Difference between revisions of "Argon user guide/LED indicators"
From Granite Devices Knowledge Wiki
| [checked revision] | [checked revision] |
| Line 1: | Line 1: | ||
| + | Argon has four front panel led indicators which have dedicated indicating tasks: | ||
| + | *LD1 SimpleMotion transmit led. Blinks when drive transmits data to bus. | ||
| + | *LD2 SimpleMotion receive led. Blinks when drive receives data from bus. | ||
| + | *LD3 Fault indicator | ||
| + | *LD4 Motor control state indicator | ||
| + | ==How to read indications== | ||
| + | *LD1 and LD2, blink very briefly during data transmission. Due to short light pulses, these lights appear dimmer than other leds. | ||
| + | *LD3 and LD4 have programmed blinking sequences. Sequences consists series of short (S) and long (L) light pulses. For example LLS means the led will blink two long flashs and then one short flash. After sequence there will be a pause before the sequence repeats. | ||
| + | |||
| + | ==List of all LD3 and LD4 sequences== | ||
| + | To see animations, make sure web browser animations are enabled. | ||
| + | |||
===High priority faults=== | ===High priority faults=== | ||
{| class="wikitable" | {| class="wikitable" | ||
Revision as of 21:49, 29 May 2013
Argon has four front panel led indicators which have dedicated indicating tasks:
- LD1 SimpleMotion transmit led. Blinks when drive transmits data to bus.
- LD2 SimpleMotion receive led. Blinks when drive receives data from bus.
- LD3 Fault indicator
- LD4 Motor control state indicator
Contents
How to read indications
- LD1 and LD2, blink very briefly during data transmission. Due to short light pulses, these lights appear dimmer than other leds.
- LD3 and LD4 have programmed blinking sequences. Sequences consists series of short (S) and long (L) light pulses. For example LLS means the led will blink two long flashs and then one short flash. After sequence there will be a pause before the sequence repeats.
List of all LD3 and LD4 sequences
To see animations, make sure web browser animations are enabled.
High priority faults
| Fault reason !! LED sequence | LED sequence as text | |
| Hardware |  |
SLLS |
| Program or memory |  |
SLSL |
| Internal comm error (unable to establish comm) |  |
SLSS |
| Internal comm error (in middle of operation) |  |
SSLL |
| SimpleMotion communication |  |
LSSS |
| Other/unknown |  |
LLSL |
Faults causing fault stop state
| Fault reason | LED sequence | LED sequence as text |
|---|---|---|
| Hardware |  |
LLSS |
| Progral or memory |  |
LSLL |
| Internal comm error (CRC) |  |
LSL |
| Initialization |  |
LSS |
| Over current |  |
SLL |
| Over temperature |  |
LSLS |
| Over voltage |  |
SLS |
| Following error |  |
LS |
| Under voltage |  |
SL |
| Motion blocked or motor runaway | |
SSL |
| Reference range exceeded |  |
LSSL |
| Other/unknown |  |
SSSL |
Motor control states
| Status | LED sequence | LED sequence as text | Motor output powered |
|---|---|---|---|
| Permanent stop (need device reset) |  |
LLS | No |
| Fault stop (observe LD3 for reason) |  |
Off | Depends on fault |
| Follow error recovery motion |  |
LS | Yes |
| Initializing |  |
SL | Yes |
| Homing |  |
LSS | Yes |
| Run |  |
On | yes |
