Editing ATOMI connectors and pinouts

===Legend===
{| class="wikitable"
|-
! Color
|-
| class="powpin" |Supply pin
|-
| class="inpin" |Input pin
|-
| class="outpin" |Output pin
|}


===MX, MY, MZ, MA - Motor and encoder connectors===

{| class="wikitable"
|-
!  Pin number !! Signal name !! Usage
|-
| 1 || class="inpin" | SW || Limit switch, shared for both directions
|-
| 2 || class="inpin" | CHC / Homeswitch || Encoder index channel / homeswitch
|-
| 3 || class="inpin" | CHB || Encoder channel B
|-
| 4 || class="inpin" | CHA || Encoder channel A
|-
| 5|| class="powpin" |+5 V || 5 V supply voltage to encoder
|-
| 6|| class="powpin" |GND || Encoder supply ground / 0 V
|-
| 7|| class="outpin" |PH4 || Motor phase 4
|-
| 8|| class="outpin" |w / PH3 || Motor phase 3 / Servo W
|-
| 9|| class="outpin" |V / PH2 || Motor phase 2 / Servo V
|-
| 10|| class="outpin" |U / PH1 || Motor phase 1 / Servo U
|}

===X2 pinout===
X2 is main control and [[setpoint]] signal port consisting Global Enable input signal, Global Fault output signal, [[pulse and direction]]/[[PWM]] setpoint inputs and digital outputs for servo ready signals. X2 is directly wired to conform most common parallel port style pulse & direction CNC controllers.
{| class="wikitable"
! Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
| class="tableseparator" rowspan="14" |
!Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
|-
| 1||1|| class="inpin" |ENABLE |||Enable all axis (with or without chargepump)||2||14|| class="inpin" |Homing|| Start homing for all axis
|-
| 3||2|| class="inpin" |HSIN2_X||Direction input X||4||15|| class="outpin" |Global_GPO3||Global fault output
|-
| 5||3|| class="inpin" |HSIN1_X||Pulse/step input X||6||16|| class="inpin" |PWM2ANA||PWM to analogue converter input
|-
| 7||4|| class="inpin" |HSIN2_Y||Direction input Y||8||17|| class="inpin" |AUX_IN||Auxilary transistor input
|-
| 9||5|| class="inpin" |HSIN1_Y||Pulse/step input Y||10||18|| class="powpin" |GND|| rowspan="8" |Ground
|-
| 11||6|| class="inpin" |HSIN2_Z||Direction input Z||12||19|| class="powpin" |GND
|-
| 13||7|| class="inpin" |HSIN1_Z||Pulse/step input Z||14||20|| class="powpin" |GND
|-
| 15||8|| class="inpin" |HSIN2_A||Direction input A||16||21|| class="powpin" |GND
|-
| 17||9|| class="inpin" |HSIN1_A||Pulse/step input A||18||22|| class="powpin" |GND
|-
| 19||10|| class="outpin" |GPO1_X|| X axis servo ready signal ||20||23|| class="powpin" |GND
|-
| 21||11|| class="outpin" |GPO1_Y||Y axis servo ready signal||22||24|| class="powpin" |GND
|-
| 23||12|| class="outpin" |GPO1_Z||Z  axis servo ready signal||24||25|| class="powpin" |GND
|-
| 25||13|| class="outpin" |GPO1_A||A  axis servo ready signal||26||N/A||Not connected||
|}

{{damage|Connect X4/X5 only to 3.3V or 5V logic systems. For 24V logic the use of [[IONICUBE 1X]] is recommended}}

===X3 pinout===
X3 is a second control and [[setpoint]] signal port addition to X2. X3 consists analog setpoint signal inputs and additional digital I/O. 
{| class="wikitable"
! Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
| class="tableseparator" rowspan="14" |
!Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
|-
| 1||1|| class="powpin" |GND |||GND / 0 V||2||14|| class="powpin" |+5V|| +5 V supply
|-
| 3||2|| class="powpin" |GND||GND / 0 V||4||15|| class="outpin" |Global_IO4||Global IO 4
|-
| 5||3|| class="outpin" |AUX_OUT||Buffered output for AUX_IN||6||16|| class="outpin" |ANA_OUT||PWM to analogue converter output, 0..5 V
|-
| 7||4|| class="inpin" |X_GPI2||Enable positive X travel||8||17|| class="inpin" |X_GPI3||Enable negative X travel
|-
| 9||5|| class="outpin" |X_GPO4||X position within limits||10||18|| class="outpin" | X_GPO2 || X tracking error
|-
| 11||6|| class="inpin" |X_ANAIN|| X analogue setpoint input||12||19|| class="inpin" |Y_GPI2 || Enable positive Y travel
|-
| 13||7|| class="inpin" |Y_GPI3||Enable negative Y travel||14||20|| class="outpin" | Y_GPO4 ||Y position within limits
|-
| 15||8|| class="outpin" |Y_GPO2||Y tracking error||16||21|| class="inpin" |Y_ANAIN || Y analogue setpoint input
|-
| 17||9|| class="inpin" |Z_GPI2||Enable positive Z travel||18||22|| class="inpin" |Z_GPI3 || Enable positive Z travel
|-
| 19||10|| class="outpin" |Z_GPO4|| Z position within limits ||20||23|| class="outpin" |Z_GPO2 || Z tracking error
|-
| 21||11|| class="inpin" |Z_ANAIN||Z analogue setpoint input||22||24|| class="inpin" |A_GPI2 || Enable positive A travel
|-
| 23||12|| class="inpin" |A_GPI3||Enable negative A travel||24||25|| class="outpin" |A_GPO4 || A position within limits
|-
| 25||13|| class="outpin" |A_GPO2||A tracking error||26||N/A|| class="inpin" | A_ANAIN ||A analogue setpoint input
|}