Editing Tuning torque controller

{{parent|Servo motor tuning guide}}Torque controller tuning means finding the correct gain values for a torque controller inside the servo drive to achieve a proper response from a torque [[Setpoint signal|setpoint]] change. 

{{info|Torque controller inside drive is implemented by a PI controller where P and I gains are controlled proportionally by {{param|ML}} and {{param|MR}} respectively.}}

==Direct inductance & resistance setting method==
In [[Granity]], there is no dedicated torque control PI gains as the software supports entering motor coil inductance and resistance where the suitable PI gains are calculated from. 

===Method 1 (preferred)===
If you are using a drive model that supports automatic measurement of inductance and resistance, follow the instructions [[Measure motor resistance and inductance in Granity|here]].

===Method 2===
If the above measurement function is not available, and your motor comes with coil specifications containing [[phase-to-phase]] inductance and resistance values, then the only necessary step is to enter the given values into motor {{param|MR}} and {{param|ML}} parameter fields. In case of troubles with this method, proceed with manual tuning method.

==Manual tuning method==
Manual tuning of torque controller is some times done in order to optimize the torque controller response or to find the correct motor {{param|MR}} and {{param|ML}} parameters if unknown. Manual tuning also usually yields better torque response than the direct method which may help tuning of velocity or position tuning.
{{tip|If satisfactory performance was achieved by direct inductance & resistance setting method, you may skip the manual tuning method.}}
In order to change torque tuning, one needs to change motor {{param|MR}} and {{param|ML}} parameters until the torque response looks satisfactory.
===Preparations===
[[File:Torqgoodwithtestingtab.png|thumb|Correct torque tuning settings on the Testing tab.]]
Steps to do to begin torque tuning:
*Ensure that motor is [[Argon user guide/Drive parameterization|parameterized]] correctly and working 
*Fix the motor shaft so that it cannot rotate under full peak torque of the motor
*Make following parameter changes to Granity and click apply afterwards:
**Set drive in torque control mode {{param|CM}}
**Set {{param|TBW}} to maximum 
**Choose ''Serial only'' setpoint input {{param|CM}}
**Untick {{param|CIS}}
**Set Goals tab {{param|DIV}} and {{param|MUL}} to 50
**Make other necessary adjustments to have drive powered and enabled 
*Set-up the test stimulus and capture settings from Testing tab:
**Set target setpoint 1 [[TSP1]] to 2000-15000 (see the chapter below for finding the optimum test setpoint)
**Set delay 1 [[TSD1]] to 0.05 seconds
**Set target setpoint 2 [[TSP2]] to 0
**Set delay1 [[TSD2]] to 0.5 s
**Choose sample rate {{param|TSR}} of 10000 Hz or more
**Choose ''Capture setpoint change ind positive direction'' from the dropdown
**''Tick Continuously repeating capture''
**Tick ''Torque setpoint'' and ''Torque achieved'' from signals
**Tick ''Start capture'' to begin continous capture. 
**Tick {{param|TSE}} to begin a pulsed torque generation

Once the steps above are done, motor should be generating short torque pulses to a fixed shaft and torque response graphs should appear on the right side of Granity about once in 3-5 seconds.
===Finding optimium test current (TSP1)===
To find optimum value for TSP1, enable capture channel called "Motor output voltage" to see how much voltage is driven to motor during rising the edge of torque. For optimum TSP1 value the voltage peak should lie within 20% to 80%. If voltage gets saturated (100%), reduce TSP1 value until it stays below 80%. Images below illustrate the wrong case (first image) and correctly set case (second image).
<gallery widths=400 heights=400>
File:torqueTuningSaturated.png|TSP1 value too high causing output voltage saturation to 100% (A). This will cause torque tuning to look better than it actually is (B).
File:torqueTuningNotSaturated.png|TSP1 value set optimally and peak voltage stays at 60% (C). Now the test reveals that present settings are causing some torque overshooting (D) and we can eliminate it by adjusting ML and MR values.
</gallery>

===Adjusting MR and ML to for optimum torque control===

The task here is to adjust the {{param|MR}} and {{param|ML}} parameters to achieve near optimum step response for the torque controller. Observe the images below for guidance.

{{tip|If the drive faults during this testing due to overcurrent, try reducing [[TSP1]] value or increase {{param|FOC}} parameter. Or try radically different {{param|MR}} and {{param|ML}} values. }}

[[File:TorqlowR.png|800px|]]

In this case the {{param|MR}} value has been set too low causing slowly rising achieved torque curve. Such slow response would reduce servo responsiveness.

[[File:TorqhighR.png|800px|]]

In the opposite case (too high {{param|MR}} value) the response shows wavy oscillations and ovesrhoot.

[[File:TorqlowL.png|800px|]]

Same kind of phenomenon will be seen if motor {{param|ML}} value is too low. Finding oscillation free tuning is finding the correct balance between the MR and ML as both affect each other.

[[File:TorqhigL.png|800px|]]

Too high {{param|ML}} will cause sharp overshooting and high frequency oscillations. Motor may produce audible noise if oscillations are continuous (occurs with way too high ML).

[[File:Torqgood.png|800px|]]

The above image shows near optimum torque response with fast rising edge combined to minimal overshoot.

[[File:Torqgoodspinning.png|800px|]]

The above image shows what may happen if motor shaft is not fixed properly (allowed to rotate). This is withe the optimum settings like the previous image.

===Steps to do after manual tuning finished===
*Stop test stimulus by unticking {{param|TSE}}
*Stop scope catpure by unticking ''Continuously repeating capture''
*Undo all temporary changes made to settings (such as {{param|TBW}}, {{param|CM}}, {{param|DIV}}, {{param|MUL}}) but leave the optimized {{param|MR}} and {{param|ML}} values active
*Save settings to drive memory by clicking ''Save settings on drive non-volatile memory'' button

==Using drive in torque mode==
If torque mode is the final desired operating mode, set-up the [[setpoint]] signal source from Granity Goals tab. Also see [[Signal path of motor drive]] for explanation of torque setpoint scale.
{{next|[[Tuning velocity controller]] - follow if drive will be used in velocity control mode|[[Tuning position controller]] - follow if drive will be used in position control mode }}