Editing Argon user guide/Wiring

{{ArgonManualNav}}<span style="color:red">'''This article state is work in progress & unchecked! Use at your own risk.'''</span>
==Wiring overview==
[[File:Wiringoverview notitle.png|800px]]

;The minimum wiring for a servo system (after configuration state):
# Safety [[Argon user guide/Earthing|earthing ]]to port J4 and preferably to the [[Argon user guide/Earthing|Argon case]]
# 24 VDC wiring to port J3
# [[Safe torque off]] and enable signals to port J2. See [[SimpleMotion V2 port|how]].
# Motion [[controller]] wiring:
## if pulse & direction, analog, PWM or quadrature setpoint signal used, wire signals to port J5
## if setpoint delivered over SimpleMotion V2 bus, then a cable from [[SimpleMotion V2 compatible communication interface device]] to J2
# Axis limit [[Argon user guide/J5 connector electrical interfacing|switches wired to port J5]]
# [[Feedback devices|Feedback device]] wiring to port J1
# Motor connection to port J4
# AC input power to port J4. Use an external fuse with this input.
;Optional wiring
# AC [[Power line filter]] on the wire entering J4
# Wiring of optional [[Argon user guide/Braking resistor|braking resistor]] to port J4
# Motor solenoid brake wiring to port J3
;Additionally following are required for drive configuration with [[Granity]]:
# A cable from [[SimpleMotion V2 USB adapter]] to port J2

==Ports and connectors==
[[File:Argonfront.png|800px|Argon front side connections]]
[[File:ArgonSideIO.png|550px|Argon side connections & DIP switches]]

===J1 feedback device port===
J1 connector type is 15 pin female D-Sub and should be mated with 15 pin male D-Sub counterpart. 

For pin-out and connection examples, see the main article [[Argon user guide/J1 connector wiring|J1 connector wiring]].

===J2.1 and J2.2 Simplemotion & E-stop ports===
J2.1 and J2.2 are RJ45 type connectors and mates with standard Cat 5 & 6 Ethernet cables. Both of these ports are connected pin-to-pin parallel to allow chaining of Argon devices. 

See the main article [[SimpleMotion V2 port]].

===J3 24V power and motor brake port===
J3 is a 3 pole terminal block type connector used for supplying 24VDC to drive and optionally controlling motor solenoid brake. 

See the main article [[Argon user guide/J3 connector wiring|J3 connector wiring]].

===J4 power & motor port===
J4 is a 10 pole terminal block connector for several functions: earthing, AC power input, motor output, regenerative resistor output and HV DC link sharing. 

See the main article [[Argon user guide/J4 connector wiring|J4 connector wiring]].

===J5 Inputs/Outputs===
J5 Is a 26 pin [http://en.wikipedia.org/wiki/Insulation-displacement_connector IDC connector] located on the side of Argon. The connector serves as general purpose I/O with [[setpoint signal]] inputs featuring: limit & home switch inputs, status indicator outputs, [[[[Analog setpoint|analog]], [[Pulse and direction|pulse and direction]], [[quadrature]] or [[PWM]] types of [[Setpoint signal|setpoint]] inputs and secondary [[feedback devices|feedback device]] input.

See the main article [[Argon I/O connector electrical interfacing]] for pin-out and wiring guide.

===J6 Expansion slot===
This slot is reserved for [[Argon add-on card]] that may be installed inside the drive.

===DIP Switches===
DIP switches serves as address selector when connecting the drive to [[SimpleMotion V2]] bus or [[Granity]].

See the main article [[Setting device bus address]].

==Mating parts==
See list of [[Argon mating connectors and accessories]]
==Wiring recommendations==
Read general wiring recommendations articles at:
*[http://www.electrical-installation.org/enwiki/Wiring_recommendations Wire routing recomendations]
*[http://www.electrical-installation.org/enwiki/EMC_implementation_-_Implementation_of_shielded_cables Cable shield connection]

==Basic wiring scheme==
Basic wiring scheme of Argon (servo drive). Use of shielded cables is optional but highly recommended for EMI compliance and optimal reliability. 

[[File:Argonwiringoverview.png|800px]]