Difference between revisions of "Granity user guide/Goals"
From Granite Devices Knowledge Wiki
| [checked revision] | [checked revision] |
(→Parameters) |
(→Parameters) |
||
| Line 6: | Line 6: | ||
* Setup [[Axis homing||axis homing]] | * Setup [[Axis homing||axis homing]] | ||
==Parameters== | ==Parameters== | ||
| + | Selecting drive function | ||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
| Line 11: | Line 12: | ||
|- | |- | ||
| CM || Control mode || Select drive operating [[Control modes|control mode]] || Select Torque, Velocity or Position mode. | | CM || Control mode || Select drive operating [[Control modes|control mode]] || Select Torque, Velocity or Position mode. | ||
| + | |} | ||
| + | |||
| + | Setpoing input signal | ||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | ! Short [[GUI]] name !! [[GUI]] name !! Description !! How to use | ||
|- | |- | ||
| CRI || Setpoint input || Source the of [[setpoint signal]] || Choose one from Serial only [[SimpleMotion V2|SMV2]], [[Pulse and direction]], [[Quadrature]], [[PWM]] or [[Analog setpoint]] | | CRI || Setpoint input || Source the of [[setpoint signal]] || Choose one from Serial only [[SimpleMotion V2|SMV2]], [[Pulse and direction]], [[Quadrature]], [[PWM]] or [[Analog setpoint]] | ||
| Line 18: | Line 25: | ||
| CAS||Setpoint scaling factor||Variable to adjust the scale of setpoint signal||Value of 100% will pass the setpoint unchanged through the setpoint scaler. For example setting 200% here will equal doubling the amplitude of setpoint signal (i.e. in pulse train mode, one pulse equals two pulses, or in analog mode 5V equals 10V). | | CAS||Setpoint scaling factor||Variable to adjust the scale of setpoint signal||Value of 100% will pass the setpoint unchanged through the setpoint scaler. For example setting 200% here will equal doubling the amplitude of setpoint signal (i.e. in pulse train mode, one pulse equals two pulses, or in analog mode 5V equals 10V). | ||
|} | |} | ||
| − | + | Velocity & acceleration limits | |
| + | {| class="wikitable" | ||
| + | |- | ||
| + | ! Short [[GUI]] name !! [[GUI]] name !! Description !! How to use | ||
| + | |- | ||
| + | |CAL||Acceleration limit|| || | ||
| + | |- | ||
| + | |CVL||Velocity limit || || | ||
| + | |- | ||
| + | |CSD||Stop deceleration|| NO EFFECT CURRENTLY|| | ||
| + | |- | ||
| + | |CRV||Error recovery velocity || || | ||
| + | |} | ||
| + | Homing | ||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | ! Short [[GUI]] name !! [[GUI]] name !! Description !! How to use | ||
| + | |- | ||
| + | |HME||Homing enabled|| || | ||
| + | |- | ||
| + | |HMS||Home switch polarity|| || | ||
| + | |HMI||Index pulse search|| || | ||
| + | |HMH|| Hard stop detection threshold|| || | ||
| + | |HMT||Motor current limit during homing|| || | ||
| + | |HMV||Homing velicty limit|| || | ||
| + | |HMA|| Homing acceleration limit|| || | ||
| + | |HMF||Offset home after homing|| || | ||
| + | |HFO||Full speed offset move|| || | ||
| + | |HLL||Position soft low limit|| || | ||
| + | |HHL|| | ||
| + | |} | ||
[[Category:Granity user guide]] | [[Category:Granity user guide]] | ||
Revision as of 13:51, 14 August 2013
Granity Goals tab
The Goals tab in the GDtool 3 serves following purpses:
- Choose drive control mode
- Choose setpoint signal and its scale
- Set motion acceleration & velocity limits
- Setup |axis homing
Parameters
Selecting drive function
| Short GUI name | GUI name | Description | How to use |
|---|---|---|---|
| CM | Control mode | Select drive operating control mode | Select Torque, Velocity or Position mode. |
Setpoing input signal
| Short GUI name | GUI name | Description | How to use |
|---|---|---|---|
| CRI | Setpoint input | Source the of setpoint signal | Choose one from Serial only SMV2, Pulse and direction, Quadrature, PWM or Analog setpoint |
| CIS | Setpoint smoothing | Low pass filtering of setpoint signal | Tick the checkbox to smoothen the setpoint signal. This is useful if setpoint is noisy or jittering. However, if fastest response to the input is desired, leave this unticked. Also if using CAS>100%, this may help to smoothen the motion. |
| CAS | Setpoint scaling factor | Variable to adjust the scale of setpoint signal | Value of 100% will pass the setpoint unchanged through the setpoint scaler. For example setting 200% here will equal doubling the amplitude of setpoint signal (i.e. in pulse train mode, one pulse equals two pulses, or in analog mode 5V equals 10V). |
Velocity & acceleration limits
| Short GUI name | GUI name | Description | How to use |
|---|---|---|---|
| CAL | Acceleration limit | ||
| CVL | Velocity limit | ||
| CSD | Stop deceleration | NO EFFECT CURRENTLY | |
| CRV | Error recovery velocity |
Homing
| Short GUI name | GUI name | Description | How to use | ||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| HME | Homing enabled | ||||||||||||||||||||||||||||||||||||
| HMS | Home switch polarity | HMI | Index pulse search | HMH | Hard stop detection threshold | HMT | Motor current limit during homing | HMV | Homing velicty limit | HMA | Homing acceleration limit | HMF | Offset home after homing | HFO | Full speed offset move | HLL | Position soft low limit | HHL |
