Connecting motor to SimuCUBE

From Granite Devices Knowledge Wiki
Revision as of 14:38, 28 June 2016 by Tero K (Talk | contribs)


Jump to: navigation, search

Connecting motor to SimuCUBE involves wiring motor power and Feedback device (encoder) to the corresponding connectors. This page instructs making these connections properly.

Simucubeboxcabling annotated.jpg

Cabling of SimuCUBE.

  • X1 - 7 pin terminal for motor power and E-stop
  • X16 - Motor feedback device/encoder input
  • X3 - USB connector (HID/game controller)
  • X4 - USB connector (Granity/IONI configuration)
  • AC - 110-240 VAC power inlet
  • X12A & X12B - External button inputs (optional)
  • X13A - Pedal inputs (optional)
  • X11B - External analog inputs (optional)
  • A - E-Stop (normally closed/conducting switch)
  • B - Motor power cable
  • C - Motor encoder cable
  • D - USB to PC (HID/game controller)
  • E - USB to PC (Granity/IONI configuration)
  • F - AC power cord.

Motor power

Legend

Colors codes in the pin-out tables:

Color
Supply pin
Input pin
Output pin

Motor power cable consists windings and the protective earth conductors. In 3 phase AC servo motor there are four conductors and they should be connected to X1 terminal block according to the table below:

Pin number Signal name Function Usage
1 U / PH1 Motor phase 1 AC servo motor phase U
2 V / PH2 Motor phase 2 AC servo motor phase V
3 W / PH3 Motor phase 3 AC servo motor phase W
4 PH4 Motor phase 4 Used only with 2-phase stepping motor
5 GND Motor protective earth conductor The yellow/green wire
6 E-Stop / STO E-Stop switch input Normall closed (conducting) E-Stop switch goes between pins 6 and 7
7 +5 V 5 VDC output (max 100 mA)

Refer your motor manufacturer's data sheet/specifications to identify wire colors of U, V and W phases.

Motor feedback device

Feedback device (in this case position sensor, usually encoder) need to be connected to SimuCUBE X16 input. X16 connector type on SimuCUBE is D-Sub 15 pin female with two pin rows, so the mating part is D-Sub 15 pin male connector with two pin rows.


Case A: pre-made encoder cable

If you have a motor that comes with pre-made encoder cable with SimuCUBE, IONI or ARGON compatible connector, then simply plug this connector to SimuCUBE X16.

Case B: make encoder connection

Mating X16 connector to SimuCUBE (D-Sub 15 pins, male, 2 rows, with solder cups)
D-Sub connector hood (15 pin size, 4-40 threaded screws)
If motor encoder cable comes with bare wire ends, or with incompatible connector, then soldering a D-Sub connector with SimuCUBE pin-out is necessary.
Pin # Pin name Electrical type (in most feedback device modes)
Shell GND Cable shield
1 HALL_W Hall sensor digital input W (optional)
2 HALL_V Hall sensor digital input V (optional)
3 HALL_U Hall sensor digital input U (optional)
4 GND Encoder supply ground / 0 V
5 B- Encoder differential input B-
6 B+ Encoder differential input B+
7 A- Encoder differential input A-
8 A+ Encoder differential input A+
9 5V_OUT Encoder supply +5 V output
10 GND Encoder supply ground / 0 V
11 GPI3 no connection
12 GPI2 no connection
13 GPI1 no connection
14 C- Encoder differential input C-
15 C+ Encoder differential input C+

In the table above, A, B, and C indicate the quadrature encoder differential signals. C channel is often also denoted as Z, Index or IDX. Refer your motor manufacturer's data sheet/specifications to identify wire colors for encoder signals. Pay extra attention to 5V and GND wiring as miswiring these may cause permanent damage to the encoder.

Making encoder connector

List of needed items & skills for making the encoder connector:

  • D-Sub connector and connector hood, see List of D-Sub 15 pin connector parts
  • Wire cutters & wire stripping tools
  • Soldering iron
  • Soldering skills
  • Motor manufacturer's data sheet where wire colors and signals are specified

In no event the Product Information or parts hereof shall be regarded as guarantee of conditions or characteristics. The Product Information or any part thereof may also not be regarded as a warranty of any kind. No liability of any kind shall be assumed by Author with respect to Product Information or any use made by you thereof, nor shall Author indemnify you against or be liable for any third party claims with respect to such information or any use thereof.

As content of this Wiki may be edited by user community, Granite Devices Oy or it's affiliates do not take any responsibility of the contents of this Wiki. Use information at your own risk. However, Granite Devices staff attempts to review all changes made to this Wiki and keep information trustworthy.

Without written consent, Granite Devices' Products or Intellectual Property shall not be used in situations or installations where living beings, material property, or immaterial property could be harmed by the operation, features or failures of Product. Products may only be used in a way where hazards like moving parts, electric shock, laser radiation, or fire can't be realized even if the content of this Wiki would suggest otherwise.