Difference between revisions of "ATOMI connectors and pinouts"

From Granite Devices Knowledge Wiki
Jump to: navigation, search
[checked revision][checked revision]
(X1 - Granity and SimpleMotion V2 connector)
Line 18: Line 18:
 
! colspan="3" |Notes / Specifications
 
! colspan="3" |Notes / Specifications
 
|-
 
|-
| 1 || class="inpin" | SW || Limit switch, shared for both directions
+
| 1 || class="inpin" | Limit || Limit switch, shared for both directions
 
| colspan="3" |Internal 2.2 kOhm pull-up resistor
 
| colspan="3" |Internal 2.2 kOhm pull-up resistor
 
|-
 
|-
| 2 || class="inpin" | CHC / Homeswitch || Encoder channel C (index) / homeswitch
+
| 2 || class="inpin" | CHC / Home || Encoder channel C (index) / home switch
 
| colspan="3" |Internal 2.2 kOhm pull-up resistor
 
| colspan="3" |Internal 2.2 kOhm pull-up resistor
 
|-
 
|-
Line 48: Line 48:
 
|Armature +
 
|Armature +
 
|-
 
|-
| 8|| class="outpin" |W / PH3 || Motor phase 3
+
| 8|| class="outpin" |PH3 || Motor phase 3
 
|W (T)
 
|W (T)
 
|Coil B.1
 
|Coil B.1
 
|Armature -
 
|Armature -
 
|-
 
|-
| 9|| class="outpin" |V / PH2 || Motor phase 2
+
| 9|| class="outpin" |PH2 || Motor phase 2
 
|V (S)
 
|V (S)
 
|Coil A.2
 
|Coil A.2
 
|Armature -
 
|Armature -
 
|-
 
|-
| 10|| class="outpin" |U / PH1 || Motor phase 1
+
| 10|| class="outpin" |PH1 || Motor phase 1
 
|U (R)
 
|U (R)
 
|Coil A.1
 
|Coil A.1
Line 132: Line 132:
 
|}
 
|}
 
Notes:
 
Notes:
* All inputs are logic HIGH with input voltage from 2.7 V to 5 V.
+
* Digital inputs accept standard signal levels 2.7 - 5.5 VDC.
* All outputs source 3.3 V with maximum of 8 mA load.
+
* All outputs provide 3.3 V with maximum load of 8 mA.
 
* All GPO pins have a 180 Ohm series resistor.
 
* All GPO pins have a 180 Ohm series resistor.
 
<sup>D</sup>) PWM can be used with or without direction signal. With PWM setpoint without direction signal 50 % PWM = zero setpoint.
 
<sup>D</sup>) PWM can be used with or without direction signal. With PWM setpoint without direction signal 50 % PWM = zero setpoint.
Line 206: Line 206:
 
|}
 
|}
 
Notes:
 
Notes:
* All inputs are logic HIGH with input voltage from 2.7 V to 5 V.
+
* Digital inputs accept standard signal levels 2.7 - 5.5 VDC.
* All GPO pins source 3.3 V with maximum of 8 mA load.
+
* All GPO pins provide 3.3 V with maximum load of 8 mA.
 
* All GPI/O pins have a 180 Ohm series resistor.
 
* All GPI/O pins have a 180 Ohm series resistor.
 
<sup>A</sup>) Setpoint = zero with 50 % input voltage if direction signal is not used.
 
<sup>A</sup>) Setpoint = zero with 50 % input voltage if direction signal is not used.
  
<sup>L</sup>) Limit switches are to wired with NO (normally open) switch to ground. When a limit switch is triggered, movement to the corresponding direction is disabled.
+
<sup>L</sup>) Limit switches are to be wired with NO (normally open) switch to ground. When a limit switch is triggered, movement to the corresponding direction is disabled.
  
 
<sup>P</sup>) Internal 10 kOhm pull-up resistor.
 
