Difference between revisions of "Pulse burst positioning"

From Granite Devices Knowledge Wiki
Jump to: navigation, search
[checked revision][checked revision]
(Created page with "step & direction signals, motor position and move done output as function of time.]] Pulse bu...")
 
Line 1: Line 1:
 
[[File:Burstpulses2.png|379px|thumb|Illustration of input [[Pulse and direction|step & direction]] signals, motor position and move done output as function of time.]]
 
[[File:Burstpulses2.png|379px|thumb|Illustration of input [[Pulse and direction|step & direction]] signals, motor position and move done output as function of time.]]
Pulse burst positioning means a [[setpoint]] signaling based on [[pulse and direction]] format. In burst mode, [[controller]] need only to generate a burst of pulses with direction signal to drive to begin a motion relative to current position complying with pre-configured acceleration and velocity limits.  
+
Pulse burst positioning is a [[setpoint]] method based on [[pulse and direction]] signals. In pulse burst mode, [[controller]] need only to generate a burst of pulses with direction signal to begin a motion relative to current position. Motion will comply with pre-configured acceleration and velocity limits of the drive.  
  
 
;Pulse burst positioning properties
 
;Pulse burst positioning properties
*Simplicity - easy to understand and implement point-to-point motion control
+
*Simplicity - easy to understand and implement point-to-point motion
 +
*No real-time pulse train [[controller]] needed - smooth motion profile is generated inside the drive
 
*Exact - [[setpoint]] signal path is fully digital
 
*Exact - [[setpoint]] signal path is fully digital
*No real-time [[controller]] needed - smooth trajectory is generated inside the drive
+
*Change setpoint on the fly - not necessary to wait for motion to finish before sending new pulses
  
 
==How to use==
 
==How to use==

Revision as of 12:26, 12 December 2013

Illustration of input step & direction signals, motor position and move done output as function of time.

Pulse burst positioning is a setpoint method based on pulse and direction signals. In pulse burst mode, controller need only to generate a burst of pulses with direction signal to begin a motion relative to current position. Motion will comply with pre-configured acceleration and velocity limits of the drive.

Pulse burst positioning properties
  • Simplicity - easy to understand and implement point-to-point motion
  • No real-time pulse train controller needed - smooth motion profile is generated inside the drive
  • Exact - setpoint signal path is fully digital
  • Change setpoint on the fly - not necessary to wait for motion to finish before sending new pulses

How to use

Pulse burst is the minimalistic yet high performing position setpoint method available. Suitable signal may be generated by various means:

  • PLC
  • A simple timer & counter circuit
  • Microcontroller GPIO pin
  • Or any programmable device with controllable digital outputs

Practical example

Drive parameterization

In Argon the following configuration enables burst pulse mode:

  • Set CM as Position control
  • Set CRI as Pulse train & direction
  • Set CAL and CVL to your desired acceleration and velocity values
  • Wire J5 connector according to this diagram

Doing incremental move

The C-style code below represents the signaling.

void IncrementalMove( int distance )
{
  int i;

  /* set direction output pin */
  if(distance<0)
    SetDirectionOutputPin(0);
  else 
    SetDirectionOutputPin(1);

  /* send step pulses to start motion */
  for( i=0; i< abs(distance); i++ )
  {
    Delay_ms(0.001);
    SetPulseOutputPin(1);
    Delay_ms(0.001);
    SetPulseOutputPin(0);
  }
}
  • SetPulseOutputPin sets the digital state of HSIN1 pin on Argon
  • SetDirectionOutputPin sets the digital state of HSIN2 pin on Argon

Monitoring when motion is complete

bool WaitForMoveDone( double timeout )
{
  double waited=0;

  while(waited<timeout)
  {
    if( GetMotionCompletePinState() == true ) 
      return true; /* motion is now complete, return true*/

    /*motion is not complete, wait some time and poll again*/
    Delay_ms(0.01);
    waited=waited+0.01;
  }

  /*return false because timeouted */
  return false;
}
  • GetMotionCompletePinState reads the GPO1 pin state from Argon

Usage example

IncrementalMove(500);
WaitForMoveDone();
IncrementalMove(1000);
WaitForMoveDone();
IncrementalMove(-1500);
WaitForMoveDone();