Difference between revisions of "Template:Param"
From Granite Devices Knowledge Wiki
| [checked revision] | [checked revision] |
| Line 1: | Line 1: | ||
| − | + | {{#switch: {{{1}}} | |
| SMO = SimpleMotion bus address offset | | SMO = SimpleMotion bus address offset | ||
| CM = Control mode | | CM = Control mode | ||
| Line 62: | Line 62: | ||
| TSR = Sample rate | | TSR = Sample rate | ||
| | | | ||
| − | }}}} | + | }} [[{{{1}}}]]<noinclude>[[{{{1}}}]]{{#tip-img:http://granitedevices.com/w/images/f/f0/InfoIcon_16x16.png|{{#switch: {{{1}}} |
| + | | SMO = SimpleMotion bus address offset | ||
| + | | CM = Control mode | ||
| + | | CEN = Require software enable | ||
| + | | CRI = Setpoint input | ||
| + | | MUL = Setpoint multiplier | ||
| + | | DIV = Setpoint divider | ||
| + | | CAL = Acceleration limit | ||
| + | | CVL = Velocity limit | ||
| + | | CRV = Error recovery velocity | ||
| + | | HME = Homing enabled | ||
| + | | MHS = Home switch polarity | ||
| + | | HMI = Index pulse search | ||
| + | | HMH = Hard stop detection threshold | ||
| + | | HMT = Motor current limit during homing | ||
| + | | HMV = Homing velocity limit | ||
| + | | HMA = Homing acceleration limit | ||
| + | | HMF = Offset move after homing | ||
| + | | HFO = Full speed offset move | ||
| + | | HLL = Position soft low limit | ||
| + | | HHL = Position soft high limit | ||
| + | | BDD = Dynamic braking deceleration | ||
| + | | BED = Mech brake engage delay | ||
| + | | BER = Mech brake release delay | ||
| + | | BAP = Mech brake assisted phasing | ||
| + | | CIS = Setpoint smoothing | ||
| + | | AXS = Axis scale | ||
| + | | AXI = Invert direction | ||
| + | | MT = Motor type | ||
| + | | MMS = Maximum speed | ||
| + | | MCC = Continuous current limit | ||
| + | | MMC = Peak current limit | ||
| + | | MR = Coil resistance | ||
| + | | ML = Coil inductance | ||
| + | | MTC = Thermal time constant | ||
| + | | FBD = Feedback device | ||
| + | | FBR = Feedback device resolution | ||
| + | | FBI = Invert feedback direction | ||
| + | | MPC = Pole count | ||
| + | | TBW = Torque bandwidth limit | ||
| + | | KVP = Velocity P gain | ||
| + | | KVI = Velocity I gain | ||
| + | | VFF = Velociity feed-forward gain | ||
| + | | AFF = Acceleration feed-forward gain | ||
| + | | KPP = Position P gain | ||
| + | | PFF = Position feed-forward gain | ||
| + | | FBH = Hall sensors | ||
| + | | FOC = Over current tolerance | ||
| + | | FUV = Under voltage fault threshold | ||
| + | | FOV = Over voltage fault threshold | ||
| + | | FFT = Goal faults filter time | ||
| + | | FPT = Position tracking error threshold | ||
| + | | FVT = Velocity tracking error threshold | ||
| + | | FEV = Over speed fault | ||
| + | | FMO = Motion fault threshold | ||
| + | | LSF = Limit switch function | ||
| + | | TSP1 = Target setpoint 1 | ||
| + | | TSD1 = Delay 1 | ||
| + | | TSP2 = Target setpoint 2 | ||
| + | | TSD2 = Delay 2 | ||
| + | | TSE = Enable test stimulus | ||
| + | | TSR = Sample rate | ||
| + | | | ||
| + | }}}}</noinclude> | ||
Revision as of 20:34, 28 August 2015
[[{{{1}}}]][[{{{1}}}]]
