Search results
Create the page "Software" on this wiki! See also the search results found.
Page title matches
Page text matches
- ...compatible drive listens enable signal through SMV bus. Enable signal is a software based enable and useful for non-safety related motor stopping in normal ope3 KB (566 words) - 20:13, 28 August 2015
- ...imits", in such case GPO4 will indicate whether axis is within the allowed software configured motion range. ==Electrical interface modes (software selectable)==14 KB (2,244 words) - 20:00, 30 August 2019
- #Disable motor control @ STO2 input (software based)10 KB (1,330 words) - 19:59, 8 December 2021
- ...icient logic voltage or firmware watchdog trigger, drive will now requires software enable command to initialize for safety reasons ...t reporting protocol, with full backwards compatibility. New feature needs software support to become useful, i.e. future Granity version.31 KB (4,414 words) - 12:03, 20 October 2022
- *[[Controller|Motion controller]]. This may be also a software on a computer.2 KB (242 words) - 15:27, 3 December 2015
- ...he link: [http://granitedevices.com/assets/files/granity_setup.exe Granity software] for windows (approx 18 MB) # Launch Granity software and:2 KB (363 words) - 22:06, 19 December 2018
- ...e to D-Sub 25 connector if direct connection to parallel port based PC CNC software is desired5 KB (669 words) - 15:26, 3 December 2015
- ...voltage of capacitors will rise above overvoltage threshold and trigger an software clearable overvoltage fault.3 KB (391 words) - 19:54, 28 August 2015
- Mach4 is a PC CNC controller software that runs on Windows platforms.475 bytes (70 words) - 15:58, 12 January 2018
- [[File:inductance.png|The definition of inductance|thumb]][[Granity]] setup software has a motor resistance and inductance measurement function that works with2 KB (297 words) - 21:55, 1 March 2016
- ...mpleMotion V2]] bus which is used for drive configuration with [[Granity]] software and control over a multidrop capable serial data link. For pinout, see [[Si12 KB (1,829 words) - 09:53, 4 January 2021
- ...e to D-Sub 25 connector if direct connection to parallel port based PC CNC software is desired4 KB (528 words) - 10:18, 24 September 2019
- ...itors will rise above overvoltage threshold ({{param|FOV}}) and trigger an software cleanable overvoltage fault. Overvoltage faults that are caused by returned8 KB (1,288 words) - 21:34, 21 September 2016
- *Software command (via SimpleMotion interface). Can be triggered from configuration t4 KB (611 words) - 19:58, 28 August 2015
- Step 2. Connect to drive with Granity software and inspect status of the HSIN2 from Testing page status information.1 KB (234 words) - 13:49, 2 October 2015
- ...tarting from version 1.9.0, [[Granity]] includes also Linux version of the software. This page lists useful information of installing and using it on different4 KB (553 words) - 13:49, 18 September 2019
- ...hese methods are done on user's own risk. Remember that any malfunction in software or hardware may cause unexpectedly high torque.}}3 KB (552 words) - 10:35, 2 December 2016
- ...that device driver is not installed properly. Try installing ST DfuSeDemo software with drivers to solve the issue. DfuSeDemo Installation Directory will cont3 KB (536 words) - 17:23, 25 November 2018
- # Download [[Granity]] software # Start Granity software8 KB (1,211 words) - 13:09, 28 February 2018
- ** [CEN] Require Software Enable must be turned on in the servo drive settings. Simucube firmware wil ...ffected some imported profiles from files that were exported with previous software versions.51 KB (7,755 words) - 11:41, 15 August 2023
