave Motion fault thresholdFMO as 0 (0 = disabled) for the beginning. Using nonzero value enables motion fault.
  6. Choose Limit switch functionLFS according to your preference. If other than Do nothing option requires that limit switches are installed and connected to J5 port. Note: at the moment Servo stop option is active in the drive firmware and will do nothing until FW upgrade enables it.

Testing tab[edit | edit source]

These settings does not affect drive operation, so nothing to be changed here at this point. These controls will be used for servo tuning purposes and fault analysis.

Enabling drive[edit | edit source]

In order to test any configuration you make, you need to set drive in enabled state. This involves that:

  1. Drive is powered on (logic & HV DC bus)
  2. Enable signal is powered.
    1. If no physical enable signal is wired, you may click Force enable drive from Connect tab to temporarily enable without physical signal. Note that Force enable will release (inactivate) if any of following physical inputs change state: Enable, Limit switches or Home switch.
  3. STO2 input is powered
  4. Motor typeMT is configured
  5. If Require software enableCEN is enabled, then also click Soft enable drive from Connect tab

Servo motor tuning[edit | edit source]

Tuning a servo motor is a compulsory task to make motor behave as desired and perform well during operation. Follow the Servo motor tuning guide.

Finishing touches[edit | edit source]

The last step of parameterization is to adapt settings to match the motion controller. Steps:

  1. Choose setpoint input Setpoint inputCRI to match your motion controller.
  2. If external motion controller with acceleration limit (such as CNC controller) is being used, then it is advised to set Acceleration limitCAL value to maximum of 32767 (unlimited acceleration) after motor tuning to enable motion tracking without delay. Use a limited acceleration value if drive is being used with pulse burst positioning or SimpleMotion V2 controller.
  3. If setpoint is too sensitive or not sensitive enough (such as limiting speed), then adjust setpoint scaling factory by adjusting Setpoint multiplierMUL and Setpoint dividerDIV.
  4. If setpoint signal is noisy or jittering, try enabling Setpoint smoothingCIS to smoothen it inside drive. However, leave Setpoint smoothingCIS disabled if setpoint tracking without any delay is desired.
  5. Set-up homing if required by application



Servo tuning basics[edit | edit source]

Driving a servo motor is much like driving a car. Driving a car has many similarities including the key concepts of torque, velocity and position control. Most of this happens in the driver's head the same way than a servo drive does with a motor.

For those who are already familiar with the basics, see the principles of real world servo motor drive from article Signal path of motor drive.

Driving (a.k.a servoing) a car[edit | edit source]

Driving a car to a destination is much like driving a servo motor to it's destination position. The analogies in between are:

Car Servo axis
Pedal (motor gasoline feed) Torque setpoint (motor current feed)
Speed limit Velocity setpoint
Target location Position setpoint
Speed meter Velocity feedback
Trip meter Position feedback
Car driver Servo drive

Carexample base.png

The ultimate goal of driver is to get to the target. To achieve this, he follows the road (trajectory) at certain velocity and decelerates once target is being reached. Without knowing, the driver acts as servo controller where he:

  • Controls car's velocity based on the speed meter value and speed limit
  • Controls car's position based on trip meter's reading or by observing location trough the windshield
  • All actions the driver makes, is based on comparing the setpoints and the actual state

Servo controller basics[edit | edit source]

Controller gains and a PI controller[edit | edit source]

Controller gain means sensitivity to change output due to tracking error (the difference between setpoint and feedback).

The simplest form of feedback based controller is a proportional gain controller (P controller) where output follows the formula output = Pgain*(setpoint-feedback). The problem of proportional gain controller is that it may never reach the setpoint because output starts approaching zero when the following error is reaching zero.

Because of this, it's better to add in integrating component to the controller (forming PI controller). Integrator accumulates the tracking error to a integrator variable. Integrator variable is like a bucket of water, when you add water, the water level rises and when you take out water, the level lowers. In controller the equation becomes: output = Pgain*(setpoint-feedback) + Igain*IntegralOf(setpoint-feedback).

