Difference between revisions of "DIY SimpleMotion V2 adapter"
| [checked revision] | [checked revision] |
(Created page with "<gallery> IMAG1584.jpg|Needed parts (sold as kit) IMAG1581.jpg|Needed tools IMAG1582.jpg|Stripping insulation of RJ45 cable IMAG1583.jpg|Stripping individual wires of RJ45 cab...") |
|||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | <gallery> | + | It is possible to build [[SimpleMotion V2 compatible communication interface device]] from commonly available parts. This article gives instructions of making one from the parts listed below. |
| − | IMAG1584.jpg|Needed parts | + | |
| − | IMAG1581.jpg|Needed tools | + | *1pcs FTDI's USB to RS485 adapter cable, [http://www.ftdichip.com/Products/Cables/USBRS485.htm USB-RS485-WE-1800-BT] |
| − | IMAG1582.jpg|Stripping insulation of RJ45 cable | + | *1pcs Non-cross linked RJ45 cable (cable will be cut, so one cable is good up to two adapters) |
| − | IMAG1583.jpg|Stripping individual wires of RJ45 cable. Shorten out all except green/white, green and brown. | + | *2pcs 620 to 680 ohm leaded resistors |
| − | IMAG1587.jpg|Making connections with terminal block | + | *1pcs 6 pole terminal block |
| − | IMAG1588.jpg|Securing with cable tie | + | *1pcs cable tie |
| − | IMAG1589.jpg|Final product | + | |
| + | These parts are available from most electronics component distributors, such as Farnell, Mouser and Digikey. | ||
| + | ==Assembly guide== | ||
| + | <gallery widths=400 heights=400> | ||
| + | File:IMAG1584.jpg|Needed parts | ||
| + | File:IMAG1581.jpg|Needed tools | ||
| + | File:IMAG1582.jpg|Stripping insulation of RJ45 cable | ||
| + | File:IMAG1583.jpg|Stripping individual wires of RJ45 cable. Shorten out all except green/white, green and brown. | ||
| + | File:IMAG1587.jpg|Making connections with terminal block | ||
| + | File:IMAG1588.jpg|Securing with cable tie | ||
| + | File:IMAG1589.jpg|Final product | ||
</gallery> | </gallery> | ||
| + | ==Troubleshooting== | ||
| + | If connection to device do not work, or is unstable, check that all wires are well connected to the terminal block. Sometimes terminal block screw may be pressing on wire insulator preventing good electrical contact. Try reconnecting wires if trouble persists. | ||
Latest revision as of 11:13, 17 September 2015
It is possible to build SimpleMotion V2 compatible communication interface device from commonly available parts. This article gives instructions of making one from the parts listed below.
- 1pcs FTDI's USB to RS485 adapter cable, USB-RS485-WE-1800-BT
- 1pcs Non-cross linked RJ45 cable (cable will be cut, so one cable is good up to two adapters)
- 2pcs 620 to 680 ohm leaded resistors
- 1pcs 6 pole terminal block
- 1pcs cable tie
These parts are available from most electronics component distributors, such as Farnell, Mouser and Digikey.
Assembly guide[edit | edit source]
Needed parts
Needed tools
Stripping insulation of RJ45 cable
Stripping individual wires of RJ45 cable. Shorten out all except green/white, green and brown.
Making connections with terminal block
Securing with cable tie
Final product
Troubleshooting[edit | edit source]
If connection to device do not work, or is unstable, check that all wires are well connected to the terminal block. Sometimes terminal block screw may be pressing on wire insulator preventing good electrical contact. Try reconnecting wires if trouble persists.
