Editing Argon firmware 2.0 public beta
Your changes will be displayed to readers once an authorized user accepts them. (help) |
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 1: | Line 1: | ||
− | |||
Argon servo drive firmware version 2.0 public beta is available for evaluation. | Argon servo drive firmware version 2.0 public beta is available for evaluation. | ||
− | The changes | + | The key changes singe 1.4.0 are: |
*New features: | *New features: | ||
− | **Added Position feed-forward gain parameter | + | **Added Position feed-forward gain parameter [[PFF]] - helps to reduce overshoot in position control mode. In previous firmware, this value was fixed to 100%. |
− | ** | + | **Simulated encoder output from internal EXT connector (6 pin header) - useful with resolver systems where external [[controller]] needs encoder count |
**Homing with index pulse search is now possible with resolver feedback device (simulated index pulse at certain resolver angle(s)) | **Homing with index pulse search is now possible with resolver feedback device (simulated index pulse at certain resolver angle(s)) | ||
+ | **Added [[Torque mode application specific attributes]] (rotation angle limit & torque scaling by analog input) | ||
**Added support for ''direction'' input signal in [[PWM]] and Analog setpoint modes | **Added support for ''direction'' input signal in [[PWM]] and Analog setpoint modes | ||
− | + | **[[SimpleMotion V2]] protocol updated: | |
− | **[[SimpleMotion V2]] protocol updated | + | |
***added support for watchdog (stop drive if valid SM commands not arriving within predefined time period) | ***added support for watchdog (stop drive if valid SM commands not arriving within predefined time period) | ||
***calculation of setpoint commands via SM bus renewed (drive setpoint is a sum of phyiscal setpoint (step/dir, pwm, analog etc) and the setpoint from SM host (instant and buffered commands). If SM host sets absolute setpoint, then phyiscal counter (incremental types onle) are reset to zero.) | ***calculation of setpoint commands via SM bus renewed (drive setpoint is a sum of phyiscal setpoint (step/dir, pwm, analog etc) and the setpoint from SM host (instant and buffered commands). If SM host sets absolute setpoint, then phyiscal counter (incremental types onle) are reset to zero.) | ||
Line 16: | Line 15: | ||
**Increased continuous current output limit from 11A to 12.5A and peak current limit from 16A to 18A | **Increased continuous current output limit from 11A to 12.5A and peak current limit from 16A to 18A | ||
**Increased maximum overvoltage level from 382 VDC to 388 VDC | **Increased maximum overvoltage level from 382 VDC to 388 VDC | ||
− | **Support high encoder resolution encoder (up to 4 000 000 PPR, previously was 65 535 PPR) | + | **Support high encoder resolution encoder (up to 4 000 000 PPR, previously was 65 535 PPR) |
**Added new torque bandwidth limit choices: 4700 Hz and Unlimited | **Added new torque bandwidth limit choices: 4700 Hz and Unlimited | ||
− | **[[Phasing a.k.a. phase search]] algorithm | + | **Increased [[Phasing a.k.a. phase search]] algorithm motor swing to allow successful phasing in the case where motor motion is blocked in one direction |
− | + | **Increased speed of [[Phasing a.k.a. phase search]] | |
− | + | ||
− | + | ||
− | + | ||
**Improve fault tolerance with Resolver feedback device | **Improve fault tolerance with Resolver feedback device | ||
− | + | **Added compatibility for Granity 1.7.0 and later | |
− | **Added compatibility for Granity 1. | + | |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + |