IONI & IONICUBE user guide/Motor compatibility
Contents
Short motor compatibility guide
As motor is not included, make sure that you have, or obtain a motor that is compatible with IONI. Learn more about motor types.
Servo motor requirements
- Permanent magnet brush-DC, AC, brushless or linear motor
- Motor voltage rating 12-60 VDC (IONI supply voltage is 5 - 52 VDC)
- Motor current rating 0.5 - 15A (IONI maximum output is 15A)
- Servo motor must be equipped with an incremental encoder (position sensor) with resolution of 100 to 1000000 pulses per revolution.
Stepping motor requirements
- Two-phase stepping motor with 0.5 - 10A current rating, no feedback device needed. Can be used in position and velocity control mode. Torque mode not possible. Stepper voltage rating is irrelevant, but generally lower voltage & higher current stepper is better.
Unsuitable/non-optimum motors
- Any non-permanent magnet motors: induction AC motor or DC motor with field coil - will not work
- Cheapest grade DC motor, such as one extracted from power drill - might not give satisfying performance
- Motor with very high voltage, such as 200 VAC AC servo motor - it will work if it has incremental encoder feedback, but maximum rotation speed is limited due to drive voltage. We recommend Argon for motors above 100 volts rating.
Detailed compatibility guide
Compatible motor technologies
Motor type must be one of the following (either rotary or linear):
- Permanent magnet brushed DC
- Permanent magnet brushless DC (BLDC) (magnetic pole count 2 to 100)
- Permanent magnet AC (magnetic pole count 2 to 100)
- Stepping motor (2 phase). Stepping motor is driven open loop (no feedback device is utilized).
Compatible feedback devices
Servomotors must be equipped with an compatible feedback devices.
Encoders
If motor is equipped with encoder, following types are compatible:
- Incremental quadrature output type
- Supply voltage 5V
- Single ended or differential wiring
- 2-channel encoder is sufficient for all motor types (index channel and hall sensors are optional)
- Suitable encoder resolutions range from about 100 PPR to 131070 PPR (pulses or lines per revolution)
- Index channel is not required but is supported for precise homing
- Hall or commutation sensors are not required but are supported for AC/BLDC motors
More than 99% if incremental encoders used today are directly compatible with IONI.
Limited compatibility encoders
- Serial data communication based encoders are not currently supported. However if the serial encoder also provides incremental signal outputs, then it can be used as standard incremental encoder with Argon.
- Analog (SinCos) encoder support is partial. At the present mode analog SinCos encoder with 1Vpp output can be connected just like incremental encoder. However at the present state drive will not perform interpolation of analog signal thus not yielding maximum obtainable resolution. The resolution of analog encoder will be the encoder line count multiplied by 4.
Motor power rating
Motor voltages and currents can introduce some limitations to motor output speed and torque but will not cause unsuitability.
- Motor voltage is the limiting factor for maximum speed. For example, if you have a 100 VDC brushed DC servo motor and run it at 50 VDC using IONI, then you can expect to get a speed of 50V/100V = 71% of motor's rated speed.
- Motor current is the limiting factor for maximum torque. For example, if you have motor rated for 20A DC and drive's maximum output is 15A DC, then you get 15=/20A=75% of the rated torque.
Smallest suitable motors
IONI has high dynamic range torque control which makes it suitable also for very small motors, such as ones with rated current around 200 mA.
Need help determining compatibility?
If not sure whether your motor is compatible, you may ask it through Granite Devices support. In inquiry please include details:
- Motor and feedback device manufacturer and part numbers
- Motor and feedback device data sheet or web link to specifications
- Feedback device wiring information (which signals are provided by feedback device)
- Motor current and voltage ratings
In no event the Product Information or parts hereof shall be regarded as guarantee of conditions or characteristics. The Product Information or any part thereof may also not be regarded as a warranty of any kind. No liability of any kind shall be assumed by Author with respect to Product Information or any use made by you thereof, nor shall Author indemnify you against or be liable for any third party claims with respect to such information or any use thereof.
As content of this Wiki may be edited by user community, Granite Devices Oy or it's affiliates do not take any responsibility of the contents of this Wiki. Use information at your own risk. However, Granite Devices staff attempts to review all changes made to this Wiki and keep information trustworthy.
Without written consent, Granite Devices' Products or Intellectual Property shall not be used in situations or installations where living beings, material property, or immaterial property could be harmed by the operation, features or failures of Product. Products may only be used in a way where hazards like moving parts, electric shock, laser radiation, or fire can't be realized even if the content of this Wiki would suggest otherwise.