The characteristics of feedback gain variables:

  • P-gain - reacts instantly to the tracking error but can't eliminate tracking error completely
  • I-gain - reacts slowly over time, adjusts output until tracking error is zero

When driving a car, human brain closely resembles the operation of a PI controller. For in-depth info about PI controllers and its variants, see the Wikipedia article PID controller.

Tuning the gains[edit | edit source]

Controller tuning means finding of the optimum gain values for the given system.

The proper gain values always depend on many aspects, especially the target system dynamic properties (such as motor properties, axis transmission ratios, inertias and masses). Change of properties introduces the requirement of tuning the gain values as gain values that work fine in one system may not behave satisfactory on a different system.

In servo drive case, this means that each motor type and mechanical axis need to be tuned separately. However, if axis and motors are identical, then the same gains should work equally.

Gain tuning (car) example[edit | edit source]

The following series of images illustrate an imaginary car driving scenario where the driver acts as velocity controller of the car. The magnitude of PI gain values equal the driver's aggressivity of controlling the pedal to reach the desired speed.

Low gains - sluggish response[edit | edit source]

Carexample sluggish.png

If the gains are set too low, the system response tends to be sluggish and sometimes leave a static tracking error (not reaching setpoint in any time). In this imaginary case we could think PI gains to be P=20 I=10.

Too high gains - oscillation & instability[edit | edit source]

Carexample unstablepng.png

If the gains are set too high, the system becomes overshooting, oscillating and less stable. Here the comparable PI gains could be P=200 I=100

Optimum gains - only little overshoot[edit | edit source]

Carexample stable.png

When the gains are tuned correctly, the response shows rapid response with low overshoot and no ringing or oscillations. The comparable gains here P=50 I=25.

Optimum gains with realistic setpoint - optimum response[edit | edit source]

Carexample response accellimit.png

The response can be improved further by introducing a limit to the slew rate of setpoint signal. The controller behaves optimally when the system is able to follow the setpoint continuously with little tracking error. In this case the gains could be same as before, P=50 I=25.

Real servo motor controller[edit | edit source]

See the principles of real world servo motor drive from article Signal path of motor drive.


Tuning torque controller[edit | edit source]

Torque controller tuning means finding the correct gain values for a torque controller inside the servo drive to achieve a proper response from a torque setpoint change.

Direct inductance & resistance setting method[edit | edit source]

In Granity, there is no dedicated torque control PI gains as the software supports entering motor coil inductance and resistance where the suitable PI gains are calculated from.

Method 1 (preferred)[edit | edit source]

If you are using a drive model that supports automatic measurement of inductance and resistance, follow the instructions here.

Method 2[edit | edit source]

If the above measurement function is not available, and your motor comes with coil specifications containing phase-to-phase inductance and resistance values, then the only necessary step is to enter the given values into motor Coil resistanceMR and Coil inductanceML parameter fields. In case of troubles with this method, proceed with manual tuning method.

Manual tuning method[edit | edit source]

Manual tuning of torque controller is some times done in order to optimize the torque controller response or to find the correct motor Coil resistanceMR and Coil inductanceML parameters if unknown. Manual tuning also usually yields better torque response than the direct method which may help tuning of velocity or position tuning.

In order to change torque tuning, one needs to change motor Coil resistanceMR and Coil inductanceML parameters until the torque response looks satisfactory.

Preparations[edit | edit source]

Correct torque tuning settings on the Testing tab.

Steps to do to begin torque tuning:

  • Ensure that motor is parameterized correctly and working
  • Fix the motor shaft so that it cannot rotate under full peak torque of the motor
  • Make following parameter changes to Granity and click apply afterwards:
    • Set drive in torque control mode Control modeCM
    • Set Torque bandwidth limitTBW to maximum
    • Choose Serial only setpoint input Control modeCM
    • Untick Setpoint smoothingCIS
    • Set Goals tab Setpoint dividerDIV and Setpoint multiplierMUL to 50
    • Make other necessary adjustments to have drive powered and enabled
  • Set-up the test stimulus and capture settings from Testing tab:
    • Set target setpoint 1 TSP1 to 2000-15000 (see the chapter below for finding the optimum test setpoint)
    • Set delay 1 TSD1 to 0.05 seconds
    • Set target setpoint 2 TSP2 to 0
    • Set delay1 TSD2 to 0.5 s
    • Choose sample rate Sample rateTSR of 10000 Hz or more
    • Choose Capture setpoint change ind positive direction from the dropdown
    • Tick Continuously repeating capture
    • Tick Torque setpoint and Torque achieved from signals
    • Tick Start capture to begin continous capture.
    • Tick Enable test stimulusTSE to begin a pulsed torque generation