<sup>P</sup>) Internal 10 kOhm pull-up resistor.
Line 218: Line 218:
  
 
===X4 - Power input and STO connector===
 
===X4 - Power input and STO connector===
X4 is three pin wire terminal for [[HV DC bus]] supply and [[Safe torque off]].
+
X4 is a wire terminal for [[HV DC bus]] supply and [[Safe torque off]].
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 241: Line 241:
 
|-
 
|-
 
| 2 || class="outpin" |CHA || Encoder channel A
 
| 2 || class="outpin" |CHA || Encoder channel A
|Direct connection to encoder output
+
|Direct connection to encoder output signal
 +
Internal 2.2 kOhm pull-up resistor
 
|-
 
|-
 
| 3 || class="powpin" |GND || GND / 0 V
 
| 3 || class="powpin" |GND || GND / 0 V
Line 247: Line 248:
 
|-
 
|-
 
| 4 || class="outpin" |CHB || Encoder channel B
 
| 4 || class="outpin" |CHB || Encoder channel B
|Direct connection to encoder output
+
|Direct connection to encoder output signal
 +
Internal 2.2 kOhm pull-up resistor
 
|-
 
|-
 
| 5 || class="powpin" |GND || GND / 0 V
 
| 5 || class="powpin" |GND || GND / 0 V
Line 253: Line 255:
 
|-
 
|-
 
| 6 || class="outpin" |CHC || Encoder channel C
 
| 6 || class="outpin" |CHC || Encoder channel C
|Direct connection to encoder output
+
|Direct connection to encoder output signal
 +
Internal 2.2 kOhm pull-up resistor
 
|}
 
|}

Revision as of 11:28, 7 June 2017

Legend

Color
Supply pin
Input pin
Output pin

MX, MY, MZ, MA - Motor and encoder connectors

Pin number Signal name Usage Notes / Specifications
1 Limit Limit switch, shared for both directions Internal 2.2 kOhm pull-up resistor
2 CHC / Home Encoder channel C (index) / home switch Internal 2.2 kOhm pull-up resistor
3 CHB Encoder channel B Internal 2.2 kOhm pull-up resistor
4 CHA Encoder channel A Internal 2.2 kOhm pull-up resistor
5 +5 V 5 V supply voltage to encoder Total 1.5 A current limit for +5 V bus
6 GND Encoder supply ground / 0 V Also ground for cable shield
AC/BLDC motor Stepper motor Brush DC motor
7 PH4 Motor phase 4 - Coil B.2 Armature +
8 PH3 Motor phase 3 W (T) Coil B.1 Armature -
9 PH2 Motor phase 2 V (S) Coil A.2 Armature -
10 PH1 Motor phase 1 U (R) Coil A.1 Armature +

X1 - Granity and SimpleMotion V2 connector

Standard mini-USB connector. Please refer to Granity pages for further instructions.

X2 - Main setpoint connector

X2 is main control and setpoint signal port consisting Global Enable input signal, Global Fault output signal, pulse and direction/PWM setpoint inputs, and digital outputs for servo ready signals. X2 is directly wired to conform most common parallel port style pulse & direction CNC controllers.

Pin number in header Pin number in D25 cable Signal name Typical usage Notes / Specifications Pin number in header Pin number in D25 cable Signal name Typical usage Notes / Specifications
1 1 ENABLE P Enable all axis Active low 2 14 Homing Start homing for all axis Active low
3 2 HSIN2_X Direction input X Direction input for PWM D 4 15 Global_GPO3 P Global fault output Active low
5 3 HSIN1_X Pulse/step input X PWM setpoint 6 16 PWM2ANA PWM to analogue converter input Frequency must be 100 - 10000 Hz
7 4 HSIN2_Y Direction input Y Direction input for PWM D 8 17 AUX_IN Auxilary transistor input Open-drain buffer gate signal.
9 5 HSIN1_Y Pulse/step input Y PWM setpoint 10 18 GND Ground / 0 V -
11 6 HSIN2_Z Direction input Z Direction input for PWM D 12 19 GND -
13 7 HSIN1_Z Pulse/step input Z PWM setpoint 14 20 GND -
15 8 HSIN2_A Direction input A Direction input for PWM D 16 21 GND -
17 9 HSIN1_A Pulse/step input A PWM setpoint 18 22 GND -
19 10 GPO1_X P X axis servo ready signal Active low 20 23 GND -
21 11 GPO1_Y P Y axis servo ready signal Active low 22 24 GND -
23 12 GPO1_Z P Z axis servo ready signal Active low 24 25 GND -
25 13 GPO1_A P A axis servo ready signal Active low 26 N/A GND -

Notes:

  • Digital inputs accept standard signal levels 2.7 - 5.5 VDC.
  • All outputs provide 3.3 V with maximum load of 8 mA.
  • All GPO pins have a 180 Ohm series resistor.

