Difference between revisions of "Argon user guide/Power supply safe discharging"
From Granite Devices Knowledge Wiki
| [checked revision] | [checked revision] |
| (14 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | Power supplies and drives have capacitors that store electricity even when power supply has been disconnected from the power network. This poses electric shock hazard when touching a device, or its wiring, that has been recently unplugged from the power line. | |
| − | Power supplies and drives have capacitors that store electricity even when power supply has been disconnected from the power network. This poses electric shock hazard when touching a device that has been | + | |
==Safely discharging Argon drive== | ==Safely discharging Argon drive== | ||
[[Argon (servo drive)]] has internal power supply bleeding resistor that will discharge the capacitors during 5 minutes after AC power has been removed. | [[Argon (servo drive)]] has internal power supply bleeding resistor that will discharge the capacitors during 5 minutes after AC power has been removed. | ||
To safely discharge Argon voltages: | To safely discharge Argon voltages: | ||
| − | # Remove | + | # Remove power from J4 connector (both L and N lines). This can be done for example by unplugging the power cord from wall socket where the power comes from. |
| − | # Wait | + | # Wait at least 3 minutes after de-energization to allow capacitor voltage discharge. |
| + | # Measure a DC voltage between VN and VP terminals of J4 connector with a multimeter rated at least up to 600 VDC as the worst case drive internal HV voltage may be over 400 VDC. '''Voltage has been successfully discharged if VN-VP voltage is less than 5 VDC.''' | ||
| + | {{electricshock|If DC voltage between VN and VP terminals of J4 connector is above 20 VDC after 3 minutes of de-energization, drive has internal failure of discharging circuity. In such case danger may be present even after weeks of wait. Contact your supplier first for further assistance before continuing servicing.}} | ||
Discharging 24 VDC supply does happen instantly after 24 V has been removed. However, this does not affect AC side discharge in any way. | Discharging 24 VDC supply does happen instantly after 24 V has been removed. However, this does not affect AC side discharge in any way. | ||
| + | |||
| + | [[Category:Argon_user_guide]] | ||
Latest revision as of 13:17, 7 April 2016
Power supplies and drives have capacitors that store electricity even when power supply has been disconnected from the power network. This poses electric shock hazard when touching a device, or its wiring, that has been recently unplugged from the power line.
Safely discharging Argon drive[edit | edit source]
Argon (servo drive) has internal power supply bleeding resistor that will discharge the capacitors during 5 minutes after AC power has been removed.
To safely discharge Argon voltages:
- Remove power from J4 connector (both L and N lines). This can be done for example by unplugging the power cord from wall socket where the power comes from.
- Wait at least 3 minutes after de-energization to allow capacitor voltage discharge.
- Measure a DC voltage between VN and VP terminals of J4 connector with a multimeter rated at least up to 600 VDC as the worst case drive internal HV voltage may be over 400 VDC. Voltage has been successfully discharged if VN-VP voltage is less than 5 VDC.
 | If DC voltage between VN and VP terminals of J4 connector is above 20 VDC after 3 minutes of de-energization, drive has internal failure of discharging circuity. In such case danger may be present even after weeks of wait. Contact your supplier first for further assistance before continuing servicing. |
Discharging 24 VDC supply does happen instantly after 24 V has been removed. However, this does not affect AC side discharge in any way.
