Editing IONICUBE 1X
| Your changes will be displayed to readers once an authorized user accepts them. (help) |
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
| Latest revision | Your text | ||
| Line 1: | Line 1: | ||
{{Infobox drive | {{Infobox drive | ||
| name = IONICUBE 1X | | name = IONICUBE 1X | ||
| − | | image=[[File: | + | | image=[[File:cube1x m.jpg|290px]] |
| modelno = IONICUBE 1X | | modelno = IONICUBE 1X | ||
| drivetype = Single axis motherboard for [[IONI]] drives | | drivetype = Single axis motherboard for [[IONI]] drives | ||
| − | | motors = AC, DC, BLDC, Linear | + | | motors = AC, DC, BLDC, Linear |
| controlmodes = Position, Velocity, Torque | | controlmodes = Position, Velocity, Torque | ||
| voltage= Same as [[IONI]] specifications | | voltage= Same as [[IONI]] specifications | ||
| Line 10: | Line 10: | ||
| agencies=CE (EMC & LVD directives) | | agencies=CE (EMC & LVD directives) | ||
| 3dmodel=TBA | | 3dmodel=TBA | ||
| − | |||
| − | |||
}}{{IoniManualNav|width=22em|notoc=1}} | }}{{IoniManualNav|width=22em|notoc=1}} | ||
| Line 21: | Line 19: | ||
*Support mechanical end-of-travel switches and homing switch | *Support mechanical end-of-travel switches and homing switch | ||
*Motor holding brake output with driver | *Motor holding brake output with driver | ||
| − | * | + | *26 pin ribbon cable connector for I/O and [[setpoint]] signals |
*Support 3.3V, 5V and 24V<sup>1</sup> I/O signal levels | *Support 3.3V, 5V and 24V<sup>1</sup> I/O signal levels | ||
| − | * | + | *Charge-pump enable input for safety |
| − | *E-stop switch input ( | + | *E-stop switch input (safe torque off) |
| − | * | + | *[[ARGON Servo Drive]] compatible encoder connector pin-out |
*RJ45 connectors for SimpleMotion V2 usage and configuration | *RJ45 connectors for SimpleMotion V2 usage and configuration | ||
*On-board 0.5A 5V regulator to power drive logic and [[feedback devices]] | *On-board 0.5A 5V regulator to power drive logic and [[feedback devices]] | ||
| Line 31: | Line 29: | ||
==Applications== | ==Applications== | ||
| + | *Robotics | ||
| + | *CNC | ||
*Distributed drive systems | *Distributed drive systems | ||
| − | * | + | *Racing simulators |
| − | + | ||
<sup>1</sup>) 24V I/O needs external components in certain cases | <sup>1</sup>) 24V I/O needs external components in certain cases | ||
| − | |||
==User guide== | ==User guide== | ||
| − | |||
* [[IONI & IONICUBE user guide]] | * [[IONI & IONICUBE user guide]] | ||
* [[IONICUBE 1X connectors and pinouts]] | * [[IONICUBE 1X connectors and pinouts]] | ||
| Line 44: | Line 41: | ||
==See also== | ==See also== | ||
* [[IONICUBE]] - 4 axis motherboard for IONI | * [[IONICUBE]] - 4 axis motherboard for IONI | ||
| − | |||
| − | |||
| − | |||
