Difference between revisions of "Signal path of motor drive"
From Granite Devices Knowledge Wiki
| [checked revision] | [checked revision] |
| Line 11: | Line 11: | ||
**Velocity maximum value is limited to [[CVL]] | **Velocity maximum value is limited to [[CVL]] | ||
*Input divider. This divides setpoint signal by [[DIV]] to give desired output scale for ''internal setpoint''. Combination of multiplier and divider can be used change total scaling of setpoint signal. | *Input divider. This divides setpoint signal by [[DIV]] to give desired output scale for ''internal setpoint''. Combination of multiplier and divider can be used change total scaling of setpoint signal. | ||
| + | |||
| + | [[File:Driveblockdiagram setpoint v1.png|900px]] | ||
===Setpoint source scales=== | ===Setpoint source scales=== | ||
| Line 32: | Line 34: | ||
| Serial ([[SimpleMotion V2]]) || Absolute & incremental || Infinite || Direct 1:1 absolute value in all modes | | Serial ([[SimpleMotion V2]]) || Absolute & incremental || Infinite || Direct 1:1 absolute value in all modes | ||
|} | |} | ||
| − | |||
| − | |||
It should be noted that trajectory planner operates after multiplier meaning that [[CVL]] velocity limit value is not in equal scale with velocity setpoint value. | It should be noted that trajectory planner operates after multiplier meaning that [[CVL]] velocity limit value is not in equal scale with velocity setpoint value. | ||
===Internal setpoint=== | ===Internal setpoint=== | ||
| − | Internal setpoint equals the scale of | + | Internal setpoint equals the setpoint and feedback scale of signals in the controller (see below). The scale of feedback signals are: |
*Position feedback: position sensor [[Quadrature|counter]] raw value | *Position feedback: position sensor [[Quadrature|counter]] raw value | ||
*Velocity feedback: number of feedback device [[Quadrature|counts]] per one [[control cycle]]. Obtained by calculating the difference of position feedback values at every control cycle. | *Velocity feedback: number of feedback device [[Quadrature|counts]] per one [[control cycle]]. Obtained by calculating the difference of position feedback values at every control cycle. | ||
Revision as of 13:43, 7 April 2014
In Granite Devices drives the torque, velocity and position limits and setpoints are defined as integer numbers. The vales are represented "hardware" scale which are described below.
Contents
Setpoint signal path
Setpoint signal path converts user setpoint to internal setpoint.
Setpoint signal path
Main parts are:
- Input multiplier. Purpose of this is to increase resolution of input setpoint to allow more fine grained velocity & acceleration control in trajectory planner. By default MUL value is 50.
- Setpoint smoothing filter. If enabled, applies low pass filter to signal reducing jitter and roughness of signal but also introduces about some delay. By default the filter has 100% attenuation at 250Hz.
- Trajectory planner. This limits rate of change of setpoint signal based on CVL and CAL parameters. Output rate maximum rate of change:
- Velocity changes max CAL nubmer of units per control cycle (control cycle is 400µs in most GD drives)
- Velocity maximum value is limited to CVL
- Input divider. This divides setpoint signal by DIV to give desired output scale for internal setpoint. Combination of multiplier and divider can be used change total scaling of setpoint signal.
Setpoint source scales
Different setpoint sources have different range and scale:
| Setpoint source | Type | Range | Scale |
|---|---|---|---|
| Pulse & directon | Incremental | Infinite |
|
| Quadrature | Incremental | Infinite |
|
| PWM | Absolute | Full input scale equals setpoint range of +/-16384 | Direct 1:1 absolute value in all modes |
| Analog | Absolute | Full input scale equals setpoint range of +/-16384 | Direct 1:1 absolute value in all modes |
| Serial (SimpleMotion V2) | Absolute & incremental | Infinite | Direct 1:1 absolute value in all modes |
It should be noted that trajectory planner operates after multiplier meaning that CVL velocity limit value is not in equal scale with velocity setpoint value.
Internal setpoint
Internal setpoint equals the setpoint and feedback scale of signals in the controller (see below). The scale of feedback signals are:
- Position feedback: position sensor counter raw value
- Velocity feedback: number of feedback device counts per one control cycle. Obtained by calculating the difference of position feedback values at every control cycle.
- Torque: hardware specific scale, however Torque scaler knows the hardware scale and scales internal setpoint so that value of +/-16384 represents full torque scale (i.e. internal setpoint value 16384 outputs configured peak current MMC and 8192 outputs MMC/2)
Controller
The default controller type of GD drives is cascaded type where each controlled variable has it's own PI or P controller. In position mode such structure is called as PIV controller.
