Argon specifications

This page lists official electrical and physical specifications of the Argon (servo drive).

Mechanical

Property	Value	Units
Dimensions (with wall mounting tabs)¹	51×197×127 (W×H×D)	mm
Dimensions (excluding wall mounting tabs)¹	51×177×127 (W×H×D)	mm
Weight	0.85	kg
Case materials	Steel (cover), aluminum (heat sink)

¹) Wall mounting tabs are fixed part of enclosure

Environment

Property	Value	Units
Operating temperature	10-70	°C
Storage temperature	-30-90	°C
Humidity	0-95 non-condensing	%
Power dissipation	2-100¹	W

¹) Power dissipation is output current and input voltage related.

Power supply

Supply²	Input voltage	Input current typ	Input current max
Logic power	24 VDC +/- 10%	0.1 - 0.4 A	0.5 A
Motor power	85 - 264 VAC 50/60 Hz	0 - 15 A¹	26 A¹
	84 - 380 VDC	0 - 15 A¹	26 A¹

¹) Estimating true current or power consumption based on this table may be difficult as current demand typically varies greatly and and almost completely depends on motor load conditions. ²) Both logic and motor supplies are required.

Motor output

Property	Value	Units	Remarks
Supported motors	AC, BLDC, DC, Linear		Permanent magnet motors only
Continuous output current	0-10	A (peak value, not RMS)	User settable limit
Peak output current	0-15	A (peak value, not RMS)	Duration 1 sec, then returned to continuous limit. User settable current limit.
Switching frequency	17.5	kHz
Maximum modulation depth	88	%	Maximum effective output is 88% of HV DC bus voltage.
Torque control bandwidth	1-3.3	kHz	Motor dependent
Torque control cycle time	57.1	µs
Position & velocity control cycle time	400	µs
Power conversion efficiency	90-95	%	Under typical conditions
Motor inductance range @ 230 VAC	1.4-25	mH
Motor inductance range @ 115 VAC	0.7-25	mH

Regenerative resistor

Property	Value	Units
Maximum current	6	A
Series fuse	8	A
Minimum resistance @ 230 VAC supply	70	Ω
Minimum resistance @ 115 VAC supply	35	Ω
Resistor power dissipation	0-2400¹	W

¹) Power dissipation depends on how much system's kinetic energy is directed to the resistor

Feedback devices

Status of feedback device support

Feedback device type	Status	Electrical interface
Quadrature incremental encoder	Included	Differential 3-5.5V (RS422), Single ended 3-5.5V (CMOS,TTL,open collector)
Hall sensors	Included	Single ended 3-5.5V (CMOS,TTL,open collector). Differential signals accepted.
Analog SinCos encoder	Under development¹	1 V p-p
Resolver/synchro	Under development¹	10 kHz excitation
Serial SSI encoder	Planned¹	RS422/RS485
Serial BiSS encoder	Planned¹	RS422/RS485
Tachogenerator	Planned¹

¹) Supported already by hardware, usage possible after firmware upgrade

Quadrature encoder electrical properties

Property	Value	Units	Remarks
Encoder count rate	0-4	MHz	After 4x decoding, digitally filtered
Supply voltage	4.8-5.2	V	Supplied from drive
Supply current	0-500	mA	Supplied from drive

Inputs / outputs

List of I/O's

• Isolated digital inputs (4 pcs) - used for limit & home switches and clear faults signal ¹
• Isolated digital outputs (4 pcs) - used for status indication ¹
• Differential analog inputs (2 pcs) - used as Analog setpoint ¹
• Differential digital inputs (2 pcs) - used for pulse/direction or second encoder ¹
• Digital inputs (3 pcs) - used for safe torque off and drive enable
• Digital output (1 pcs) - used for motor solenoid brake

¹) Functions may be altered by modifying the Argon open source firmware

Electrical characteristics

For detailed specifications, see I/O electrical interfacing and pinout & wiring.

Property	Value	Units
Isolated digital input (GPIx) logic 1 voltage	3-24	V
Isolated digital input (GPIx) logic 0 voltage	0-1.3	V
Isolated digital output (GPOx) voltage	0-24	V
Isolated digital output (GPOx) current	50	mA
High speed digital input (HSINx) voltage range	2.7-5.5	V
Analog input input (ANAINx) voltage range	±10	V
Analog input input (ANAINx) resolution	12	bits
Enable input input logic 1 voltage	20-25	V
STO input input logic 1 voltage	20-25	V

¹) Power dissipation is output current and input voltage related.

Communication

Property	Value	Units
Communication protocol	SimpleMotion V2
Default bitrate	460800	BPS
Maximum number of Argon devices chained in a single bus	15	pcs
Command throughput	Up to 10000	Commands/s

In no event the Product Information or parts hereof shall be regarded as guarantee of conditions or characteristics. The Product Information or any part thereof may also not be regarded as a warranty of any kind. No liability of any kind shall be assumed by Author with respect to Product Information or any use made by you thereof, nor shall Author indemnify you against or be liable for any third party claims with respect to such information or any use thereof.

As content of this Wiki may be edited by user community, Granite Devices Oy or it's affiliates do not take any responsibility of the contents of this Wiki. Use information at your own risk. However, Granite Devices staff attempts to review all changes made to this Wiki and keep information trustworthy.

Without written consent, Granite Devices' Products or Intellectual Property shall not be used in situations or installations where living beings, material property, or immaterial property could be harmed by the operation, features or failures of Product. Products may only be used in a way where hazards like moving parts, electric shock, laser radiation, or fire can't be realized even if the content of this Wiki would suggest otherwise.