Difference between revisions of "Intensify Nx50"

From Granite Devices Knowledge Wiki
Jump to: navigation, search
[checked revision][quality revision]
(Literature)
Line 118: Line 118:
 
|}
 
|}
  
==Literature==
+
==Setup guide==
 
* [[Intensify Nx50 setup guide|Intensify Nx50 setup & user guide]]
 
* [[Intensify Nx50 setup guide|Intensify Nx50 setup & user guide]]
 
[[Category:Laser diode drivers]]
 
[[Category:Laser diode drivers]]

Revision as of 11:57, 10 June 2014

Intensify Nx50
Nx50single.JPG
Device type Laser diode driver
Control modes Current control
Status In production & available from stock
Electrical
DC supply voltage 12 ± 1 VDC
Output current range 0.1 - 50A × number of stacked boards
Setpoint signals Analog reference for current control, Digital signals for enable & pulsing
Protections Over temperature, under voltage, short circuit, ESD, laser diode protection
LD forward voltage 0.8 .. 5.0 VDC
Ripple current (typ @ 50A) 0.2A RMS, 1.25A pk-pk
General
Dimensions 94×77.5×15 mm (3.7"×3.1")
Configuration tool No software tools needed
Web site

Intensify product site

Intensify Nx 50 is a compact stackable constant current laser diode bar driver featuring the latest multiphase switched-mode topology delivering up to 50A continuous current at unforeseen efficiency. Parallel capability allows stacking multiple Intensify boards to scale up the current to 150A and beyond. Intensify is intended for OEM applications such as fiber laser pumping, laser tooling and laser diode burn-in.

Overview

Nx50 is one of the first laser diode drives deploying an state of the art high frequency three-phase switching converter. Each driver has three switching regulator running in separate time phases to minimize output ripple and passive component sizes.

  • Designed for CW/QCW laser bar driving
  • 50 A, 250 W constant output per board
  • Small form factor of 94×77.5 mm / 3.7"×3.1"
  • Parallel by stacking, scale to 150 A and beyond
  • Laser diode current & voltage spike protection
  • Overtemperature, undervoltage, ESD and short circuit proof
  • Fully differential analog 0-10 V setpoint input
  • Current and voltage monitor 0-10 V outputs
  • Pulsing via digital pulse input or analog modulation
  • OEM friendly pricing

Technical specifications

Power

Three Nx50 boards connected parallel by stacking
Nx50 (single board) efficiency vs load current at various laser diode forward voltages
Property Value Units Remarks
Supply voltage 12 ± 1 V
Supply current 0.1 - 23 (1) A Depends on output power
Max output power 250 (1) W 50A @ 5.0V
Output voltage 0.8 - 5.0 V Determined by laser diode voltage drop
Output current 0 - 50 (1) A Continuous rating
Efficiency 95 % Efficiency when IO > 20A and VO = 5V

(1) For single Nx50 board. Multiply this by the number of stacked Nx50 boards.

Timing properties

Property Value Units Remarks
Pulsed LD current rise time 0.5 typ ms Current rise from 10% to 90% of setpoint
Pulsed LD current rise time 0.6 typ ms Current fall from 10% to 90% of setpoint
Enable delay < 60 ms From disabled to enabled state
Disable delay < 2 ms From enabled to disabled state
Power-up/down sequence  Any order. Any I/O line states not causing spiking above setpoint

Inputs/outputs

Property Value Units Remarks
Current setpoint voltage 0..10 V 0..10 V sets LD current between 0..50 A (1)
Current setpoint input impedance 51k (2) Ω Differential input
Current monitor output voltage 0..10 V 0..10 V represents LD current between 0..50 A
Current monitor output impedance ≤ 1k (2) Ω
Voltage monitor output voltage 0..5.0 V Represents LD voltage drop 1:1
Voltage monitor output impedance ≤ 1k (2) Ω
Enable input voltage
  • Logic LOW: -0.3..0.6 V or open circuit = disabled
  • Logic HIGH: 3..26 V = enabled
V Enable is 3.3V, 5V, 12V and 24V logic compatible
Pulse input voltage
  • Logic LOW: -0.3..0.6 V or open circuit (IO=100% of setpoint)
  • Logic HIGH: 3..26 V (IO3.5% of setpoint)
V Pulse is 3.3V, 5V, 12V and 24V logic compatible. Pulse high outputs current defined by setpoint, pulse low outputs current 0.035*setpoint.

(1) For single Nx50 board. Multiply this by the number of stacked Nx50 boards.

(2) For single Nx50 board. Divide this value by the number of stacked Nx50 boards.

Mechanical & environmental

Property Value Units Remarks
Dimensions
  • 94×77.5×15 (PCB)
  • 107×77.5×15 (with J1 hooks)
mm W×H×D
Operating temperature range -40..85 °C Non condensing. Output rating may derate at high temperature without forced convection
Reliability MTBF 1.2 106 Hrs Per Bellcore TR-332 50% stress, Tamb = 40 °C
ESD protection Exceeds ESD Protection to IEC61000-4-2 Level 4, ±12 kV discharge All I/O lines

Setup guide