Difference between revisions of "Intensify Nx50 setup guide"
| [checked revision] | [checked revision] |
(→CMD pin out) |
(→CMD pin out) |
||
| Line 21: | Line 21: | ||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
| − | ! Pin # !! Signal name !! Signal description !! Impedance | + | ! Pin # !! Signal name !! Signal description !! Impedance vs GND |
|- | |- | ||
| 1 || PULSE || Pulse control. When LOW or open, output current is 100% of ISET, when HIGH, output current is 5% of ISET. || 20 kOhm | | 1 || PULSE || Pulse control. When LOW or open, output current is 100% of ISET, when HIGH, output current is 5% of ISET. || 20 kOhm | ||
Revision as of 10:00, 19 February 2013
This is the intallation & user guide for the Intensify Nx50 laser diode driver. Read it through before operating the device.
In case of any questions, please don't hesitate to contact us.
Contents
Physical installation and cooling
Nx50 should be mounted inside an enclosure by using spacer feet attached to the four corner holes.
Nx50 has low power losses due to highly efficient multiphase switching converter technology. Power loss can be calculated by using the offered efficiency data as reference.
In most cases Nx50 is sufficiently cooled with natural convection. This is best achieved by mounting boards vertically and leaving at least 25 mm free air space around both sides.
However, if natural convection does not offer sufficient cooling (i.e. if peak surface temperature is near or exceeds 100°C), then forced convection is necessary. This can be achieved by placing a fan or blower on the side of PCB so that air flow passes along board surface.
Wiring
CMD connector
CMD connector is the user side I/O of the driver. This connector contains the control and feedback signals. All signal lines of the port are ESD protected by dedicated suppressors.
Mating connector type is a 10 pin flat ribbon cable connector with 0.1"/2.54 mm pin pitch and a polarity key. See spec sheet of compatible connector here.
CMD pin out
| Pin # | Signal name | Signal description | Impedance vs GND |
|---|---|---|---|
| 1 | PULSE | Pulse control. When LOW or open, output current is 100% of ISET, when HIGH, output current is 5% of ISET. | 20 kOhm |
| 2 | GNDA | Analog ground | 0 Ohm |
| 3 | IMON+ | Current monitor positive output (differential) | 10 kOhm |
| 4 | IMON- | Current monitor negative output (differential) | 50 kOhm |
| 5 | VMON+ | Voltage monitor positive output (differential) | 10 kOhm |
| 6 | VMON- | Voltage monitor negative output (differential) | 10 kOhm |
| 7 | ISET+ | Current setpoint positive input (differential) | 50 kOhm |
| 8 | ISET- | Current setpoint negateive input (differential) | 50 kOhm |
| 9 | ENABLE | Enable input. When LOW, output enabled and when HIGH or open, output disabled. | 1 kOhm |
| 10 | GND | Power & digital ground | 0 Ohm |
Digital signals
All digital signals (PULSE & ENABLE) are referenced to GND and applicable voltage levels are:
| State | Voltage range |
|---|---|
| Logic LOW | -0.3 .. 0.6V |
| Logic LOW | 3.0 - 7.0 V |
Analog signals
Analog input & output signals support differential signaling to cancel noise and ground loop induced error. These are designed to be compatible with another differential source as well as single ended systems.
Connection to differential 0-10V analog I/O:
| Controller | CMD signal |
|---|---|
| Analog in 1 + | IMON+ |
| Analog in 1 - | IMON- |
| Analog in 2 + | VMON+ |
| Analog in 2 - | VMON- |
| Analog out 1 + | ISET+ |
| Analog out 1 - | ISET- |
| Ground | GND |
Connecting to single ended 0-10V analog I/O. Assuming that I/O is referenced to Ground.
| Controller | CMD signal |
|---|---|
| Analog in 1 | IMON+ |
| Ground | IMON- |
| Analog in 2 | VMON+ |
| Ground | VMON- |
| Analog out 1 | ISET+ |
| Ground | ISET- |
| Ground | GND |
Power
A regulated 12VDC power supply should be connected to hole terminals labeled GND and +12V. Required power is nearly directly proportional to output power plus losses.
For example outputting 40A to 2.0V diode equals output power of 80W. With losses the needed power is about 85-90W which equals 7.0-7.5A @ 12V.
Laser diode
Laser diode is connected to hole terminals labeled O+ and O-. O+ goes to LD anode and 0- to cathode.