Once the steps above are done, motor should be generating short torque pulses to a fixed shaft and torque response graphs should appear on the right side of Granity about once in 3-5 seconds.

Finding optimium test current (TSP1)[edit | edit source]

To find optimum value for TSP1, enable capture channel called "Motor output voltage" to see how much voltage is driven to motor during rising the edge of torque. For optimum TSP1 value the voltage peak should lie within 20% to 80%. If voltage gets saturated (100%), reduce TSP1 value until it stays below 80%. Images below illustrate the wrong case (first image) and correctly set case (second image).

Adjusting MR and ML to for optimum torque control[edit | edit source]

The task here is to adjust the Coil resistanceMR and Coil inductanceML parameters to achieve near optimum step response for the torque controller. Observe the images below for guidance.

TorqlowR.png

In this case the Coil resistanceMR value has been set too low causing slowly rising achieved torque curve. Such slow response would reduce servo responsiveness.

TorqhighR.png

In the opposite case (too high Coil resistanceMR value) the response shows wavy oscillations and ovesrhoot.

TorqlowL.png

Same kind of phenomenon will be seen if motor Coil inductanceML value is too low. Finding oscillation free tuning is finding the correct balance between the MR and ML as both affect each other.

TorqhigL.png

Too high Coil inductanceML will cause sharp overshooting and high frequency oscillations. Motor may produce audible noise if oscillations are continuous (occurs with way too high ML).

Torqgood.png

The above image shows near optimum torque response with fast rising edge combined to minimal overshoot.

Torqgoodspinning.png

The above image shows what may happen if motor shaft is not fixed properly (allowed to rotate). This is with the same optimum settings like the previous image.

Steps to do after manual tuning finished[edit | edit source]

  • Stop test stimulus by unticking Enable test stimulusTSE
  • Stop scope catpure by unticking Continuously repeating capture
  • Undo all temporary changes made to settings (such as Torque bandwidth limitTBW, Control modeCM, Setpoint dividerDIV, Setpoint multiplierMUL) but leave the optimized Coil resistanceMR and Coil inductanceML values active
  • Save settings to drive memory by clicking Save settings on drive non-volatile memory button

Using drive in torque mode[edit | edit source]

If torque mode is the final desired operating mode, set-up the setpoint signal source from Granity Goals tab. Also see Signal path of motor drive for explanation of torque setpoint scale.


Tuning velocity controller[edit | edit source]

Velocity controller tuning means finding the correct drive settings and feedback gain values to achieve a proper Servo stiffness and response to a velocity setpoint change.

This tuning guide is for you if the final application uses the motor in velocity control mode such as spindle or as position mode with external closed loop position controller such as LinuxCNC.

Velocity control tuning method[edit | edit source]

Preparations[edit | edit source]

An example of Testing tab settings for velocity controller tuning. Different settings should be experimented during the process to observe the stability and behavior of the settings.
Initial settings on Goals tab before beginning the example in this tuning guide.

Steps to do to begin position tuning:

