Editing Acquiring VSD-E/XE fault reason details
Your changes will be displayed to readers once an authorized user accepts them. (help) |
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 1: | Line 1: | ||
This article describes how to use TweakTool to read ''fault location'' parameter from drive to examine the detailed reason of drive fault. | This article describes how to use TweakTool to read ''fault location'' parameter from drive to examine the detailed reason of drive fault. | ||
− | + | ==TweakTool== | |
− | + | ||
Tweak tool is a utily to read/write raw parameters from drive by using the USB adapter. TweakTool can be downloaded from [http://granitedevices.com/assets/files/TweakTool.zip this link]. The application does not require installing, just extract the ZIP file to local disc. | Tweak tool is a utily to read/write raw parameters from drive by using the USB adapter. TweakTool can be downloaded from [http://granitedevices.com/assets/files/TweakTool.zip this link]. The application does not require installing, just extract the ZIP file to local disc. | ||
+ | ===Reading fault location=== | ||
====Preparations==== | ====Preparations==== | ||
#Remove any cable from drive CMD port (the 16 pin flat cable) | #Remove any cable from drive CMD port (the 16 pin flat cable) | ||
Line 8: | Line 8: | ||
#Close GDtool if it's is running | #Close GDtool if it's is running | ||
#Launch TweakTool_1.0.exe | #Launch TweakTool_1.0.exe | ||
− | ====Reading | + | ====Reading ''fault location''==== |
These numbers are referencing to the image below. | These numbers are referencing to the image below. | ||
#Enter 15440 to parameter number | #Enter 15440 to parameter number | ||
Line 16: | Line 16: | ||
[[File:Tweaktool usage.png]] | [[File:Tweaktool usage.png]] | ||
− | + | ==Fault location expanations== | |
− | + | ||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
Line 26: | Line 25: | ||
| 2|| Overcurrent < -24A per phase | | 2|| Overcurrent < -24A per phase | ||
|- | |- | ||
− | | 10 || PLL error | + | | 10 || PLL error |
|- | |- | ||
− | | 15 || Illegal opcode | + | | 15 || Illegal opcode |
|- | |- | ||
− | | 20 || Misalign data | + | | 20 || Misalign data |
|- | |- | ||
− | | 25 || HW stack error | + | | 25 || HW stack error |
|- | |- | ||
− | | 30 || Logic undervoltage < 2.2V | + | | 30 || Logic undervoltage < 2.2V |
|- | |- | ||
− | | 35 || Logic undervoltage < 2.7V | + | | 35 || Logic undervoltage < 2.7V |
|- | |- | ||
− | | 120 || | + | | 120 || Short circuit |
|- | |- | ||
− | | 600 || Overcurrent (user limit | + | | 600 || Overcurrent (user limit) |
|- | |- | ||
− | | 100,110 || Loading config fail | + | | 100,110 || Loading config fail |
|- | |- | ||
− | | | + | | 200,210,220 || Saving config fail |
|- | |- | ||
− | + | | 10000 || No fault location info (this value after normal power-up) | |
− | + | ||
− | + | ||
− | + | ||
− | | 10000 || No fault location info (this value after normal power-up) | + | |
|} | |} | ||
− | |||
− |