D) PWM can be used with or without direction signal. With PWM setpoint without direction signal 50 % PWM = zero setpoint.

P) Internal 10 kOhm pull-up resistor.

X3 - Additional setpoint and IO connector

X3 is a second control and setpoint signal port addition to X2. X3 consists of analog setpoint signal inputs and additional digital I/O.

Pin number in header Pin number in D25 cable Signal name Typical usage Notes / Specifications Pin number in header Pin number in D25 cable Signal name Typical usage Notes / Specifications
1 1 GND GND / 0 V - 2 14 +5V +5 V supply Total 1.5 A current limit for +5 V bus
3 2 GND GND / 0 V - 4 15 Global_IO4 P Reserved for future use Reserved for future use
5 3 AUX_OUT S Inverter buffer for AUX_IN 24 V 500 mA open-drain buffer.

Active when AUX_IN = HIGH.

6 16 ANA_OUT S VFD speed control signal PWM to analogue converter output.

Output voltage range 0 - 5 V.

7 4 X_GPI2 P Disable positive X travel L Active low 8 17 X_GPI3 P Disable negative X travel L Active low
9 5 X_GPO4 X position within limits Active low 10 18 X_GPO2 X tracking error Active low
11 6 X_ANAIN X analogue setpoint input A 0 - 3.3 V 12 19 Y_GPI2 P Disable positive Y travel L Active low
13 7 Y_GPI3 P Disable negative Y travel L Active low 14 20 Y_GPO4 Y position within limits Active low
15 8 Y_GPO2 Y tracking error Active low 16 21 Y_ANAIN Y analogue setpoint input 0 - 3.3 V A
17 9 Z_GPI2 P Disable positive Z travel L Active low 18 22 Z_GPI3 P Disable negative Z travel L Active low
19 10 Z_GPO4 Z position within limits Active low 20 23 Z_GPO2 Z tracking error Active low
21 11 Z_ANAIN Z analogue setpoint input A 0 - 3.3 V 22 24 A_GPI2 P Disable positive A travel L Active low
23 12 A_GPI3 P Disable negative A travel L Active low 24 25 A_GPO4 A position within limits Active low
25 13 A_GPO2 A tracking error Active low 26 N/A A_ANAIN A analogue setpoint input 0 - 3.3 V A

Notes:

  • Digital inputs accept standard signal levels 2.7 - 5.5 VDC.
  • All GPO pins provide 3.3 V with maximum load of 8 mA.
  • All GPI/O pins have a 180 Ohm series resistor.

A) Setpoint = zero with 50 % input voltage if direction signal is not used.

L) Limit switches are to be wired with NO (normally open) switch to ground. When a limit switch is triggered, movement to the corresponding direction is disabled.

P) Internal 10 kOhm pull-up resistor.

S) Controllable through SimpleMotionV2 bus.

X4 - Power input and STO connector

X4 is a wire terminal for HV DC bus supply and Safe torque off.

Pin number Signal name Usage Notes / Specifications
1 GND Ground -
2 STO Safe torque off 3.3 - 49 V input voltage
3 HV+ Motor power supply, HV DC bus 12 - 49 V, 18 A maximum current through connector

JP1 to JP4 - Encoder passthrough connector

JP1 to JP4 are pin headers for external encoder use.

Pin number Signal name Usage Notes / Specifications
1 +5V +5 V supply Total 1.5 A current limit for +5 V bus
2 CHA Encoder channel A Direct connection to encoder output signal

Internal 2.2 kOhm pull-up resistor

3 GND GND / 0 V -
4 CHB Encoder channel B Direct connection to encoder output signal

Internal 2.2 kOhm pull-up resistor

5 GND GND / 0 V -
6 CHC Encoder channel C Direct connection to encoder output signal

Internal 2.2 kOhm pull-up resistor