Difference between revisions of "Argon user guide/J1 connector wiring"

From Granite Devices Knowledge Wiki
Jump to: navigation, search
[checked revision][checked revision]
(Pin-out)
(Hall sensor)
Line 79: Line 79:
 
! Pin # !! Pin name !! Electrical function || Hall sensor wiring
 
! Pin # !! Pin name !! Electrical function || Hall sensor wiring
 
|-
 
|-
| Shell||PE|| Earth/case || || Feedback cable shield  
+
| Shell||PE|| Earth/case || Feedback cable shield  
 
|-
 
|-
| 1||HALL_W|| Hall sensor input, phase W ||Hall sensor W  
+
| 1||HALL_W|| Hall sensor input, phase W ||Hall sensor W (if differential, then W+ channel)
 
|-
 
|-
| 2||HALL_V|| Hall sensor input, phase V  ||Hall sensor V
+
| 2||HALL_V|| Hall sensor input, phase V  ||Hall sensor V (if differential, then V+ channel)
 
|-
 
|-
| 3||HALL_U|| Hall sensor input, phase U  ||Hall sensor U
+
| 3||HALL_U|| Hall sensor input, phase U  ||Hall sensor U (if differential, then U+ channel)
 
|-
 
|-
| 9|| 5V_OUT||Encoder supply 5V output || || rowspan=2|Encoder supply
+
| 9|| 5V_OUT||Encoder supply 5V output ||Hall sensor supply
 
|-
 
|-
| 10|| GND ||Encoder supply ground ||  
+
| 10|| GND ||Encoder supply ground || Hall sensor ground
 
|}
 
|}
 +
Pins not listed in the table are left open or used for other functions such as Hall sensor.
 
[[Category:Argon]]
 
[[Category:Argon]]
 
[[Category:Setup guides]]
 
[[Category:Setup guides]]

Revision as of 20:33, 8 August 2013

This page lists most common wiring schemes to Argon feedback device ports. For connector pin-outs, see the main article Argon user guide/Wiring.

Incremental encoder

Differential

Differential outputs (RS422 electrical standard) of encoder provides a good EMI immunity and supports long cables with high speed signals. Typical differential encoder has 6-8 wires:

  • Ground
  • Supply
  • Channel A+
  • Channel A-
  • Channel B+
  • Channel B-
  • Index+ channel (optional)
  • Index- channel (optional)

The negative outputs have the inverted (or mirror image) signal of the positive outputs.

J1 pin # Pin name Pin function Encoder wire
Shell PE Earth/case Cable shield
5 CHB- Differential input B- Channel B-
6 CHB+ Differential input B+ Channel B+
7 CHA- Differential input A- Channel A-
8 CHA+ Differential input A+ Channel A+
9 5V_OUT Encoder supply 5V output Encoder supply
10 GND Encoder supply ground Encoder ground
14 CHC- Differential input C- Index- channel
15 CHC+ Differential input C+ Index- channel

Pins not listed in the table are left open or used for other functions such as Hall sensor.

Single ended

Single ended output type is usually one of the following:

  • Open collector outputs
  • TTL outputs
  • CMOS outputs

Typical single ended encoder has 4-5 wires:

  • Ground
  • Supply
  • Channel A
  • Channel B
  • Index channel (optional)
J1 pin # Pin name Pin function Encoder wire
Shell PE Earth/case Cable shield
6 CHB+ Differential input B+ Channel B
8 CHA+ Differential input A+ Channel A
9 5V_OUT Encoder supply 5V output Encoder supply
10 GND Encoder supply ground Encoder ground
15 CHC+ Differential input C+ Index channel

Pins not listed in the table are left open or used for other functions such as Hall sensor.

Hall sensor

Some AC/BLDC/Linear motors are equipped with a Hall sensor which allows faster drive initialization after power-on. Hall sensor is also necessary in the case where motor is not able to move freely in both directions when powered on (i.e. if axis rests at the end of mechanical travel or is vertical axis).

Many Hall sensors have differential outputs (non-inverted and inverted channels, just like differential encoder), however Argon has only single ended Hall sensor inputs which supports both output types (single ended and differential).

It is possible to connect a Hall sensor together with other feedback devices to the same port. In such case supply pins may be shared between multiple FBD's.

Pin # Pin name Electrical function Hall sensor wiring
Shell PE Earth/case Feedback cable shield
1 HALL_W Hall sensor input, phase W Hall sensor W (if differential, then W+ channel)
2 HALL_V Hall sensor input, phase V Hall sensor V (if differential, then V+ channel)
3 HALL_U Hall sensor input, phase U Hall sensor U (if differential, then U+ channel)
9 5V_OUT Encoder supply 5V output Hall sensor supply
10 GND Encoder supply ground Hall sensor ground

Pins not listed in the table are left open or used for other functions such as Hall sensor.