  • Ensure that motor is parameterized correctly and working and torque control tuning has been properly done.
  • Attach motor to the target load and ensure it can rotate in both directions infinitely
  • Make following parameter changes to Granity and click apply afterwards:
    • Set drive in velocity control mode Control modeCM
    • Choose Serial only setpoint input Control modeCM
    • Make other necessary adjustments to have drive powered and enabled
    • Untick Setpoint smoothingCIS
    • Set Goals tab Setpoint dividerDIV and Setpoint multiplierMUL to 50
    • Set Acceleration limitCAL & Velocity limitCVL reasonably to the levels that motor is expected to handle
  • Set-up the test stimulus and capture settings from Testing tab (an example, may be varied):
    • Set target setpoint 1 TSP1 between 1000 and 16383 (16383 equals the max speed that is configured via Velocity limitCVL)
    • Set delay 1 TSD1 to 0.25 seconds
    • Set target setpoint 2 TSP2 to same, but negative, value of TSP1
    • Set delay1 STD2 to 0.25 s
    • Choose Sample rateTSR of 500 to 2500 Hz
    • Choose Capture setpoint change in positive direction from the dropdown
    • Tick Continuously repeating capture
    • Tick Velocity setpoint and Velocity achieved from signals
    • Tick Start capture to begin continous capture.
    • Tick Enable test stimulusTSE to begin a continuous position back and forth spinning motion generation

Once the steps above are done, motor should be generating direction reversing spinning and velocity response graphs should appear on the right side of Granity about once in 3-5 seconds.

Finding velocity control gain values[edit | edit source]

Tuning protocol[edit | edit source]

Tuning is begun with low or medium target speeds (TSP1 & 2 values below 5000).

Veltuning2.png

Initial velocity response with the default settings. As seen from the achieved velocity graph, it follows the setpoint velocity lazily and exhibits overshooting. In such state motor servo stiffness is low can be easily decelerated by adding load to the shaft.

Veltuning4.png

Begin tuning by increasing Velocity P gainKVP. This makes motor follow velocity setpoint much better.

To try different gains, go to Tuning tab, change value and click the Apply settings button.


Veltuning3.png

When Velocity P gainKVP has been increased too much, the system becomes unstable and may start oscillating. In such case, you may hit Esc button to disable drive, reduce the gain and enable drive again.

Tip: torque bandwidth has significant effect on the behavior of KVP value and the point where it goes unstable. One may experiment different Torque bandwidth limitTBW settings to find the optimum.

Veltuning6.png

Once a maximum perfectly stable Velocity P gainKVP value has been found, start increasing Velocity I gainKVI gain by a similar fashion. The higher KVI value is, the better servo stiffness.

Veltuning5.png

If Velocity P gainKVP is increased too much, the result is overshooting and even sustained oscillation. The cure is similar to the too high Velocity P gainKVP as described earlier.

Velocitylowgain.png

Once stable and stiff gains has been found, increase setpoint values (TSP1 & 2) to test the settings with higher speeds. If necessary adjust the gains experimentally to find the optimum tuning that works satisfactory on all needed speeds.

Advanced tuning: Feed-forwards[edit | edit source]

Feed-forward parameters may be used to boost motor responsiveness to setpoint change. Velocity feed-forward gainVFF and Acceleration feed-forward gainAFF essentially compensate system friction and mass limiting the dynamic performance.

The recommended way to tune FF gains, is to start increasing Velocity feed-forward gainVFF until the optimum level has been found. After that, increase Acceleration feed-forward gainAFF until the optimum point has been reached.

Velocitylowgainff.png

In the image above a sharp response has been achieved even with low feedback gains as feed-forward gains help motor to accelerate as demanded.

Velocitystable.png

The image above shows similar response without feed-forwards but using high feedback gain values (optimally tuned according to the previous chapter).

Problem cases[edit | edit source]

Current/torque saturation[edit | edit source]

In the following test we run motor with higher speeds (TSPn > 10000) to illustrate a typical problem case.

Currentsaturatin.png

The image above shows acceleration limited by insufficient torque produced by the motor. In this example the acceleration limit is set too high to be accelerated with the given motor torque limits (or current limits).

To verify if the problem happens due to torque limit, tick also Torque achieved and Torque setpoint signals from the Testing tab settings. In such way also motor currents will be displayed simultaneously with the position response curves. If the torque curve is limited to the set Peak current limitMMC, then the problem is insufficient torque. In the image above we can see that the torque curves are saturated/clipping at 5A and -5A levels which matches the configured Peak current limitMMC value of 5A in this demonstration.

