Search results

Create the page "Machine" on this wiki! See also the search results found.

Page title matches

• Granity user guide/Machine
  {{SetGranityTabPageTitle|Machine}}[[File:GranityMachine.png|thumb]] The Machine tab serves following purposes:
  6 KB (873 words) - 07:21, 19 November 2018
• GDTool 3: Machine
  #REDIRECT [[Granity user guide/Machine]]
  40 bytes (5 words) - 19:08, 15 June 2013
• Granity: Machine
  #REDIRECT [[Granity user guide/Machine]]
  40 bytes (5 words) - 20:48, 28 December 2012

Page text matches

• VSD-E and VSD-XE
  *Optimized for CNC and machine automation
  6 KB (771 words) - 10:17, 5 June 2019
• ARGON Servo Drive
  * Prevent machine damage via I²t (motor temperature modeling), blocked motion and tracking e
  3 KB (369 words) - 08:33, 13 May 2022
• Test page
  uses = Template:Machine
  3 KB (357 words) - 00:24, 21 August 2016
• Motor types
  ...(alternating current) servo motor is a 3 phase permanent magnet syncronous machine. This type of motors are driven by 3 wires each driving one phase coil. In
  3 KB (438 words) - 11:08, 2 October 2015
• Feedback devices
  ...FB devices are used to get position or velocity information from motor or machine.
  3 KB (456 words) - 11:31, 10 May 2017
• Granity user guide/Connect
  {{Machine|Disabling drive by software is not reliable enough for emergenecy stopping. {{Machine|Before clicking enable, ensure that no danger is caused by unexpected motor
  7 KB (1,052 words) - 07:59, 27 April 2017
• Granity user guide/Goals
  ...ld units such as ''revolutions/s''. Make sure [[Granity user guide/Machine|Machine tab]] settings are set-up first to get correct conversion. ...ld units such as ''revolutions/s''. Make sure [[Granity user guide/Machine|Machine tab]] settings are set-up first to get correct conversion.
  13 KB (2,085 words) - 18:38, 4 January 2021
• Granity user guide/Machine
  {{SetGranityTabPageTitle|Machine}}[[File:GranityMachine.png|thumb]] The Machine tab serves following purposes:
  6 KB (873 words) - 07:21, 19 November 2018
• Granity user guide/Fault limits
  ...over current (measured motor phase current above the peak current limit (Machine/MMC) drive allows before entering into fault state. The ''Minimum'' setting ...ld units such as ''revolutions/s''. Make sure [[Granity user guide/Machine|Machine tab]] settings are set-up first to get correct conversion.
  6 KB (901 words) - 07:24, 19 November 2018
• VSD-E/XE connection troubleshooting
  **Interference escaping from other nearby equipment such as VFD or welding machine
  3 KB (494 words) - 15:33, 17 June 2016
• Argon user guide
  {{Machine|Machine danger (safety)}} ...rning¦Template:Caution¦Template:electricshock¦Template:Damage¦Template:Machine
  4 KB (541 words) - 00:06, 3 July 2016
• GDTool 3: Machine
  #REDIRECT [[Granity user guide/Machine]]
  40 bytes (5 words) - 19:08, 15 June 2013
• Granity user guide
  *[[Granity user guide/Machine|Machine tab]]
  1 KB (196 words) - 14:31, 16 October 2018
• Argon user guide/Drive parameterization
  ...menting with drive parameters is (mostly) safe.''' If motor is attached to machine or bench for testing and nothing is attached to shaft (so motor can't jump ===Machine tab===
  9 KB (1,349 words) - 16:23, 31 October 2019
• Argon user guide/J5 connector electrical interfacing
  ...enable signals can be configured via [[Granity user guide/Machine|Granity machine tab]]. Logic 1 to these pins is required for drive operation:
  14 KB (2,063 words) - 12:48, 14 June 2015
• Homing
  ...k devices|feedback device]], then position of the axis is not known by the machine after system power-on. To acquire absolute position, axis must be driven to
  2 KB (352 words) - 18:20, 4 January 2021
• MR
  #REDIRECT [[Granity user guide/Machine]]
  40 bytes (5 words) - 22:14, 26 August 2013
• ML
  #REDIRECT [[Granity user guide/Machine]]
  40 bytes (5 words) - 22:14, 26 August 2013
• Tuning position controller
  *Attach motor to the target machine in a position where it can rotate in both directions
  7 KB (1,142 words) - 22:07, 28 August 2015
• MMC
  #REDIRECT [[Granity user guide/Machine]]
  40 bytes (5 words) - 21:16, 28 August 2013

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)