Argon user guide/J5 connector electrical interfacing

From Granite Devices Knowledge Wiki
Jump to: navigation, search

This article explains the internal circuity behind J5 connector of Argon servo drive.

Pin functions

See main article Argon wiring

Pin electrical categories

Supply

Supply pins output a regulated 5V voltage to external circuits. GND pin is tied to J3 connector V- terminal.

Electrical properties
  • Output voltage 4.9-5.2 V
  • Maximum load 500 mA
  • Maximum injected current -10 mA

High speed digital input

Simplified HSIN circuity inside the drive. Left side end represents J5 pins and right side continues to drive internal circuity.

HSIN is differential digital input capable of receiving digital signals up to 4 MHz.

Electrical properties
  • Maximum voltage to HSINx+/- pins referenced to GND: -0.5 to 6V. Nominal 3.3 or 5.0V.
  • Maximum injected current +/- 10 mA
  • When negative input (HSINx-) is left floating, it floats around 2.5V
  • Input state is logic 1 when voltage on positive pin is greater than voltage on negative pin, otherwise it's logic 0
Wiring when driving using differential source
  • Positive outputs of source to HSINx+
  • Negative outputs of source to HSINx-
  • GND must be connected to source ground
Wiring when driving using single ended source (TTL, CMOS or open collector)
  • Outputs of source to HSINx+
  • Leave HSINx- floating
  • GND must be connected to source ground

Analog input

Simplified analog input circuity inside the drive. Left side end represents J5 pins and right side continues to drive internal circuits.

Analog input accepts ±10V from and may be used as reference signal.

Electrical properties
  • Input impedance ~10 kΩ
  • Maximum ANAINx+/- pin voltage vs GND ±20V
  • Maximum injected current ±10 mA
  • Sampling resolution 12 bits
Wiring to differential signal source
  • Connect positive output to ANAINx+
  • Connect negative (inverted) output to ANAINx-
  • Connect source ground to GND
Wiring to single ended signal source
  • Connect output to ANAINx+
  • Connect source ground to ANAINx-
  • Connect source ground to GND

Digital output

Simplified digital output circuity inside the drive. Left side end represents J5 pins and right side continues to drive internal circuits.

Digital output is an optoisolated transistor output to drive various types of inputs of target devices (logic gates, relays, lights etc)

Electrical properties
  • Load voltage range 3-24V
  • Maximum allowed load 50 mA
  • Logic 1 state equals conducting state of optocoupler transistor (current flows from GPO+ to GPO- pins), logic 0 stops current flow between GPO+ to GPO- pins.
  • + to - pin voltage drop at 50 mA less than 2 VDC
Wiring to logic gate input (CMOS or TTL)
  • Connect GPO+ pin to target VCC (typ 5V)
  • Connect GPO- pin to target input pin (so input pin is pulled to 5V when output state is logic 1)

Digital input

Simplified digital input circuity inside the drive. Left side end represents J5 pins and right side continues to drive internal circuits. D27 protects optocoupler from reverse polarity and ESD.

Digital inputs are optoisolated (floating potential) inputs for general purpose control signals.

Electrical properties
  • Signal voltage range 3-24V
  • Logic 0 when difference between +/- inputs less than 1.5V, logic 0 when more than 2.9V
  • Current needed to drive logic 1 is 0.8-9 mA depending on input voltage
  • Maximum voltage difference between GPIx+/- inputs 27 VDC
  • Maximum voltage difference between GPIx+/- inputs vs GND 120 VDC
Connection to electromechanical switch or relay
Connection from electromechanical switch or relay to isolated digital input. PSU may be external power supply or 5V supply from J5 connector.
  • See schematics image in right side
Connection to CMOS source
  • Connect source output to GPIx+ input
  • Connect source ground to GPIx- input
Connection to open collector or TTL source
  • Connect source output to GPIx- input
  • Connect source VCC (typ 5V) to GPOx+ input

Example 1

This example shows how to wire J5 for typical pulse and direction control.

TODO


In no event the Product Information or parts hereof shall be regarded as guarantee of conditions or characteristics. The Product Information or any part thereof may also not be regarded as a warranty of any kind. No liability of any kind shall be assumed by Author with respect to Product Information or any use made by you thereof, nor shall Author indemnify you against or be liable for any third party claims with respect to such information or any use thereof.

As content of this Wiki may be edited by user community, Granite Devices Oy or it's affiliates do not take any responsibility of the contents of this Wiki. Use information at your own risk. However, Granite Devices staff attempts to review all changes made to this Wiki and keep information trustworthy.

Without written consent, Granite Devices' Products or Intellectual Property shall not be used in situations or installations where living beings, material property, or immaterial property could be harmed by the operation, features or failures of Product. Products may only be used in a way where hazards like moving parts, electric shock, laser radiation, or fire can't be realized even if the content of this Wiki would suggest otherwise.