To help this, try:

  • Increasing current limits Peak current limitMMC and Continuous current limitMCC if possible
  • Reducing Acceleration limitCAL and/or Velocity limitCVL limits

Oscillation[edit | edit source]

Velocityunstable.png

The above example shows instability and oscillation with high speeds even when the system was stable at lower speeds with the same parameters. In such case tune the system again at the most unfavorable conditions and speeds to achieve stability over all required operating conditions.

Low resolution velocity feedback[edit | edit source]

Veltuning lowres.png

The above example shows another kind of problem: low resolution of velocity graph. This happens if feedback device resolution is low, and/or test velocity setpoint is low. However tuning is still possible. Tune KVP up until you find instability (you can hear it), and then take it down for 30-50% from that. Then adjust KVI up until graph looks best (no overshooting or oscillations). You may do this procedure with several torque bandwidths (TBW param) to see which gives best result.

Steps to do after tuning finished[edit | edit source]

  • Stop test stimulus by unticking Enable test stimulusTSE
  • Stop scope capture by unticking Continuously repeating capture
  • Undo all temporary changes made to settings
  • Save settings to drive memory by clicking Save settings on drive non-volatile memory button
  • Set preferred setpoint source Setpoint inputCRI, also consider the use of Setpoint smoothingCIS
  • If setpoint signal scaling is needed, adjust Setpoint multiplierMUL and Setpoint dividerDIV values

Using drive in velocity control mode[edit | edit source]

If velocity control mode is the final desired operating mode, set-up the setpoint signal source from Granity Goals tab. Also see Signal path of motor drive for explanation of velocity setpoint scale.

Tuning position controller[edit | edit source]

Position controller tuning means finding the correct drive settings and feedback gain values to achieve a proper Servo stiffness and response to a position setpoint change.

Position control tuning method[edit | edit source]

This article describes a practical approach for finding proper drive parameters to achieve a stable and stiff position control.

Preparations[edit | edit source]

An example of Testing tab settings for position controller tuning. Different settings should be experimented during the process to observe the stability and behavior of the settings.

Steps to do to begin position tuning:

  • Ensure that motor is parameterized correctly and working and torque control tuning has been properly done.
  • Attach motor to the target machine in a position where it can rotate in both directions
  • Make following parameter changes to Granity and click apply afterwards:
    • Set drive in position control mode Control modeCM
    • Choose Serial only setpoint input Control modeCM
    • Make other necessary adjustments to have drive powered and enabled
    • Untick Setpoint smoothingCIS
    • Set Goals tab Setpoint dividerDIV and Setpoint multiplierMUL to 50
    • Set Acceleration limitCAL & Velocity limitCVL limits reasonably to the levels that motor is expected to handle
  • Set-up the test stimulus and capture settings from Testing tab (an example, may be varied):
    • Set target setpoint 1 TSP1 to 100
    • Set delay 1 TSD1 to 0.25 seconds
    • Set target setpoint 2 TSP2 to -100
    • Set delay1 TSD2 to 0.25 s
    • Choose Sample rateTSR of 500 to 2500 Hz
    • Choose Capture setpoint change in positive direction from the dropdown
    • Tick Continuously repeating capture
    • Tick Position setpoint and Position achieved from signals
    • Tick Start capture to begin continous capture.
    • Tick Enable test stimulusTSE to begin a continuous position back and forth motion generation

Once the steps above are done, motor should be generating short distance back and forth motion motion and position response graphs should appear on the right side of Granity about once in 3-5 seconds.

Finding velocity & position control gain values[edit | edit source]


The task here is to adjust the Coil resistanceMR and Coil inductanceML parameters to achieve near optimum step response for the torque controller. Observe the images below for guidance.

Posgains1.png

The image above represents the initial position step response with low feedback gains. As seen, motor reaction is sluggish, lagging and has overshooting.

Posgains2.png

The next step is to increase Velocity P gainKVP gain as much as possible. The graph may start looking acceptable but it motor still has low stiffness thus it will get lag once mechanical load increases.

To try different gains, go to Tuning tab, change value and click the Apply settings button.

Posgains3.png

When Velocity P gainKVP has been increased too much, the system becomes unstable and may start oscillating. In such case, you may hit Esc button to disable drive, reduce the gain and enable drive again.

