Difference between revisions of "Simucube 2 documentation"

From Granite Devices Knowledge Wiki
Jump to: navigation, search
[checked revision][checked revision]
(→‎Service manuals)
(→‎Service manuals)
Line 11: Line 11:
 
'''Note: Review the instructions carefully and only perform service procedures if you feel comfortable performing them. Your reseller will always help if necessary.'''
 
'''Note: Review the instructions carefully and only perform service procedures if you feel comfortable performing them. Your reseller will always help if necessary.'''
  
−
Problem: Wheel is slipping and center point is changing.  
+
===Quick release slipping===
 +
Problem: Wheel/quick release is slipping and center point is changing.  
 
Cause: The conical shaft adapter is slipping. This affected many of the very first produced Simucube 2 units in May 2019.
 
Cause: The conical shaft adapter is slipping. This affected many of the very first produced Simucube 2 units in May 2019.
 
* {{dlfile|Simucube 2 tightening SQR.pdf|Tightening Simucube Quick Release (solution to slipping) (PDF)}}
 
* {{dlfile|Simucube 2 tightening SQR.pdf|Tightening Simucube Quick Release (solution to slipping) (PDF)}}
  
−
 
+
===Device stuck at startup===
 
Problem: Device stuck in "Waiting for drive to get ready" and does not start correctly. The E-stop button status follows the real e-stop button.
 
Problem: Device stuck in "Waiting for drive to get ready" and does not start correctly. The E-stop button status follows the real e-stop button.
 
Cause: Internal cable for the power button is placed in a bad location inside the device.
 
Cause: Internal cable for the power button is placed in a bad location inside the device.
Line 21: Line 22:
 
* {{dlfile|SC2_Sport_&_Pro_R1_power_button_wire_check.pdf|Simucube 2 Sport/Pro R1 power button wire check (PDF)}}
 
* {{dlfile|SC2_Sport_&_Pro_R1_power_button_wire_check.pdf|Simucube 2 Sport/Pro R1 power button wire check (PDF)}}
  
−
 
+
===Antenna connector / cable issues===
 
Problem: The external antenna connector is loose.
 
Problem: The external antenna connector is loose.
 
Cause: Loose antenna connector.
 
Cause: Loose antenna connector.

Revision as of 16:45, 25 January 2021

This page lists all officially published documentation of Simucube 2 systems. The main Simucube 2 product website is at https:///www.simucu.be

Software

see Simucube 2 True Drive software releases

User manuals

Service manuals

Note: Review the instructions carefully and only perform service procedures if you feel comfortable performing them. Your reseller will always help if necessary.

Quick release slipping

Problem: Wheel/quick release is slipping and center point is changing. Cause: The conical shaft adapter is slipping. This affected many of the very first produced Simucube 2 units in May 2019.

Device stuck at startup

Problem: Device stuck in "Waiting for drive to get ready" and does not start correctly. The E-stop button status follows the real e-stop button. Cause: Internal cable for the power button is placed in a bad location inside the device. Note: This service instruction is only applicable to Simucube 2 Sport and Pro R1 units (Pro with 2 power supplies) that were produced before August 2020. R1 units have a rocker switch near the one of the rear corners as a power switch, where as R2 units have a on/off toggle switch near the center of the back plate.

Antenna connector / cable issues

Problem: The external antenna connector is loose. Cause: Loose antenna connector. Note: Do not spin the antenna connector to not cause it to wind up and break.


Problem: Spinning antenna connector has caused the internal antenna cable to break. Solution: Replace the antenna connector&cable assembly. Contact your reseller for spare parts.

Developer documentation

Retrieved from "https://granitedevices.com/w/index.php?title=Simucube_2_documentation&oldid=7443"