ATOMI connectors and pinouts

Legend

Color
Supply pin
Input pin
Output pin

MX, MY, MZ, MA - Motor and encoder connectors

Pin number	Signal name	Usage
1	SW	Limit switch, shared for both directions
2	CHC / Homeswitch	Encoder channel C (index) / homeswitch
3	CHB	Encoder channel B
4	CHA	Encoder channel A
5	+5 V	5 V supply voltage to encoder
6	GND	Encoder supply ground / 0 V
7	PH4	Motor phase 4
8	W / PH3	Motor phase 3 / Servo W
9	V / PH2	Motor phase 2 / Servo V
10	U / PH1	Motor phase 1 / Servo U

X2 - Main setpoint connector

X2 is main control and setpoint signal port consisting Global Enable input signal, Global Fault output signal, pulse and direction/PWM setpoint inputs, and digital outputs for servo ready signals. X2 is directly wired to conform most common parallel port style pulse & direction CNC controllers.

Pin number in header	Pin number in D25 cable	Signal name	Typical usage		Pin number in header	Pin number in D25 cable	Signal name	Typical usage
1	1	ENABLE	Enable all axis (with or without chargepump)		2	14	Homing	Start homing for all axis
3	2	HSIN2_X	Direction input X		4	15	Global_GPO3	Global fault output
5	3	HSIN1_X	Pulse/step input X		6	16	PWM2ANA	PWM to analogue converter input
7	4	HSIN2_Y	Direction input Y		8	17	AUX_IN	Auxilary transistor input
9	5	HSIN1_Y	Pulse/step input Y		10	18	GND	Ground / 0 V
11	6	HSIN2_Z	Direction input Z		12	19	GND
13	7	HSIN1_Z	Pulse/step input Z		14	20	GND
15	8	HSIN2_A	Direction input A		16	21	GND
17	9	HSIN1_A	Pulse/step input A		18	22	GND
19	10	GPO1_XP	X axis servo ready signal		20	23	GND
21	11	GPO1_YP	Y axis servo ready signal		22	24	GND
23	12	GPO1_ZP	Z axis servo ready signal		24	25	GND
25	13	GPO1_AP	A axis servo ready signal		26	N/A	Not connected

Notes:

• All inputs are logic HIGH with input voltage from 2.7 V to 5 V.
• All outputs source 3.3 V with maximum of 8 mA load.

^P) Internal 10 kOhm pull-up resistor.

X3 - Additional setpoint and IO connector

X3 is a second control and setpoint signal port addition to X2. X3 consists of analog setpoint signal inputs and additional digital I/O.

Pin number in header	Pin number in D25 cable	Signal name	Typical usage		Pin number in header	Pin number in D25 cable	Signal name	Typical usage
1	1	GND	GND / 0 V		2	14	+5V	+5 V supply
3	2	GND	GND / 0 V		4	15	Global_IO4	Global IO 4
5	3	AUX_OUT1	Buffered output for AUX_IN		6	16	ANA_OUT	PWM to analogue converter output, 0 to 5 V
7	4	X_GPI2P	Enable positive X travel		8	17	X_GPI3P	Enable negative X travel
9	5	X_GPO4	X position within limits		10	18	X_GPO2	X tracking error
11	6	X_ANAIN	X analogue setpoint input		12	19	Y_GPI2P	Enable positive Y travel
13	7	Y_GPI3P	Enable negative Y travel		14	20	Y_GPO4	Y position within limits
15	8	Y_GPO2	Y tracking error		16	21	Y_ANAIN	Y analogue setpoint input
17	9	Z_GPI2P	Enable positive Z travel		18	22	Z_GPI3P	Enable positive Z travel
19	10	Z_GPO4	Z position within limits		20	23	Z_GPO2	Z tracking error
21	11	Z_ANAIN	Z analogue setpoint input		22	24	A_GPI2P	Enable positive A travel
23	12	A_GPI3P	Enable negative A travel		24	25	A_GPO4	A position within limits
25	13	A_GPO2	A tracking error		26	N/A	A_ANAIN	A analogue setpoint input

Notes:

• All inputs are logic HIGH with input voltage from 2.7 V to 5 V.
• All GPO pins source 3.3 V with maximum of 8 mA load.

¹) Open-drain buffer with 30 V 500 mA maximum rating. Active when AUX_IN = HIGH.

^P) Internal 10 kOhm pull-up resistor.

X4 - Power input and STO connector

X4 is three pin wire terminal for HV DC bus supply and Safe torque off.

Pin number	Signal name	Usage	Electrical
1	GND	Ground
2	STO	Safe torque off	3.3 - 49 V
3	HV+	Motor power supply, HV DC bus	12 - 49 V

JP1 to JP4 - Encoder passthrough connector

JP1 to JP4 are pin headers for external encoder use.

Pin number	Signal name	Usage
1	+5V	+5 V supply
2	CHA	Encoder channel A
3	GND	GND / 0 V
4	CHB	Encoder channel B
5	GND	GND / 0 V
6	CHC	Encoder channel C

In no event the Product Information or parts hereof shall be regarded as guarantee of conditions or characteristics. The Product Information or any part thereof may also not be regarded as a warranty of any kind. No liability of any kind shall be assumed by Author with respect to Product Information or any use made by you thereof, nor shall Author indemnify you against or be liable for any third party claims with respect to such information or any use thereof.

As content of this Wiki may be edited by user community, Granite Devices Oy or it's affiliates do not take any responsibility of the contents of this Wiki. Use information at your own risk. However, Granite Devices staff attempts to review all changes made to this Wiki and keep information trustworthy.

Without written consent, Granite Devices' Products or Intellectual Property shall not be used in situations or installations where living beings, material property, or immaterial property could be harmed by the operation, features or failures of Product. Products may only be used in a way where hazards like moving parts, electric shock, laser radiation, or fire can't be realized even if the content of this Wiki would suggest otherwise.