Editing Simucube 2 documentation

This page lists all officially published documentation of Simucube 2 systems. The main Simucube 2 product website is at https:///www.simucu.be

==Software==
see [[Simucube 2 True Drive releases|Simucube 2 True Drive software releases]]

==User manuals==
* {{dlfile|Simucube_2_User_Guide.pdf|Simucube 2 User Guide (PDF)}}

==Service manuals==

'''Note: Review the instructions carefully and only perform service procedures if you feel comfortable performing them. Your reseller will always help if necessary.'''

===Quick release slipping===
Problem: Wheel/quick release is slipping and center point is changing. 
Cause: The conical shaft adapter is slipping. This affected many of the very first produced Simucube 2 units in May 2019.
* {{dlfile|Simucube 2 tightening SQR.pdf|Tightening Simucube Quick Release (solution to slipping) (PDF)}}

===Device stuck at startup===
Problem: Device stuck in "Waiting for drive to get ready" and does not start correctly. The E-stop button status follows the real e-stop button.
Possible cause: Internal cable for the power button is placed in a bad/sensitive location inside the device.
Note: This service instruction is only applicable to Simucube 2 Sport and Pro R1 units (Pro with 2 power supplies) that were produced before August 2020. R1 units have a rocker switch near the one of the rear corners as a power switch, where as R2 units have a on/off toggle switch near the center of the back plate.
* {{dlfile|SC2_Sport_&_Pro_R1_power_button_wire_check.pdf|Simucube 2 Sport/Pro R1 power button wire check (PDF)}}

===Antenna connector / cable issues===
Problem: The external antenna connector is loose.
Cause: Loose antenna connector.
'''Note: Do not spin the antenna connector to not cause the internal cable to wind up and break.'''
* {{dlfile|SC2_Sport_&_Pro_Antenna_retighten.pdf|Simucube 2 Sport/Pro antenna connection retighten instructions (PDF)}}
* {{dlfile|SC2_Ultimate_Antenna_connector_replacement_guide.pdf|Simucube 2 Ultimate antenna connector replacement / re-tightening guide (PDF)}}


Problem: Spinning antenna connector has caused the internal antenna cable to break. Solution: Replace the antenna connector&cable assembly. Contact your reseller for spare parts.
* {{dlfile|SC2_Sport_&_Pro_R1_Antenna_connector_replacement_guide.pdf|Simucube 2 Sport/Pro R1 antenna connector replacement guide (PDF)}}
* {{dlfile|SC2_Sport_&_Pro_R2_Antenna_connector_replacement_guide.pdf|Simucube 2 Sport/Pro R2 antenna connector replacement guide (PDF)}}
* {{dlfile|SC2_Ultimate_Antenna_connector_replacement_guide.pdf|Simucube 2 Ultimate antenna connector replacement / re-tightening guide (PDF)}}

==Developer documentation==
* {{dlfile|Simucube_2_Accessory_Port_Application_Guide.pdf|Simucube 2 Accessory Port Application Guide (PDF)}}
* [[Simucube product USB interface documentation]]
@@ Line 11: / Line 11: @@
 '''Note: Review the instructions carefully and only perform service procedures if you feel comfortable performing them. Your reseller will always help if necessary.'''
-===Quick Release Pin is too tight or too loose===
-Problem: The Quick Release Pin is too tight or too easy to remove and QR has play.
-Possible solution: Adjust the QR pin tightness. See video here: https://www.youtube.com/watch?v=YYKkb5Ioadg
 ===Quick release slipping===
 Problem: Wheel/quick release is slipping and center point is changing.
@@ Line 41: / Line 38: @@
 * {{dlfile|Simucube_2_Accessory_Port_Application_Guide.pdf|Simucube 2 Accessory Port Application Guide (PDF)}}
 * [[Simucube product USB interface documentation]]
-[[Category:Simucube_2]]