Editing Argon user guide/LED indicators
Your changes will be displayed to readers once an authorized user accepts them. (help) |
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 1: | Line 1: | ||
− | + | Argon has four front panel led indicators which have dedicated indicating tasks: | |
*LD1 SimpleMotion transmit led. Blinks when drive transmits data to bus. | *LD1 SimpleMotion transmit led. Blinks when drive transmits data to bus. | ||
*LD2 SimpleMotion receive led. Blinks when drive receives data from bus. | *LD2 SimpleMotion receive led. Blinks when drive receives data from bus. | ||
Line 8: | Line 8: | ||
*LD3 and LD4 have programmed blinking sequences. Sequences consists series of short (S) and long (L) light pulses. For example LLS means the led will blink two long flashs and then one short flash. After sequence there will be a pause before the sequence repeats. | *LD3 and LD4 have programmed blinking sequences. Sequences consists series of short (S) and long (L) light pulses. For example LLS means the led will blink two long flashs and then one short flash. After sequence there will be a pause before the sequence repeats. | ||
*LD3 and LD4 are independent and can show fault and motor state simultaneously. To easier reading sequence, cover one led with a thumb to be able to concentrate to one led. | *LD3 and LD4 are independent and can show fault and motor state simultaneously. To easier reading sequence, cover one led with a thumb to be able to concentrate to one led. | ||
− | + | ||
==List of all LD3 and LD4 sequences== | ==List of all LD3 and LD4 sequences== | ||
− | To see | + | To see animations, make sure web browser animations are enabled. |
− | === | + | ===High priority faults=== |
Only LD3 is being controlled by these faults. | Only LD3 is being controlled by these faults. | ||
− | |||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
− | + | |Fault reason !! LED sequence || LED sequence as text | |
|- | |- | ||
| Hardware || [[File:3SLLS.gif]] || SLLS | | Hardware || [[File:3SLLS.gif]] || SLLS | ||
Line 31: | Line 30: | ||
| Other/unknown || [[File:3LLSL.gif]] || LLSL | | Other/unknown || [[File:3LLSL.gif]] || LLSL | ||
|} | |} | ||
− | ===Faults | + | ===Faults causing fault stop state=== |
Only LD3 is being controlled by these faults. | Only LD3 is being controlled by these faults. | ||
{| class="wikitable" | {| class="wikitable" | ||
Line 57: | Line 56: | ||
| Motion blocked or motor runaway || [[File:3SLL.gif]] || SSL | | Motion blocked or motor runaway || [[File:3SLL.gif]] || SSL | ||
|- | |- | ||
− | | | + | | Reference range exceeded || [[File:3LSSL.gif]] || LSSL |
|- | |- | ||
− | | Other/unknown | + | | Other/unknown || [[File:3SSSL.gif]] || SSSL |
|} | |} | ||
Line 79: | Line 78: | ||
|- | |- | ||
| Run || [[File:4ON.gif]] || On ||yes | | Run || [[File:4ON.gif]] || On ||yes | ||
− | |||
− | |||
|} | |} | ||
− | |||
− | |||
− |