Latest revision |
Your text |
Line 8: |
Line 8: |
| | | |
| ==Service manuals== | | ==Service manuals== |
− |
| |
− | '''Note: Review the instructions carefully and only perform service procedures if you feel comfortable performing them. Your reseller will always help if necessary.'''
| |
− |
| |
− | ===Quick Release Pin is too tight or too loose===
| |
− | Problem: The Quick Release Pin is too tight or too easy to remove and QR has play.
| |
− | Possible solution: Adjust the QR pin tightness. See video here: https://www.youtube.com/watch?v=YYKkb5Ioadg
| |
− | ===Quick release slipping===
| |
− | Problem: Wheel/quick release is slipping and center point is changing.
| |
− | Cause: The conical shaft adapter is slipping. This affected many of the very first produced Simucube 2 units in May 2019.
| |
| * {{dlfile|Simucube 2 tightening SQR.pdf|Tightening Simucube Quick Release (solution to slipping) (PDF)}} | | * {{dlfile|Simucube 2 tightening SQR.pdf|Tightening Simucube Quick Release (solution to slipping) (PDF)}} |
− |
| |
− | ===Device stuck at startup===
| |
− | Problem: Device stuck in "Waiting for drive to get ready" and does not start correctly. The E-stop button status follows the real e-stop button.
| |
− | Possible cause: Internal cable for the power button is placed in a bad/sensitive location inside the device.
| |
− | Note: This service instruction is only applicable to Simucube 2 Sport and Pro R1 units (Pro with 2 power supplies) that were produced before August 2020. R1 units have a rocker switch near the one of the rear corners as a power switch, where as R2 units have a on/off toggle switch near the center of the back plate.
| |
− | * {{dlfile|SC2_Sport_&_Pro_R1_power_button_wire_check.pdf|Simucube 2 Sport/Pro R1 power button wire check (PDF)}}
| |
− |
| |
− | ===Antenna connector / cable issues===
| |
− | Problem: The external antenna connector is loose.
| |
− | Cause: Loose antenna connector.
| |
− | '''Note: Do not spin the antenna connector to not cause the internal cable to wind up and break.'''
| |
− | * {{dlfile|SC2_Sport_&_Pro_Antenna_retighten.pdf|Simucube 2 Sport/Pro antenna connection retighten instructions (PDF)}}
| |
− | * {{dlfile|SC2_Ultimate_Antenna_connector_replacement_guide.pdf|Simucube 2 Ultimate antenna connector replacement / re-tightening guide (PDF)}}
| |
− |
| |
− |
| |
− | Problem: Spinning antenna connector has caused the internal antenna cable to break. Solution: Replace the antenna connector&cable assembly. Contact your reseller for spare parts.
| |
− | * {{dlfile|SC2_Sport_&_Pro_R1_Antenna_connector_replacement_guide.pdf|Simucube 2 Sport/Pro R1 antenna connector replacement guide (PDF)}}
| |
− | * {{dlfile|SC2_Sport_&_Pro_R2_Antenna_connector_replacement_guide.pdf|Simucube 2 Sport/Pro R2 antenna connector replacement guide (PDF)}}
| |
− | * {{dlfile|SC2_Ultimate_Antenna_connector_replacement_guide.pdf|Simucube 2 Ultimate antenna connector replacement / re-tightening guide (PDF)}}
| |
| | | |
| ==Developer documentation== | | ==Developer documentation== |
| * {{dlfile|Simucube_2_Accessory_Port_Application_Guide.pdf|Simucube 2 Accessory Port Application Guide (PDF)}} | | * {{dlfile|Simucube_2_Accessory_Port_Application_Guide.pdf|Simucube 2 Accessory Port Application Guide (PDF)}} |
− | * [[Simucube product USB interface documentation]]
| |
− |
| |
− | [[Category:Simucube_2]]
| |