Editing Intensify Nx50
Your changes will be displayed to readers once an authorized user accepts them. (help) |
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 3: | Line 3: | ||
| image = [[Image:nx50single.JPG|280px]] | | image = [[Image:nx50single.JPG|280px]] | ||
| controlmodes = Current control | | controlmodes = Current control | ||
− | | production = | + | | production = In production & available from stock |
| voltage = 12 ± 1 VDC | | voltage = 12 ± 1 VDC | ||
| currentrange = 0.1 - 50A × number of stacked boards | | currentrange = 0.1 - 50A × number of stacked boards | ||
+ | | feedbacksignals=On-board current & voltage sensing | ||
| referencesignals=[[Analog reference]] for current control, Digital signals for enable & pulsing | | referencesignals=[[Analog reference]] for current control, Digital signals for enable & pulsing | ||
| configtool=No software tools needed | | configtool=No software tools needed | ||
| url=[http://granitedevices.com/index.php?q=oem-laser-bar-diode-driver Intensify product site] | | url=[http://granitedevices.com/index.php?q=oem-laser-bar-diode-driver Intensify product site] | ||
− | | protections=Over temperature, under voltage, short circuit | + | | protections=Over temperature, under voltage, short circuit, laser diode protection |
− | | dimensions=94×77.5×15 mm | + | | dimensions=94×77.5×15 mm |
| other_label=LD forward voltage | | other_label=LD forward voltage | ||
| other_data=0.8 .. 5.0 VDC | | other_data=0.8 .. 5.0 VDC | ||
| other_label2=Ripple current (typ @ 50A) | | other_label2=Ripple current (typ @ 50A) | ||
− | |||
| other_data2=0.2A RMS, 1.25A pk-pk | | other_data2=0.2A RMS, 1.25A pk-pk | ||
}} | }} | ||
Line 21: | Line 21: | ||
Nx50 is one of the first laser diode drives deploying an state of the art high frequency three-phase switching converter. Each driver has three switching regulator running in separate time phases to minimize output ripple and passive component sizes. | Nx50 is one of the first laser diode drives deploying an state of the art high frequency three-phase switching converter. Each driver has three switching regulator running in separate time phases to minimize output ripple and passive component sizes. | ||
− | * | + | *Ideal for CW/QCW laser bar driving |
*50 A, 250 W constant output per board | *50 A, 250 W constant output per board | ||
− | * | + | *Compliance voltage up to 5.0 V |
*Parallel by stacking, scale to 150 A and beyond | *Parallel by stacking, scale to 150 A and beyond | ||
− | * | + | *Small form factor of 95x77 mm |
− | *Overtemperature, undervoltage | + | *Overtemperature, undervoltage & short circuit proof |
*Fully differential analog 0-10 V [[setpoint]] input | *Fully differential analog 0-10 V [[setpoint]] input | ||
− | *Current and voltage monitor | + | *Current and voltage monitor outputs |
*Pulsing via digital pulse input or analog modulation | *Pulsing via digital pulse input or analog modulation | ||
*OEM friendly pricing | *OEM friendly pricing | ||
Line 50: | Line 50: | ||
| Output current || 0 - 50 <sup>(1)</sup>|| A || Continuous rating | | Output current || 0 - 50 <sup>(1)</sup>|| A || Continuous rating | ||
|- | |- | ||
− | | Efficiency || | + | | Efficiency || 95 ||% || Efficiency when I<sub>o</sub> > 20A and V<sub>o</sub> = 5V |
|} | |} | ||
(1) For single Nx50 board. Multiply this by the number of stacked Nx50 boards. | (1) For single Nx50 board. Multiply this by the number of stacked Nx50 boards. | ||
Line 67: | Line 67: | ||
| Disable delay || < 2 || ms || From enabled to disabled state | | Disable delay || < 2 || ms || From enabled to disabled state | ||
|- | |- | ||
− | | Power-up/down sequence || | + | | Power-up/down sequence || Any order. Any I/O line states not causing spiking above setpoint || || |
|- | |- | ||
|} | |} | ||
===Inputs/outputs=== | ===Inputs/outputs=== | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
Line 97: | Line 90: | ||
| Enable input voltage || | | Enable input voltage || | ||
*Logic LOW: -0.3..0.6 V or open circuit = disabled | *Logic LOW: -0.3..0.6 V or open circuit = disabled | ||
− | *Logic HIGH: | + | *Logic HIGH: 3..26 V = enabled |
− | || V || Enable is 5V, 12V and 24V logic compatible | + | || V || Enable is 3.3V, 5V, 12V and 24V logic compatible |
|- | |- | ||
| Pulse input voltage || | | Pulse input voltage || | ||
*Logic LOW: -0.3..0.6 V or open circuit (I<sub>O</sub>=100% of setpoint) | *Logic LOW: -0.3..0.6 V or open circuit (I<sub>O</sub>=100% of setpoint) | ||
− | *Logic HIGH: | + | *Logic HIGH: 3..26 V (I<sub>O</sub>3.5% of setpoint) |
− | || V || Pulse is 5V, 12V and 24V logic compatible. | + | || V || Pulse is 3.3V, 5V, 12V and 24V logic compatible. Pulse high outputs current defined by [[setpoint]], pulse low outputs current 0.035*setpoint. |
|} | |} | ||
(1) For single Nx50 board. Multiply this by the number of stacked Nx50 boards.<br /> | (1) For single Nx50 board. Multiply this by the number of stacked Nx50 boards.<br /> | ||
Line 126: | Line 119: | ||
|} | |} | ||
− | == | + | ==Literature== |
− | + | ||
− | + | ||
− | + | ||
* [[Intensify Nx50 setup guide|Intensify Nx50 setup & user guide]] | * [[Intensify Nx50 setup guide|Intensify Nx50 setup & user guide]] | ||
− | + | * [http://granitedevices.com/assets/files/flyer/intensify_nx50_flyer.pdf|Nx50 PDF flyer] | |
− | [ | + |