Editing Argon user guide/Wiring

<span style="color:red">'''This article state is work in progress & unchecked! Use at your own risk.'''</span>
==Front connectors==
[[File:Argonfront.png|800px|Argon front side connections]]
===J1 feedback device port===
[[File:J1closeup.png|thumb|J1 connector. Click to enlarge and see pin numbering.]]
J1 connector type is 15 pin female D-Sub and should be mated with 15 pin male D-Sub counterpart.

J1 pinout is to be announced later.

===J2.1 and J2.2 Simplemotion & E-stop ports===
J2.1 and J2.2 are RJ45 type connectors and mates with standard Cat 5 & 6 ethernet cables. Both of these ports are connected pin-to-pin parallel to allow chaining of Argon devices. For J2.x pinout, see [[SimpleMotion V2 port]] article.

===J3 24V power and motor brake port===
J3 is a 3 pole terminal block type connector used for supplying 24VDC to drive and optionally controlling motor solenoid brake.

{| class="wikitable"
|-
! Pin #||Pin name !! Description !! Connection
|-
| 1||BK || Motor brake output || If motor has a 24V solenoid brake, connect brake between BK and V+
|-
| 2||V+ || 24V supply positive input || Connect to 24V PSU +
|-
|3|| V- || 24V supply ground, on J1, J2.x and J5 connectors tied to GND || Connect to 24V PSU -
|}
24VDC typical current consumption is between 0.1 - 0.7ADC depending on how much current is drawn by feedback device and an optional motor brake.

Normally an ethernet type cable is plugged from J2.1 or J2.2 to [[SimpleMotion V2 USB adapter]]

===J4 power & motor port===
J4 is a 10 pole terminal block connector for several functions: earthing, AC power input, motor output, regenerative resistor output and HV DC link sharing.

{{electricshock|Dangerous & non-isolated mains potential voltages are present in this connector! Keep away from this connector and its wiring when drive has been powered recently. Carefully read [[Power supply safe discharging]] before operating.}}

{| class="wikitable"
|-
! Pin #||Pin name !! Descrpition !! AC/BLDC motor connection || Brush DC motor connection
|-
| 1||VN || HV DC link negative rail || colspan=2| Do not connect
|-
| 2||BR || Braking resistor output || colspan=2|Optional braking resistor first terminal. See [[Argon braking resistor]]
|-
| 3||VP || HV DC link positive rail || colspan=2|Optional braking resistor first terminal. See [[Argon braking resistor]]
|-
| 4||PE &#9178; || Protective earth || colspan=2|Connect to motor PE conductor and motor cable shield
|-
| 5||U || Motor phase output || Motor U phase ¹ || Motor armature+
|-
| 6||V || Motor phase output || Motor V phase ¹ || Motor armature-
|-
| 7||W || Motor phase output || Motor W phase ¹ || No connection 
|-
| 8||L || AC mains supply Line || colspan=2|Connect to AC supply line
|-
| 9||N || AC mains supply Neutral || colspan=2|Connect to AC supply neutral
|-
| 10||PE &#9178; || Protective earth || colspan=2|Connect to supply protective earth. <span style="color:red">'''This connection is always mandatory when any voltage larger than 30 VAC or 42 VDC is supplied to the device!'''</span>
|}
¹ In some motors U,V,W phases are called R,S,T instead.

==Side connectors==
[[File:ArgonSideIO.png|600px|Argon side connections & DIP switches]]
===J5 Inputs/Outputs===
J5 Is a 26 pin [http://en.wikipedia.org/wiki/Insulation-displacement_connector IDC connector] located on the side of Argon. The connector serves as general purpose I/O including:
*Isolated digital inputs (4 pcs) - used for limit & home switches and clear faults signal
*Isolated digital outputs (4 pcs) - used for status indication
*Differential analog inputs (2 pcs) - used as [[Reference signal|Analog reference]]
*Differential digital inputs (2 pcs) - used for pulse/direction or second encoder
*5V and GND output - used for supplying switches or external electronics
====Pin-out====
Please see [[Argon I/O connector electrical interfacing]] before wiring to this port.
{| class="wikitable"
|-
! Pin # !! Pin name !! Electrical || Isolated || Function¹
|-
| 1 || GND || [[Argon I/O connector electrical interfacing#Supply| Supply ]]|| rowspan=10|No² ||  Ground
|-
| 2 || +5V_OUT ||  [[Argon I/O connector electrical interfacing#Supply| Supply ]] || 5V output
|-

