Difference between revisions of "IONICUBE connectors and pinouts"

[checked revision]

Revision as of 10:57, 21 March 2015

Connector layout and naming

Power and feedback ports of X, Y, Z and A axis

Names of power and feedback ports. I.e. X9A means upper floor connector of X9 and X9B the lower floor of X9.

A closeup of X2, X3, X4 and X5

Pin number	Signal name	Usage
1	GND	Ground
2	24V	24V logic supply
3	STO	Safe torque off input (this pin also available in X1, as defined in SimpleMotion V2 port
4	VFD	0-12V analog output where voltage level is proportional to PWM duty cycle on pin PWM on X4. PWM frequency must be between 100 and 10000 Hz.
5	RL1	Relay coil driver output 1. When RLIN1 on X4 is logic high, RL1 is pulled to GND by an open collector circuit. When RLIN1 is low, RL1 is floating (max 24V).
6	RL2	Relay coil driver output 2. When RLIN2 on X4 is logic high, RL2 is pulled to GND by an open collector circuit. When RLIN1 is low, RL2 is floating (max 24V).

Pin number in header	Pin number in D25 cable	Signal name	Typical usage	Pin number in header	Pin number in D25 cable	Signal name	Typical usage
1	1	ENABLE	Enable all axis (with or without chargepump)	2	14	PWM	PWM input for VFD analog output
3	2	HSIN1_X	Direction input X	4	15	GPO4_A	Limit switch output A
5	3	HSIN2_X	Pulse/step input X	6	16	RLIN1	Controls RL1 state
7	4	HSIN1_Y	Direction input Y	8	17	RLIN2	Controls RL2 state
9	5	HSIN2_Y	Pulse/step input Y	10	18	GND	Ground
11	6	HSIN1_Z	Direction input Z	12	19	GND
13	7	HSIN2_Z	Pulse/step input A	14	20	GND
15	8	HSIN1_A	Direction input A	16	21	GND
17	9	HSIN2_A	Pulse/step input A	18	22	GND
19	10	STOP_OUT	Fault on any axis or E-stop (active low)	20	23	GND
21	11	GPO4_X	Limit switch output X	22	24	GND
23	12	GPO4_Y	Limit switch output Y	24	25	GND
25	13	GPO4_Z	Limit switch output Z	26	N/A	Not connected

Pin number in header	Pin number in D25 cable	Signal name	Typical usage	Pin number in header	Pin number in D25 cable	Signal name	Typical usage
1	1	GND		2	14	+5V_OUT	5V supply from IONICUBE ^2
3	2	ANAIN-_X	+/-10V analog input X	4	15	ANAIN+_X	+/-10V analog input X
5	3	ANAIN-_Y	+/-10V analog input Y	6	16	ANAIN+_Y	+/-10V analog input Y
7	4	ANAIN-_Z	+/-10V analog input Z	8	17	ANAIN+_Z	+/-10V analog input Z
9	5	ANAIN-_A	+/-10V analog input A	10	18	ANAIN+_A	+/-10V analog input A
11	6	GPO1_X	For pin function, refer to IONI connector pinout	12	19	GPI4_X	For pin function, refer to IONI connector pinout
13	7	GPO1_Y		14	20	GPI4_Y
15	8	GPO1_Z		16	21	GPI4_Z
17	9	GPO1_A		18	22	GPI4_A
19	10	GPO5_X		20	23	GPI5_X
21	11	GPO5_Y		22	24	GPI5_Y
23	12	GPO5_Z		24	25	GPI5_Z
25	13	GPO5_A		26	N/A	GPI5_A

@@ Line 41: / Line 41: @@
 {| class="wikitable"
 ! Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
-|rowspan=14|
+|rowspan=14 class="tableseparator"|
 !Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
 |-
@@ Line 74: / Line 74: @@
 {| class="wikitable"
 ! Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
-|rowspan=14|
+|rowspan=14 class="tableseparator"|
 !Pin number in header!!Pin number in D25 cable!!Signal name!!Typical usage
 |-