Search results
Create the page "Machine" on this wiki! See also the search results found.
Page title matches
- {{SetGranityTabPageTitle|Machine}}[[File:GranityMachine.png|thumb]] The Machine tab serves following purposes:6 KB (873 words) - 07:21, 19 November 2018
- {{machine|Don't do that}}183 bytes (20 words) - 13:07, 14 August 2013
- #REDIRECT [[Granity user guide/Machine]]40 bytes (5 words) - 19:08, 15 June 2013
- #REDIRECT [[Granity user guide/Machine]]40 bytes (5 words) - 20:48, 28 December 2012
Page text matches
- *Optimized for CNC and machine automation6 KB (771 words) - 10:17, 5 June 2019
- * Prevent machine damage via I²t (motor temperature modeling), blocked motion and tracking e3 KB (369 words) - 08:33, 13 May 2022
- uses = Template:Machine3 KB (357 words) - 00:24, 21 August 2016
- ...(alternating current) servo motor is a 3 phase permanent magnet syncronous machine. This type of motors are driven by 3 wires each driving one phase coil. In3 KB (438 words) - 11:08, 2 October 2015
- ...FB devices are used to get position or velocity information from motor or machine.3 KB (456 words) - 11:31, 10 May 2017
- {{Machine|Disabling drive by software is not reliable enough for emergenecy stopping. {{Machine|Before clicking enable, ensure that no danger is caused by unexpected motor7 KB (1,052 words) - 07:59, 27 April 2017
- ...ld units such as ''revolutions/s''. Make sure [[Granity user guide/Machine|Machine tab]] settings are set-up first to get correct conversion. ...ld units such as ''revolutions/s''. Make sure [[Granity user guide/Machine|Machine tab]] settings are set-up first to get correct conversion.13 KB (2,085 words) - 18:38, 4 January 2021
- {{SetGranityTabPageTitle|Machine}}[[File:GranityMachine.png|thumb]] The Machine tab serves following purposes:6 KB (873 words) - 07:21, 19 November 2018
- ...over current (measured motor phase current above the peak current limit (Machine/MMC) drive allows before entering into fault state. The ''Minimum'' setting ...ld units such as ''revolutions/s''. Make sure [[Granity user guide/Machine|Machine tab]] settings are set-up first to get correct conversion.6 KB (901 words) - 07:24, 19 November 2018
- **Interference escaping from other nearby equipment such as VFD or welding machine3 KB (494 words) - 15:33, 17 June 2016
- {{Machine|Machine danger (safety)}} ...rning¦Template:Caution¦Template:electricshock¦Template:Damage¦Template:Machine4 KB (541 words) - 00:06, 3 July 2016
- {{machine|Don't do that}}183 bytes (20 words) - 13:07, 14 August 2013
- #REDIRECT [[Granity user guide/Machine]]40 bytes (5 words) - 19:08, 15 June 2013
- *[[Granity user guide/Machine|Machine tab]]1 KB (196 words) - 14:31, 16 October 2018
- ...menting with drive parameters is (mostly) safe.''' If motor is attached to machine or bench for testing and nothing is attached to shaft (so motor can't jump ===Machine tab===9 KB (1,349 words) - 16:23, 31 October 2019
- ...enable signals can be configured via [[Granity user guide/Machine|Granity machine tab]]. Logic 1 to these pins is required for drive operation:14 KB (2,063 words) - 12:48, 14 June 2015
- ...k devices|feedback device]], then position of the axis is not known by the machine after system power-on. To acquire absolute position, axis must be driven to2 KB (352 words) - 18:20, 4 January 2021
- #REDIRECT [[Granity user guide/Machine]]40 bytes (5 words) - 22:14, 26 August 2013
- #REDIRECT [[Granity user guide/Machine]]40 bytes (5 words) - 22:14, 26 August 2013
- *Attach motor to the target machine in a position where it can rotate in both directions7 KB (1,142 words) - 22:07, 28 August 2015