| 3 || HSIN1- ||  [[Argon I/O connector electrical interfacing#High speed input| High speed digital input ]] || rowspan=2 |Pulse train, Quadrature or PWM [[Reference signal|input reference]]
|-
| 4 || HSIN1+ ||  [[Argon I/O connector electrical interfacing#High speed input| High speed digital input ]] 
|-

| 5 || HSIN2- ||  [[Argon I/O connector electrical interfacing#High speed input| High speed digital input ]] || rowspan=2 |Future use (i.e. secondary feedback device)
|-
| 6 || HSIN2+ ||  [[Argon I/O connector electrical interfacing#High speed input| High speed digital input ]] 
|-

| 7 || ANAIN1- || [[Argon I/O connector electrical interfacing#Analog input| Analog input ]] || rowspan=2 |Analog [[Reference signal|input reference]]
|-
| 8 || ANAIN1+ || [[Argon I/O connector electrical interfacing#Analog input| Analog input ]] 
|-

| 9 || ANAIN2- || [[Argon I/O connector electrical interfacing#Analog input| Analog input ]] || rowspan=2 |Future use (i.e. secondary feedback device)
|-
| 10 || ANAIN2+ ||  [[Argon I/O connector electrical interfacing#Analog input| Analog input ]] 
|-

| 11 || GPO1- ||  [[Argon I/O connector electrical interfacing#Digital output| Digital output ]] || rowspan=16 |Yes² || rowspan=2 | Servo ready status. True when drive is initialized and ready to accept user commands/reference.
|-
| 12 || GPO1+ || [[Argon I/O connector electrical interfacing#Digital output| Digital output]] 
|-

| 13 || GPO2- || [[Argon I/O connector electrical interfacing#Digital output| Digital output ]] || rowspan=2 | Follow error warning status. True when following error has reached more than user configured 1/8 of fault limit value.
|-
| 14 || GPO2+ || [[Argon I/O connector electrical interfacing#Digital output| Digital output]] 
|-

| 15 || GPO3- || [[Argon I/O connector electrical interfacing#Digital output| Digital output ]] || rowspan=2 | Fault stop status. True when drive is stopped due to fault.
|-
| 16 || GPO3+ || [[Argon I/O connector electrical interfacing#Digital output| Digital output]] 
|-

| 17 || GPO4- || [[Argon I/O connector electrical interfacing#Digital output| Digital output ]] || rowspan=2 | Braking status. Set true when drive attempts to brake motor.
|-
| 18 || GPO4+ || [[Argon I/O connector electrical interfacing#Digital output| Digital output]] 
|-

| 19 || GPI1- || [[Argon I/O connector electrical interfacing#Digital output| Digital input ]] || rowspan=2 | Home switch input.
|-
| 20 || GPI1+ || [[Argon I/O connector electrical interfacing#Digital output| Digital input]] 
|-

| 21 || GPI2- || [[Argon I/O connector electrical interfacing#Digital output| Digital input ]] || rowspan=2 | Positive feed enable input. Used for axis limit switches.
|-
| 22 || GPI2+ || [[Argon I/O connector electrical interfacing#Digital output| Digital input]] 
|-

| 23 || GPI3- || [[Argon I/O connector electrical interfacing#Digital output| Digital input ]] || rowspan=2 | Negative feed enable input. Used for axis limit switches.
|-
| 24 || GPI3+ || [[Argon I/O connector electrical interfacing#Digital output| Digital input]] 
|-

| 25 || GPI4- || [[Argon I/O connector electrical interfacing#Digital output| Digital input ]] || rowspan=2 | Clear drive faults input. Transition from false to true attempts to reset active faults of drive. If drive is simultaneously in enabled state, motor will start moving immediately.
|-
| 26 || GPI4+ || [[Argon I/O connector electrical interfacing#Digital output| Digital input]] 
|-
|}
¹) This is the default function with stock firmware. Function may be different in future or custom firmware versions.

²) Non-isolated lines are referenced to GND pin / J3 V- terminal. Isolated lines have functional isolation between GND and other isolated +-/- pairs.

===J6 Expansion slot===
This slot is reserved for [[Argon add-on card]] that may be installed inside the drive.

===DIP Switches===
DIP switches serves as [[Setting device bus address|address selector]] when connecting the drive to [[SimpleMotion V2]] bus or [[Granity]].

==Mating parts==
See list of [[Argon mating connectors and accessories]]