Difference between revisions of "Connecting motor to SimuCUBE"

From Granite Devices Knowledge Wiki
Jump to: navigation, search
[checked revision][checked revision]
(Case B: make encoder connection)
Line 96: Line 96:
 
|}
 
|}
  
Refer your motor manufacturer's data sheet/specifications to identify wire colors for encoder signals. Pay ext
+
Refer your motor manufacturer's data sheet/specifications to identify wire colors for encoder signals. Pay extra attention to 5V and GND wiring as miswiring these may cause permanent damage to the encoder.
  
 
===Legend===
 
===Legend===

Revision as of 14:00, 28 June 2016

Connecting motor to SimuCUBE involves wiring motor power and Feedback device (encoder) to the corresponding connectors. This page instructs making these connections properly.

Simucubeboxcabling annotated.jpg

Cabling of SimuCUBE.

  • X1 - 7 pin terminal for motor power and E-stop
  • X16 - Motor feedback device/encoder input
  • X3 - USB connector (HID/game controller)
  • X4 - USB connector (Granity/IONI configuration)
  • AC - 110-240 VAC power inlet
  • X12A & X12B - External button inputs (optional)
  • X13A - Pedal inputs (optional)
  • X11B - External analog inputs (optional)
  • A - E-Stop (normally closed/conducting switch)
  • B - Motor power cable
  • C - Motor encoder cable
  • D - USB to PC (HID/game controller)
  • E - USB to PC (Granity/IONI configuration)
  • F - AC power cord.

Motor power

Motor power cable consists windings and the protective earth conductors. In 3 phase AC servo motor there are four conductors and they should be connected to X1 terminal block according to the table below:

Pin number Signal name Function Usage
1 U / PH1 Motor phase 1 AC servo motor phase U
2 V / PH2 Motor phase 2 AC servo motor phase V
3 W / PH3 Motor phase 3 AC servo motor phase W
4 PH4 Motor phase 4 Used only with 2-phase stepping motor
5 GND Motor protective earth conductor The yellow/green wire
6 E-Stop / STO E-Stop switch input Normall closed (conducting) E-Stop switch goes between pins 6 and 7
7 +5 V 5 VDC output (max 100 mA)

Refer your motor manufacturer's data sheet/specifications to identify wire colors of U, V and W phases.

Motor feedback device

Feedback device (in this case position sensor, usually encoder) need to be connected to SimuCUBE X16 input. X16 connector type on SimuCUBE is D-Sub 15 pin female with two pin rows, so the mating part is D-Sub 15 pin male connector with two pin rows.

Case A: pre-made encoder cable

If you have a motor that comes with pre-made encoder cable with SimuCUBE, IONI or ARGON compatible connector, then simply plug this connector to SimuCUBE X16.


Case B: make encoder connection

If motor encoder cable comes with bare wire ends, or with incompatible connector, then soldering a D-Sub connector with SimuCUBE pin-out is necessary. A, B, and C indicate the quadrature encoder differential signals. C channel is often also denoted as Z, Index or IDX.

Pin # Pin name Electrical type (in most feedback device modes)
Shell GND Earth / 0 V
1 HALL_W Hall sensor digital input W (optional)
2 HALL_V Hall sensor digital input V (optional)
3 HALL_U Hall sensor digital input U (optional)
4 GND Encoder supply ground / 0 V
5 B- Encoder differential input B-
6 B+ Encoder differential input B+
7 A- Encoder differential input A-
8 A+ Encoder differential input A+
9 5V_OUT Encoder supply +5 V output
10 GND Encoder supply ground / 0 V
11 GPI3 no connection
12 GPI2 no connection
13 GPI1 no connection
14 C- Encoder differential input C-
15 C+ Encoder differential input C+

Refer your motor manufacturer's data sheet/specifications to identify wire colors for encoder signals. Pay extra attention to 5V and GND wiring as miswiring these may cause permanent damage to the encoder.

Legend

Colors codes in the pin-out tables:

Color
Supply pin
Input pin
Output pin