Motor compatibility guide

From Granite Devices Knowledge Wiki
Revision as of 17:51, 9 February 2018 by Tero K (Talk | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

Jump to: navigation, search

This page guides through matching the Granite Devices drive and various kinds of servo and stepping motors. See also Drive feature matrix.

Overview[edit | edit source]

Drive selection by motor.png

Refer to notes A-D below the image

Note A (position feedback device)[edit | edit source]

Servo motor requires a position feedback device to operate with servo drive. It is recommended to have a position sensor that has resolution of at least 1000 increments (a.k.a. counts) per revolution. The higher the resolution, the better servo stiffness can be achieved.

Feedback device type must be one of the supported types. Following types are supported by different drive models:

ARGON
IONI

About Hall sensors[edit | edit source]

Many AC/BLDC motors come also with Hall sensors. Hall sensors are supported by ARGON & IONI drives but these are not required for operation and can be left unconnected. Connecting & enabling Hall sensor can be used to speed up motor initialization at power-on. For more info, see Phasing a.k.a. phase search.

Unsupported feedback devices[edit | edit source]

Feedback devices that are not listed as supported, can be assumed to be unsupported and unsuitable. Examples of such types are:

  • Tachogenerator/tachometer

In case of unsupported type, motor can be usually made compatibly by installing a compatible encoder in it. Compatible encoders are widely available in may sizes and fit most motors in the market. See list of compatible feedback devices.

Note B (current rating)[edit | edit source]

Current is the component to produce torque on motor. Motor torque is directly proportional to torque generated with equation T=I*K where T is torque, I is current and K is the torque constant of motor (motor specific value, often defined in data sheet).

If drive is unable to drive (or is set deliberately to limit current) below motor ratings, it will cause the obtainable peak torque to be reduced. The reduction is proportional to the current reduction. For example, if motor is rated for 30A and drive can supply 20A, then torque is reduced by ratio 20/30 thus maximum obtainable torque is 67% of motor maximum rating.

Motorcurves rated.png

Example of motor torque vs speed curves at their specified currents and voltages

Motorcurves currentlimited.png

Example of motor torque vs speed curves with drive that limits the torque output below motor spec

Note C (voltage rating)[edit | edit source]

Voltage rating of motor originates from the characteristics of motor winding (voltage loss of motor + generated voltage of motor). Motor voltage rating is specified so that motor is able to operate at it's rated speed range and produce maximum torque whenever necessary.

If drive's supply voltage is less than motor's rated voltage, it eventually starts to reduce maximum obtainable speed of motor. This limit first appears at maximum torque, but if supply voltage is significantly less than motor voltage rating, motor will not be able to run at it's rated speed. Voltage and speed are directly proportional. For example if motor voltage rating is 100V, and drive supply voltage is 50V, then top speed may be reduced as much as 50%. In practical cases, speed loss is less because motors usually have headroom for voltage variations so in reality 100V to 50V drop might cause motor to lose only 20-40% of rated speed.

Motorcurves rated.png

Example of motor torque vs speed curves at their specified currents and voltages

Motorcurves voltagelimited.png

Example of motor torque vs speed curves with drive that has lower supply voltage than motor specification

Note A and B combined (current & voltage rating)[edit | edit source]

If motor has higher voltage AND current rating of drive, it will mean reduction of maximum speed and torque.

Motorcurves voltagecurrentlimited.png

Example of motor torque vs speed curves with drive that has lower supply voltage AND lower output current than motor specification

Note D (stepping motor feedback)[edit | edit source]

Stepping are used traditionally without any feedback devices (in open loop mode) or with feedback device (position sensor) to run in closed loop mode. For explanation of different possible modes, see Using stepping motor with IONI.

See also[edit | edit source]


In no event the Product Information or parts hereof shall be regarded as guarantee of conditions or characteristics. The Product Information or any part thereof may also not be regarded as a warranty of any kind. No liability of any kind shall be assumed by Author with respect to Product Information or any use made by you thereof, nor shall Author indemnify you against or be liable for any third party claims with respect to such information or any use thereof.

As content of this Wiki may be edited by user community, Granite Devices Oy or it's affiliates do not take any responsibility of the contents of this Wiki. Use information at your own risk. However, Granite Devices staff attempts to review all changes made to this Wiki and keep information trustworthy.

Without written consent, Granite Devices' Products or Intellectual Property shall not be used in situations or installations where living beings, material property, or immaterial property could be harmed by the operation, features or failures of Product. Products may only be used in a way where hazards like moving parts, electric shock, laser radiation, or fire can't be realized even if the content of this Wiki would suggest otherwise.