Difference between revisions of "IONI power supply schemes"
From Granite Devices Knowledge Wiki
| [checked revision] | [checked revision] |
| (2 intermediate revisions by the same user not shown) | |||
| Line 6: | Line 6: | ||
*Fault tolerant | *Fault tolerant | ||
*Availability of parts | *Availability of parts | ||
| + | *Wide motor supply voltage range possible | ||
|| | || | ||
*Switching PSUs typically don't allow temporary overloading | *Switching PSUs typically don't allow temporary overloading | ||
| Line 19: | Line 20: | ||
*No need for diodes | *No need for diodes | ||
*Linear PSU peak power handling | *Linear PSU peak power handling | ||
| + | *Wide motor supply voltage range possible | ||
|| | || | ||
*Size & weight | *Size & weight | ||
| Line 26: | Line 28: | ||
| [[File:ioni_spu_scheme3.png|300px]] || Single PSU (max 24V) is feeding logic and motor. | | [[File:ioni_spu_scheme3.png|300px]] || Single PSU (max 24V) is feeding logic and motor. | ||
| − | Note: IONICUBEs logic supply can be fed anything between 9 to 24V, however some functionality (mech brake output, VFD output) may not work properly below 24V. If these features are not needed, then also lower voltage can be used. || | + | Note: IONICUBEs logic supply can be fed anything between 9 to 24V, however some functionality (mech brake output, VFD output) may not work properly below 24V. If these features are not needed, then also lower voltage can be used. |
| + | || | ||
*Low cost | *Low cost | ||
*Availability of parts | *Availability of parts | ||
Latest revision as of 21:51, 3 December 2015
| Scheme | Description | Pros | Cons |
|---|---|---|---|
 |
Two switching power supplies, one high power voltage supply for motor and one low power supply for logic circuity. A diode D1 is normally necessary to protect regenerative current flow going back to PSU1. For recommended diodes, see paragraph below. |
|
|
 |
Two similar high power supplies are used to supply both motor and logic voltages. In this system power of PSU1 and PSU2 will contribute to motor supply, i.e. if both supplies are rated 200W, then total power available to drives is ~400W. Diodes D1 is normally needed to protect power supplies from regenerative power and D2/D3 to protect power supplies in the case where one power supply would shut down (i.e. on overload). For recommended diodes, see the paragraph below. |
|
|
 |
Linear (transformer based unregulated) power supply is used for motor supply and low power switching PSU for logic power. |
|
|
 |
Single PSU (max 24V) is feeding logic and motor.
Note: IONICUBEs logic supply can be fed anything between 9 to 24V, however some functionality (mech brake output, VFD output) may not work properly below 24V. If these features are not needed, then also lower voltage can be used. |
|
|
Diodes D1-D3 are typical silicon or schottky rectifier diodes that are sufficiently rated to carry the present voltages and currents. As diodes are inexpensive, there is no need to avoid oversizing them. Examples diodes:
- Diodes Inc. 10A02-T (10A 100V, leaded)
- Diodes Inc. 10A04-T (10A 400V, leaded)
- Fairchild FFPF30UP20STU (30A, 200V, leaded, isolated TO-220 case)
- Fairchild RURG3060 (30A 600V, leaded, non-isolated case - cooling tab is either anode or cathode)
- Fairchild STPS20120D (20A 120V, leaded, non-isolated case - cooling tab is either anode or cathode)
 | Some switching power supplies can tolerate reversed current flow from drive to PSU (renegerative current). In case of such PSU, D1 may be omitted. If unsure about PSU behavior in regeneration, always add D1. |
 | Leaded diodes may be easiest to install right at PSU terminals, no extra wiring needed. |
