| Latest revision |
Your text |
| Line 1: |
Line 1: |
| − | [[File:pwm_wiki.png|thumb|PWM signal as setpoint|400px]][[File:pwm_vs_analog.jpg|thumb|Another illustration of PWM nature. On the left side there is a simple circuit for converting analog voltage into PWM signal. Image credit analog.com.|400px]]
| + | PWM a.k.a. Pulse width modulation is a voltage waveform usually seen in power electronics such as motor drives and power supplies. |
| − | PWM a.k.a. pulse-width modulation is a voltage waveform usually seen in power electronics such as motor drives and power supplies. It has been also used as [[setpoint signal]]. | + | |
| | | | |
| − | The main idea in PWM is to switch voltage either fully ''on'' or ''off'' so rapidly that receiving device "feels" only the average voltage caused by pulsed voltage. | + | The main idea in PWM is to switch input voltage either fully on or off so rapidly that output device "feels" only the average voltage caused by pulsed voltage. |
| − | ==Duty cycle== | + | ==Pros and cons== |
| − | Duty cycle describes the ratio of pulse on/off timing. Duty cycle is varied to produce different effective voltages.
| + | ===Pros=== |
| − | | + | |
| − | I.e. if duty cycle is 10%, then the PWM signal is "on" for 10% of time and "off" for 90% of time. I.e. if "on" equals voltage of 48VDC and "off" 0VDC, then 10% duty cycle equals effective voltage of 4.8VDC (48*10% + 0*90% = 4.8).
| + | |
| − | | + | |
| − | ==Frequency==
| + | |
| − | Frequency describes how often on/off states appear in PWM signal. I.e. if PWM frequency is 20 kHz then there will be 20000 "on" and "off" periods per second. Frequency is typically kept constant over time.
| + | |
| − | | + | |
| − | In motor & power control it is typical to use at least 15 kHz PWM frequency to avoid audible high pitched noise that coils produce when driven by PWM.
| + | |
| − | | + | |
| − | ==Usage in GD products==
| + | |
| − | ===As motor output===
| + | |
| − | All GD motor drives produce PWM signal to motor. I.e. if drive supply voltage is 48VDC, then motor output pins will be driven either to 0V or 48V at switching rate of 15-20kHz. VSD drives use MOSFET or IGBT based [http://en.wikipedia.org/wiki/H-Bridge half-bridge] circuits to produce the power PWM output.
| + | |
| − | | + | |
| − | Inductance of motor coils will average the PWM pulses to equivalent DC. If motor inductance is very low, additional inductor is needed between drive and motor phases.
| + | |
| − | ====Pros and cons in drive applications====
| + | |
| − | ;Pros
| + | |
| | * Very high efficiency due to low losses in electronics | | * Very high efficiency due to low losses in electronics |
| − | * Usually very little heat sinking needed
| |
| − | * Easy to produce in digital circuits
| |
| | * Robust | | * Robust |
| − | ;Cons
| + | ===Cons=== |
| − | * Increased [[Electromagnetic interference|EMI noise]] compared to linear voltage | + | * Increased [[Electromagnetic interference||EMI noise]] compared to linear (non-pulsed) output |
| − | * [[Dead-time distortion]]
| + | |
| − | ===As setpoint signal===
| + | |
| − | In some drive models, PWM signal can be used also as [[setpoint signal]] to replace analog signal (the +/- 10V control). In this case PWM voltage is typically 3-5V and the duty cycle of signal determines the amplitude.
| + | |
| − | | + | |
| − | Compared to analog input in VSD products 0% PWM duty cycle equals -10V, 50% equals 0V and 100% equals +10V. Benefits of using PWM instead of analog setpoint:
| + | |
| − | * [[Electromagnetic interference|EMI noise]] tolerant
| + | |
| − | * Easy to galvanically isolate
| + | |
| − | * Easy to generate from digital circuits
| + | |
| − | | + | |
| | ==Links== | | ==Links== |
| | [http://en.wikipedia.org/wiki/Pulse-width_modulation Wikipedia PWM article] | | [http://en.wikipedia.org/wiki/Pulse-width_modulation Wikipedia PWM article] |
| − |
| |
| − | [[Category:Glossary]]
| |
| − | [[Category:Signals]]
| |
