Editing Argon user guide/Wiring
Your changes will be displayed to readers once an authorized user accepts them. (help) |
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 9: | Line 9: | ||
==Wiring overview== | ==Wiring overview== | ||
[[File:Wiringoverview notitle.png|600px]] | [[File:Wiringoverview notitle.png|600px]] | ||
− | [[File:Argon_test_setup_m.jpg|thumb|A working test setup wiring of Argon. Just connection to a computer and AC power is needed to operate the drive and motor with [[Granity]] or other [[SimpleMotion V2]] app. Note: emergency stopping, [[Argon_user_guide/Earthing|enhanced grounding]], fuse and all recommended | + | [[File:Argon_test_setup_m.jpg|thumb|A working test setup wiring of Argon. Just connection to a computer and AC power is needed to operate the drive and motor with [[Granity]] or other [[SimpleMotion V2]] app. Note: emergency stopping, [[Argon_user_guide/Earthing|enhanced grounding]], fuse and all recommended {{param|EMI}} filters are not installed.]] |
− | [[File:Argon_test_stup_closeup_m.jpg|thumb|A close-up of the test test wiring. Note: emergency stopping, [[Argon_user_guide/Earthing|enhanced grounding]], fuse and all recommended | + | [[File:Argon_test_stup_closeup_m.jpg|thumb|A close-up of the test test wiring. Note: emergency stopping, [[Argon_user_guide/Earthing|enhanced grounding]], fuse and all recommended {{param|EMI}} filters are not installed.]] |
;The minimum wiring for a servo system (after configuration state): | ;The minimum wiring for a servo system (after configuration state): | ||
− | # Safety [[Argon user guide/Earthing|earthing ]]to port J4 | + | # Safety [[Argon user guide/Earthing|earthing ]]to port J4 and preferably to the Argon case |
# 24 VDC wiring to port J3 | # 24 VDC wiring to port J3 | ||
# [[Safe torque off]] and enable signals to port J2. See [[SimpleMotion V2 port|how]]. | # [[Safe torque off]] and enable signals to port J2. See [[SimpleMotion V2 port|how]]. | ||
Line 55: | Line 55: | ||
===J5 Inputs/Outputs=== | ===J5 Inputs/Outputs=== | ||
− | J5 Is a 26 pin [http://en.wikipedia.org/wiki/Insulation-displacement_connector IDC connector] located on the side of Argon. The connector serves as general purpose I/O with [[setpoint signal]] inputs featuring: limit & home switch inputs, status indicator outputs, [[Analog setpoint|analog]], [[Pulse and direction|pulse and direction]], [[quadrature]] or | + | J5 Is a 26 pin [http://en.wikipedia.org/wiki/Insulation-displacement_connector IDC connector] located on the side of Argon. The connector serves as general purpose I/O with [[setpoint signal]] inputs featuring: limit & home switch inputs, status indicator outputs, [[Analog setpoint|analog]], [[Pulse and direction|pulse and direction]], [[quadrature]] or {{param|PWM}} types of [[Setpoint signal|setpoint]] inputs and secondary [[feedback devices|feedback device]] input. |
See the main article [[Argon I/O connector electrical interfacing]] for pin-out and wiring guide. | See the main article [[Argon I/O connector electrical interfacing]] for pin-out and wiring guide. | ||
Line 83: | Line 83: | ||
===Wiring of single drive=== | ===Wiring of single drive=== | ||
[[File:Argonwiringoverview.png|800px]] | [[File:Argonwiringoverview.png|800px]] | ||
− | |||
− |