Difference between revisions of "Argon resolver adapter"
| [checked revision] | [checked revision] |
| Line 2: | Line 2: | ||
Argon resolver adapter is a small sized adapter device that adds [[Feedback devices|resolver]] feedback device support to [[Argon]] servo drive. | Argon resolver adapter is a small sized adapter device that adds [[Feedback devices|resolver]] feedback device support to [[Argon]] servo drive. | ||
==Usage== | ==Usage== | ||
| + | ===Wiring=== | ||
[[File:Resolveradapterwiring.png|thumb|320px|Connection of resolver to adapter.]] | [[File:Resolveradapterwiring.png|thumb|320px|Connection of resolver to adapter.]] | ||
| − | Resolver has total of 6 wires and 3 windings: one for rotor (primary) and two stators (secondaries). Rotor connects to the adapter pins A+ and A- while secondaries connect to B+/- and C+/- | + | Resolver has total of 6 wires and 3 windings: one for rotor (primary) and two stators (secondaries). Rotor connects to the adapter pins A+ and A- while secondaries connect to B+/- and C+/-. |
If pin-out of resolver is unknown, it can be found out with multimeter by finding the wire pairs where coils are connected. Rotor can be identified by searching for lowest resistance coil. Stators typically have at least twice as high resistance compared to rotor. | If pin-out of resolver is unknown, it can be found out with multimeter by finding the wire pairs where coils are connected. Rotor can be identified by searching for lowest resistance coil. Stators typically have at least twice as high resistance compared to rotor. | ||
| + | |||
| + | A shielded cable is required and shield should be connected to D-sub connector frame to reduce [[EMI]] noise. Shielded cable for motor power leads and connection of cable shield and motor frame to drive PE is strongly recommended if not necessary to reduce noise. After all noise countermeasures, some noise is still expected from resolver read-out due to analog nature of the signals. This noise will appear as position value noise and motor hiss when standing still or rotating slowly. | ||
| + | ===Configuration=== | ||
| + | To configure drive for resolver: | ||
| + | *Choose Resolver from feedback device parameter [[FBD]] | ||
| + | *Set feedback device resolution [[FBR]] to 2048 PPR (resolver will give same resolution as 2048 PPR / 8192 count encoder) | ||
| + | *Tune motor normally. If motor is always unstable or locks motor position, try changing direction of feedback by toggling checkbox [[FBI]] | ||
| + | |||
[[category:Motor drives]] | [[category:Motor drives]] | ||
[[category:Argon]] | [[category:Argon]] | ||
Revision as of 16:36, 28 March 2014
Argon resolver adapter is a small sized adapter device that adds resolver feedback device support to Argon servo drive.
Usage
Wiring
Resolver has total of 6 wires and 3 windings: one for rotor (primary) and two stators (secondaries). Rotor connects to the adapter pins A+ and A- while secondaries connect to B+/- and C+/-.
If pin-out of resolver is unknown, it can be found out with multimeter by finding the wire pairs where coils are connected. Rotor can be identified by searching for lowest resistance coil. Stators typically have at least twice as high resistance compared to rotor.
A shielded cable is required and shield should be connected to D-sub connector frame to reduce EMI noise. Shielded cable for motor power leads and connection of cable shield and motor frame to drive PE is strongly recommended if not necessary to reduce noise. After all noise countermeasures, some noise is still expected from resolver read-out due to analog nature of the signals. This noise will appear as position value noise and motor hiss when standing still or rotating slowly.
Configuration
To configure drive for resolver:
- Choose Resolver from feedback device parameter FBD
- Set feedback device resolution FBR to 2048 PPR (resolver will give same resolution as 2048 PPR / 8192 count encoder)
- Tune motor normally. If motor is always unstable or locks motor position, try changing direction of feedback by toggling checkbox FBI
