Difference between revisions of "Intensify Nx50 setup guide"

From Granite Devices Knowledge Wiki
Jump to: navigation, search
[checked revision][checked revision]
(Wiring)
Line 7: Line 7:
  
 
Mating connector type is a 10 pin flat ribbon cable connector with 0.1"/2.54 mm pin pitch and a polarity key. See spec sheet of compatible connector [[Media:idc10pin_connector.pdf|here]].
 
Mating connector type is a 10 pin flat ribbon cable connector with 0.1"/2.54 mm pin pitch and a polarity key. See spec sheet of compatible connector [[Media:idc10pin_connector.pdf|here]].
===CMD pin-out===
+
====CMD pin-out====
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 32: Line 32:
 
| 10 || GND|| Power & digital ground
 
| 10 || GND|| Power & digital ground
 
|}
 
|}
===Digital signals===
+
====Digital signals====
 
All digital signals (PULSE & ENABLE) are referenced to GND and applicable voltage levels are:
 
All digital signals (PULSE & ENABLE) are referenced to GND and applicable voltage levels are:
 
{| class="wikitable"
 
{| class="wikitable"
Line 42: Line 42:
 
| Logic high|| 3.0 - 7.0 V
 
| Logic high|| 3.0 - 7.0 V
 
|}
 
|}
===Differential analog signals===
+
====Differential analog signals====
 
Analog input & output signals support [[differential signaling]] to cancel noise and ground loop induced error. These are designed to be compatible with another differential source as well as single ended systems.
 
Analog input & output signals support [[differential signaling]] to cancel noise and ground loop induced error. These are designed to be compatible with another differential source as well as single ended systems.
  
Connection to differential analog I/O:
+
Connection to differential 0-10V analog I/O:
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
 
! Controller !! CMD signal
 
! Controller !! CMD signal
 
|-
 
|-
| Example || IMON+
+
| Analog in 1 +|| IMON+
 
|-
 
|-
| Example || IMON-
+
| Analog in 1 - || IMON-
 
|-
 
|-
| Example || Example
+
| Analog in 2 + || VMON+
 
|-
 
|-
| Example || Example
+
| Analog in 2 - || VMON-
 
|-
 
|-
| Example || Example
+
| Analog out 1 + || ISET+
 
|-
 
|-
| Example || Example
+
| Analog out 1 - || ISET-
 
|-
 
|-
| Example || Example
+
| Ground || GND
 +
|}
 +
Connecting to single ended 0-10V analog I/O. Assuming that I/O is referenced to Ground.
 +
{| class="wikitable"
 +
|-
 +
! Controller !! CMD signal
 +
|-
 +
| Analog in 1 || IMON+
 +
|-
 +
| Ground || IMON-
 +
|-
 +
| Analog in 2 || VMON+
 +
|-
 +
| Ground || VMON-
 +
|-
 +
| Analog out 1 || ISET+
 +
|-
 +
| Ground || ISET-
 
|-
 
|-
| Example || Example
+
| Ground || GND
 
|}
 
|}
 +
===Power===
 +
A regulated 12VDC power supply should be connected to hole terminals labeled GND and +12V. Required power is nearly directly proportional to output power plus losses.
  
 +
For example outputting 40A to 2.0V diode equals output power of 80W. With losses the needed power is about 85-90W which equals 7.0-7.5A @ 12V.
 +
===Laser diode===
 +
Laser diode is connected to hole terminals labeled O+ and O-. O+ goes to LD anode and 0- to cathode.
 
==Connecting parallel==
 
==Connecting parallel==
 
==Usage==
 
==Usage==

Revision as of 20:49, 13 February 2013

Intensify Nx50 PCB from top side

This is the intallation & user guide for the Intensify Nx50 laser diode driver. Read it through before operating the device.

Overview

Wiring

CMD connector

CMD connector is the user side I/O of the driver. This connector contains the control and feedback signals. All signal lines of the port are ESD protected by dedicated suppressors.

Mating connector type is a 10 pin flat ribbon cable connector with 0.1"/2.54 mm pin pitch and a polarity key. See spec sheet of compatible connector here.

CMD pin-out

Header text Header text Header text
1 PULSE Pulse control. When low, output low current and when high, output setpoint current.
2 GNDA Analog ground
3 IMON+ Current monitor positive output (differential)
4 IMON- Current monitor negative output (differential)
5 VMON+ Voltage monitor positive output (differential)
6 VMON- Voltage monitor negative output (differential)
7 ISET+ Current setpoint positive input (differential)
8 ISET- Current setpoint negateive input (differential)
9 ENABLE Enable input. When low, output enabled and high or open, output disabled.
10 GND Power & digital ground

Digital signals

All digital signals (PULSE & ENABLE) are referenced to GND and applicable voltage levels are:

State Voltage range
Logic low -0.3 .. 0.6V
Logic high 3.0 - 7.0 V

Differential analog signals

Analog input & output signals support differential signaling to cancel noise and ground loop induced error. These are designed to be compatible with another differential source as well as single ended systems.

Connection to differential 0-10V analog I/O:

Controller CMD signal
Analog in 1 + IMON+
Analog in 1 - IMON-
Analog in 2 + VMON+
Analog in 2 - VMON-
Analog out 1 + ISET+
Analog out 1 - ISET-
Ground GND

Connecting to single ended 0-10V analog I/O. Assuming that I/O is referenced to Ground.

Controller CMD signal
Analog in 1 IMON+
Ground IMON-
Analog in 2 VMON+
Ground VMON-
Analog out 1 ISET+
Ground ISET-
Ground GND

Power

A regulated 12VDC power supply should be connected to hole terminals labeled GND and +12V. Required power is nearly directly proportional to output power plus losses.

For example outputting 40A to 2.0V diode equals output power of 80W. With losses the needed power is about 85-90W which equals 7.0-7.5A @ 12V.

Laser diode

Laser diode is connected to hole terminals labeled O+ and O-. O+ goes to LD anode and 0- to cathode.

Connecting parallel

Usage

Basic usage

Pulsed usage

Monitoring