Difference between revisions of "GraniteCore"
From Granite Devices Knowledge Wiki
| [checked revision] | [checked revision] |
(granitecore variants added) (Tag: VisualEditor) |
|||
| Line 1: | Line 1: | ||
[[File:Argon architecture.jpg|thumb|Argon drive achitecture|400px]] | [[File:Argon architecture.jpg|thumb|Argon drive achitecture|400px]] | ||
| − | GraniteCore a.k.a. GC is the motor control core developed for [[Argon (servo drive)]]. | + | GraniteCore a.k.a. GC is the motor control core developed for Granite Devices motor drives such as [[Argon (servo drive)|Argon]], [[IONI]] and [[ATOMI]]. |
| − | ==Argon architecture== | + | |
| + | == GraniteCore variants == | ||
| + | Due to underlying hardware differences, the GraniteCore has several variants that also have certain differences in functionality and parameterization. | ||
| + | {| class="wikitable" | ||
| + | !GraniteCore variant | ||
| + | !Device models | ||
| + | !Remarks | ||
| + | |- | ||
| + | |G1.0 | ||
| + | |[[VSD-A]] | ||
| + | | | ||
| + | |- | ||
| + | |G1.1 | ||
| + | |[[VSD-E and VSD-XE]] | ||
| + | | | ||
| + | |- | ||
| + | |G2.0 | ||
| + | |[[ARGON]] | ||
| + | |Dual CPU architecture | ||
| + | |- | ||
| + | |G2.1 | ||
| + | |[[IONI]], [[ATOMI]] | ||
| + | |Single ARM CPU architecture | ||
| + | |} | ||
| + | GraniteCore major variant numbers such as G2.x together very similar from user perspective, however some differences exists and these are identified in parameter descriptions in [[Granity user guide]]. | ||
| + | |||
| + | Note that GraniteCore version tied to underlying hardware type, it is ''not'' same as firmware version. | ||
| + | |||
| + | ==About Argon architecture== | ||
Argon consists dual CPU architecture which run in tight synchronism and have different tasks: | Argon consists dual CPU architecture which run in tight synchronism and have different tasks: | ||
;GraniteCore | ;GraniteCore | ||
Revision as of 19:59, 4 March 2017
GraniteCore a.k.a. GC is the motor control core developed for Granite Devices motor drives such as Argon, IONI and ATOMI.
GraniteCore variants
Due to underlying hardware differences, the GraniteCore has several variants that also have certain differences in functionality and parameterization.
| GraniteCore variant | Device models | Remarks |
|---|---|---|
| G1.0 | VSD-A | |
| G1.1 | VSD-E and VSD-XE | |
| G2.0 | ARGON | Dual CPU architecture |
| G2.1 | IONI, ATOMI | Single ARM CPU architecture |
GraniteCore major variant numbers such as G2.x together very similar from user perspective, however some differences exists and these are identified in parameter descriptions in Granity user guide.
Note that GraniteCore version tied to underlying hardware type, it is not same as firmware version.
About Argon architecture
Argon consists dual CPU architecture which run in tight synchronism and have different tasks:
- GraniteCore
- Servo control functionality for torque, velocity and position control
- High dynamic range torque control
- Dead-time distortion correction
- Control power stage directly
- Axis homing functionality
- Virtual scope to capture variables at high sample rate
- Galvanically isolated from I/O side
- Based on Digital Signal Controller
- I/O side CPU
- Feed GraniteCore with real time data consisting
- Position & velocity feedback device data
- State of physical inputs (enable, clear faults, hall sensors etc)
- SimpleMotion V2 commands to read/write parameters
- Interface different types feedback devices and setpoint inputs
- Handle SimpleMotion V2 communication
- Display device state via digital outputs and LED indicators
- Based on ARM Cortex M3 microcontroller running at 120 MHz
Benefits of the architecture
- I/O side CPU has open source firmware allowing end users to implement additional drivers for feedback devices and/or create stand-alone servo drive applications without external Controller.
- Isolation between the processors is more cost efficient and flexible than isolation individual I/O signals directly to high voltage side (a typical solution in the market)
