Editing SimuCUBE technical specifications

Jump to: navigation, search
Your changes will be displayed to readers once an authorized user accepts them. (help)

Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.

This page supports semantic in-text annotations (e.g. "[[Is specified as::World Heritage Site]]") to build structured and queryable content provided by Semantic MediaWiki. For a comprehensive description on how to use annotations or the #ask parser function, please have a look at the getting started, in-text annotation, or inline queries help page.

Latest revision Your text
Line 1: Line 1:
−
{{SimucubeManualNav}}
+
== Electrical ==
 +
Please refer to [[IONI specifications]] for detailed information of the different [[IONI]] servo drive models.
 +
 
 
== Mechanical ==
 
== Mechanical ==
−
[[file:Simucube_dimensions.png|thumb|left|360px|Dimension drawing]]
+
{{picturebox|Simucube_dimensions.png|800px|caption=SimuCUBE dimensions.}}
  
−
{| class="wikitable"
+
== Enviroment ==
−
!Dimension
+
−
!Length
+
−
|-
+
−
|Width
+
−
|160 mm
+
−
|-
+
−
|Depth
+
−
|87.5 mm
+
−
|-
+
−
|Height
+
−
|< 50 mm (with IONI drive inserted)
+
−
|}
+
−
3D file (simplified):
+
−
* [[media:Simucube_r004_simplified_full.zip|IGS file.]]
+
−
2D PDF and DXF files of the acrylic cases can be found here:
+
−
* [[media:simucube_small_case_pdf_dxf.zip|Small (320 W PSU) acrylic case 2d files, PDF and DXF.]]
+
−
* [[media:simucube_big_case_pdf_dxf.zip|Big (480/720 W PSU) acrylic case 2d files, PDF and DXF.]]
+
−
 
+
−
In case of DIY project to cut the case acrylic components, the acrylic sheet thickness is 4 mm.
+
−
 
+
−
== Environmental ==
+
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 35: Line 16:
 
| Humidity || 0-95 non-condensing || %
 
| Humidity || 0-95 non-condensing || %
 
|}
 
|}
−
Note: on board IONI drive will require forced air flow cooling above 7 A output drive current.
 
  
−
== Electrical ==
+
== Power supply ==
−
=== Power supply ===
+
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
−
! Input voltage  !! Input current when idle !! Input current max
+
! Supply !! Input voltage  !! Input current typ !! Input current max
−
|-
+
−
| 20 - 49 VDC<sup>1</sup> || Typically < 0.4 A
+
−
|Depends on power driven to motor. Up to about 25 A peak consumption is possible. In typical cases 10A @ 48V is sufficient supply.
+
−
|}
+
−
Notes:
+
−
* SimuCUBE has an input diode for reverse input voltage protection
+
−
* Switching mode power supply (SMPS) and linear transformer based power supplies are directly suitable
+
−
 
+
−
===I/O===
+
−
All back face I/O connector pins of SimuCUBE are ESD protected.
+
−
{| class="wikitable"
+
−
|-
+
−
! Property !! Connector/pins !! Value !! Unit
+
−
|-
+
−
| Button connection || X12A/X12B || Switch connected between input pin and GND pin || 
+
−
|-
+
−
| Button input pull-up voltage || X12A/X12B || 3.3 || V
+
−
|-
+
−
| Button input pull-up resistance || X12A/X12B || 3.3 || kOhm
+
−
|-
+
−
| Analog input voltage range || X11A/X11B || 0-3.3 || V
+
−
|-
+
−
| Analog input impedance || X11A/X11B || > 10 || kOhm
+
−
|-
+
−
| Analog input resolution || X11A/X11B || 12 || bits
+
 
|-
 
|-
−
| E-stop / [[Safe torque off]] input connection || X1 pins 6-7 || Normally closed (NC) switch connected between X1 pins 6 and 7 ||  
+
| Motor power || 5 - 56 VDC<sup>1</sup> ||colspan=2| Sum of current consumption of on-board IONI drive
 
|}
 
|}
 +
<sup>1</sup>) Possible to use from 5 VDC upwards, however short circuit protection feature of IONI drive is lost below 12 VDC.
  
−
== Motor control ==
+
SimuCUBE has an input diode for reverse input voltage protection. It also enables the use of switching mode power supplies that would not be able to sink current.
−
SimuCUBE motor control is based on a [[IONI Servo & Stepper Drive]] that plugs on the provided socket. All motor control specifications are identical to IONI drive specifications. Refer to [[IONI specifications]] for details about:
+
−
* Output current ratings
+
−
* Supported [[Feedback devices]]
+
−
* Heat dissipation & cooling
+
−
* Fault protections
+
  
−
[[Category:SimuCUBE]]
+
{{next|[[SimuCUBE user guide/SimuCUBE pinout|Pinout]]}}
−
[[Category:SimuCUBE_user_guide]]
+

Please note that all contributions to Granite Devices Knowledge Wiki may be edited, altered, or removed by other contributors. If you do not want your writing to be edited mercilessly, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource (see Granite Devices Knowledge Wiki:Copyrights for details). Do not submit copyrighted work without permission!

Select categories:

To edit this page, please answer the question that appears below (more info):

Cancel | Editing help (opens in new window)

Template used on this page:

Retrieved from "https://granitedevices.com/wiki/SimuCUBE_technical_specifications"