Tip: torque bandwidth has significant effect on the behavior of KVP value and the point where it goes unstable. One may experiment different Torque bandwidth limitTBW settings to find the optimum.

Posgains4.png

Once a maximum perfectly stable Velocity P gainKVP value has been found, start increasing Velocity I gainKVI gain by a similar fashion. The higher KVI value is, the better servo stiffness.

Posgains5.png

If Velocity P gainKVP is increased too much, the result is instability and oscillation. The cure is similar to the too high Velocity P gainKVP gain as described earlier.

Posgains6.png

Once both Velocity P gainKVP and Velocity I gainKVI has been optimized, the next step is to increase Position P gainKPP gain the same way. Increasing Position P gainKPP gives better servo stiffness but may also increase overshooting. Overshoot less than 10 feedback device counts is generally considered good.

Posgains7.png

Finally after playing little bit with all of Velocity P gainKVP, Velocity I gainKVI and Position P gainKPP experimentally, we find a less overshooting response without losing much stiffness.

Curing tracking error and overshoot[edit | edit source]

If servo overshoots too much, or can't follow the trajectory precisely, several cures may be tried.

Posgains8.png

Reducing Acceleration limitCAL and/or Velocity limitCVL limits makes the trajectory easier to follow and reduces tracking error and overshooting.

Posgains9.png

The same may be also achieved by utilizing Feed-forward Velocity feed-forward gainVFF and Acceleration feed-forward gainAFF which essentially compensate system friction and mass limiting the dynamic performance.

The recommended way to tune FF gains, is to start increasing Velocity feed-forward gainVFF until the optimum level has been found. After that, increase Acceleration feed-forward gainAFF until the optimum point has been reached.

Poscurrentsaturation.png

If following the tuning procedure does not result in satisfactory tracking performance, the problem may be asking too much from the motor. In the example above the acceleration limit is set too high to be accelerated with the given motor torque limits (or current limits).

To verify if the problem happens due to torque limit, tick also Torque achieved and Torque setpoint signals from the Testing tab settings. In such way also motor currents will be displayed simultaneously with the position response curves. If the torque curve is limited to the set, Peak current limitMMC, then the problem is insufficient torque. In the image above we can see that the torque curves are saturated at 4A and -4A levels which matches the configured Peak current limitMMC value of 4A in this demonstration.

To help this, try:

  • Increasing Peak current limitMMC and Continuous current limitMCC if possible
  • Reducing Acceleration limitCAL and/or Velocity limitCVL limits

Steps to do after tuning finished[edit | edit source]

  • Stop test stimulus by unticking Enable test stimulusTSE
  • Stop scope capture by unticking Continuously repeating capture
  • Undo all temporary changes made to settings
  • Save settings to drive memory by clicking Save settings on drive non-volatile memory button
  • Set preferred setpoint source Setpoint inputCRI, also consider the use of Setpoint smoothingCIS
  • If setpoint signal scaling is needed, adjust Setpoint multiplierMUL and Setpoint dividerDIV values. See Signal path of motor drive for explanation of velocity setpoint scale.

Warning: Display title "IONI user guidebook" overrides earlier display title "IONI parameterization".


In no event the Product Information or parts hereof shall be regarded as guarantee of conditions or characteristics. The Product Information or any part thereof may also not be regarded as a warranty of any kind. No liability of any kind shall be assumed by Author with respect to Product Information or any use made by you thereof, nor shall Author indemnify you against or be liable for any third party claims with respect to such information or any use thereof.

As content of this Wiki may be edited by user community, Granite Devices Oy or it's affiliates do not take any responsibility of the contents of this Wiki. Use information at your own risk. However, Granite Devices staff attempts to review all changes made to this Wiki and keep information trustworthy.

Without written consent, Granite Devices' Products or Intellectual Property shall not be used in situations or installations where living beings, material property, or immaterial property could be harmed by the operation, features or failures of Product. Products may only be used in a way where hazards like moving parts, electric shock, laser radiation, or fire can't be realized even if the content of this Wiki would suggest otherwise.