Difference between revisions of "Simucube 2 documentation"
| [checked revision] | [checked revision] |
(→Antenna connector / cable issues) |
|||
| (4 intermediate revisions by the same user not shown) | |||
| Line 11: | Line 11: | ||
'''Note: Review the instructions carefully and only perform service procedures if you feel comfortable performing them. Your reseller will always help if necessary.''' | '''Note: Review the instructions carefully and only perform service procedures if you feel comfortable performing them. Your reseller will always help if necessary.''' | ||
| + | ===Quick Release Pin is too tight or too loose=== | ||
| + | Problem: The Quick Release Pin is too tight or too easy to remove and QR has play. | ||
| + | Possible solution: Adjust the QR pin tightness. See video here: https://www.youtube.com/watch?v=YYKkb5Ioadg | ||
===Quick release slipping=== | ===Quick release slipping=== | ||
Problem: Wheel/quick release is slipping and center point is changing. | Problem: Wheel/quick release is slipping and center point is changing. | ||
| Line 18: | Line 21: | ||
===Device stuck at startup=== | ===Device stuck at startup=== | ||
Problem: Device stuck in "Waiting for drive to get ready" and does not start correctly. The E-stop button status follows the real e-stop button. | Problem: Device stuck in "Waiting for drive to get ready" and does not start correctly. The E-stop button status follows the real e-stop button. | ||
| − | + | Possible cause: Internal cable for the power button is placed in a bad/sensitive location inside the device. | |
Note: This service instruction is only applicable to Simucube 2 Sport and Pro R1 units (Pro with 2 power supplies) that were produced before August 2020. R1 units have a rocker switch near the one of the rear corners as a power switch, where as R2 units have a on/off toggle switch near the center of the back plate. | Note: This service instruction is only applicable to Simucube 2 Sport and Pro R1 units (Pro with 2 power supplies) that were produced before August 2020. R1 units have a rocker switch near the one of the rear corners as a power switch, where as R2 units have a on/off toggle switch near the center of the back plate. | ||
* {{dlfile|SC2_Sport_&_Pro_R1_power_button_wire_check.pdf|Simucube 2 Sport/Pro R1 power button wire check (PDF)}} | * {{dlfile|SC2_Sport_&_Pro_R1_power_button_wire_check.pdf|Simucube 2 Sport/Pro R1 power button wire check (PDF)}} | ||
| Line 25: | Line 28: | ||
Problem: The external antenna connector is loose. | Problem: The external antenna connector is loose. | ||
Cause: Loose antenna connector. | Cause: Loose antenna connector. | ||
| − | Note: Do not spin the antenna connector to not cause | + | '''Note: Do not spin the antenna connector to not cause the internal cable to wind up and break.''' |
* {{dlfile|SC2_Sport_&_Pro_Antenna_retighten.pdf|Simucube 2 Sport/Pro antenna connection retighten instructions (PDF)}} | * {{dlfile|SC2_Sport_&_Pro_Antenna_retighten.pdf|Simucube 2 Sport/Pro antenna connection retighten instructions (PDF)}} | ||
* {{dlfile|SC2_Ultimate_Antenna_connector_replacement_guide.pdf|Simucube 2 Ultimate antenna connector replacement / re-tightening guide (PDF)}} | * {{dlfile|SC2_Ultimate_Antenna_connector_replacement_guide.pdf|Simucube 2 Ultimate antenna connector replacement / re-tightening guide (PDF)}} | ||
| Line 34: | Line 37: | ||
* {{dlfile|SC2_Sport_&_Pro_R2_Antenna_connector_replacement_guide.pdf|Simucube 2 Sport/Pro R2 antenna connector replacement guide (PDF)}} | * {{dlfile|SC2_Sport_&_Pro_R2_Antenna_connector_replacement_guide.pdf|Simucube 2 Sport/Pro R2 antenna connector replacement guide (PDF)}} | ||
* {{dlfile|SC2_Ultimate_Antenna_connector_replacement_guide.pdf|Simucube 2 Ultimate antenna connector replacement / re-tightening guide (PDF)}} | * {{dlfile|SC2_Ultimate_Antenna_connector_replacement_guide.pdf|Simucube 2 Ultimate antenna connector replacement / re-tightening guide (PDF)}} | ||
| + | |||
| + | ===Firmware update does find the device=== | ||
| + | Problem: Firmware update is stuck after sending command to device, and does not update the device at all. True Drive will just quit after clicking the exit button. | ||
| + | Cause: Razer mouse driver installs a filter driver that blocks the packets used by True Drive to do the update. | ||
| + | * {{dlfile|SC2_Sport&Pro&Ultimate_Firmware_Upgrade_does_not_start.pdf| SC2 Sport&Pro&Ultimate Firmware Upgrade does not start (PDF)}} | ||
| + | |||
| + | |||
| + | ==Using Simucube wheelbase products on Linux== | ||
| + | see: [[Using Simucube wheel base in Linux]] | ||
==Developer documentation== | ==Developer documentation== | ||
Latest revision as of 19:30, 28 May 2024
This page lists all officially published documentation of Simucube 2 systems. The main Simucube 2 product website is at https:///www.simucu.be
Contents
Software[edit | edit source]
see Simucube 2 True Drive software releases
User manuals[edit | edit source]
Service manuals[edit | edit source]
Note: Review the instructions carefully and only perform service procedures if you feel comfortable performing them. Your reseller will always help if necessary.
Quick Release Pin is too tight or too loose[edit | edit source]
Problem: The Quick Release Pin is too tight or too easy to remove and QR has play. Possible solution: Adjust the QR pin tightness. See video here: https://www.youtube.com/watch?v=YYKkb5Ioadg
Quick release slipping[edit | edit source]
Problem: Wheel/quick release is slipping and center point is changing. Cause: The conical shaft adapter is slipping. This affected many of the very first produced Simucube 2 units in May 2019.
Device stuck at startup[edit | edit source]
Problem: Device stuck in "Waiting for drive to get ready" and does not start correctly. The E-stop button status follows the real e-stop button. Possible cause: Internal cable for the power button is placed in a bad/sensitive location inside the device. Note: This service instruction is only applicable to Simucube 2 Sport and Pro R1 units (Pro with 2 power supplies) that were produced before August 2020. R1 units have a rocker switch near the one of the rear corners as a power switch, where as R2 units have a on/off toggle switch near the center of the back plate.
Antenna connector / cable issues[edit | edit source]
Problem: The external antenna connector is loose. Cause: Loose antenna connector. Note: Do not spin the antenna connector to not cause the internal cable to wind up and break.
-
Simucube 2 Sport/Pro antenna connection retighten instructions (PDF) - Simucube 2 Ultimate antenna connector replacement / re-tightening guide (PDF)
Problem: Spinning antenna connector has caused the internal antenna cable to break. Solution: Replace the antenna connector&cable assembly. Contact your reseller for spare parts.
- Simucube 2 Sport/Pro R1 antenna connector replacement guide (PDF)
- Simucube 2 Sport/Pro R2 antenna connector replacement guide (PDF)
- Simucube 2 Ultimate antenna connector replacement / re-tightening guide (PDF)
Firmware update does find the device[edit | edit source]
Problem: Firmware update is stuck after sending command to device, and does not update the device at all. True Drive will just quit after clicking the exit button. Cause: Razer mouse driver installs a filter driver that blocks the packets used by True Drive to do the update.
Using Simucube wheelbase products on Linux[edit | edit source]
see: Using Simucube wheel base in Linux
