Difference between revisions of "Argon firmware releases"

• Add STAT_STO_ACTIVE statusbit
• Incremental setpoint change now changes also absolute setpoint readout value

New features:

• Analog in setpoint now has direction input to support 0-10V sources with direction signal (in addition to standard +/-10V)
• New AC/BLDC motor phasing algorithm:
  • Improved operation when axis is heavy to move
  • Phasing now supports limit switches. Now it's possible to use Hall-sensorless phasing when axis lies at the end of travel or if axis is vertical and pulled down by gravity. Requires limit switches on axis and configuring Limit switch functionLFS to other than Do nothing.
• Feature to invert the polarity of motor positive/negative direction. Parameter Invert directionAXI on Granity.
• Improved Dead-time distortion correction giving better servo stiffness

Bug fixes:

• Hall sensor support fixed
• Failure of phasing under high friction fixed
• Toggling of general purpose input lines no longer clear faults in case of clear faults signal is constantly on while other signals change state
• Limit switches now work properly in torque control mode

Adjustments:

• Goal deviation default fault filter time reduced from 0.2 to 0.1 s
• Space vector modulation code cleanup
• Default motor direction is inverted compared to the earlier versions (tick Invert directionAXI to set it same way it was before this version)

A requirement for Granity 1.0.2

Re-tuning may be necessary after upgrade!

• Prevent drive damage in certain conditions (see remarks)
• Activating STO2 now latches a Power stage forced off fault state requiring a clear faults command to return in normal operation

• Fix homing issue when index pulse was enabled (Index pulse searchHMI) and Invert directionAXI was unticked

• New features:
  • Add motor stopping & braking parameters: Dynamic braking decelerationBDD and Mech brake engage delayBED
  • Add Mech brake assisted phasingBAP parameter to assist motor phasing on a vertical axis where gravity pulls axis down. May eliminate Hall sensor requirement on such axis.
  • Motor now returns to the position where it located at the moment of drive power-on (cancel the motion caused by phasing). Works in position & velocity modes.
• Improvements:
  • Optimized torque efficiency on high electrical frequency motors
  • Follow error warning status & digital output now works also in velocity control mode in addition to position mode
  • Improve overcurrent protection setting Over current toleranceFOC consistency
  • Changed the default Over voltage fault thresholdFOV limit value from 350 to 365 VDC to avoid braking resistor heating when idling
• Known bug: Sometimes Initialized state never goes on and also homing won't start in such case. Will be fixed in 1.1.1.

Re-adjusting Over current toleranceFOC may be necessary.

• Fixes & adjustments:
  • Properly always sets Initialized state as true after drive is ready for operation
  • Now motor doesn't rotate to zero position in pulse & direction and quadrature setpoint source modes when Apply is clicked on Granity

• Improvements:
  • Servo control bandwidth increased due to lower position & velocity feedback latency
  • Motion jerks reduced/eliminated while drive is communicating through SimpleMotion V2 bus
• Fixes & adjustments:
  • Corrected "Optimized torque efficiency on high electrical frequency motors" feature functionality of FW package 1.1.0 when Invert directionAXI or Invert feedback directionFBI parameter was set to true.
  • Fix incorrectly displayed torque capture graph polarity when Invert directionAXI was set
  • Over voltage fault thresholdFOV maximum value increased from 375 to 382 VDC

Checking motor tuning recommended after upgrade.

• Improvements:
  • Maximum current limits increased from 10A continuous & 15A peak to 11A continuous & 16A peak
  • Mechanical brake is now released after 0.8 second delay from drive enable or clear faults command to prevent vertixal axis fall before servo control has strength. This delay is adjustable (parameter number 910, value in milliseconds).
• Fixes & adjustments:
  • Fix the issue where enabling Hall sensors may cause reduced torque sensitivity or erratic motion
  • Fix the issue where drive may not complete initialization procedure if Error recovery velocityCRV value is set 0

• New features:
  • Resolver feedback device support, requires Argon resolver adapter
• Fixes & adjustments:
  • Adjusted analog (AIN1, AIN2, CHA, CHB) inputs offset & gain errors closer to zero

• Fixes & adjustments:
  • Fix an issue where Brush DC motor outputs no torque

• New features:
  • "PWM magic trick" to increase maximum effective output voltage of 3 phase AC/BLDC motors by 16%. For more info, see this.
• Fixes & adjustments:
  • Fix a bug causing overcurrent faults in certain conditions
  • Fix pulse&direction setpoint problem with noisy direction signal that may cause drive getting in erroneous direction state

Special versions:

• Fixes & adjustments:
  • Added additional protection interlocks for drive's internal in-rush limiter (reliability improvement)
  • Reduce sensitivity of resolver feedback device no-signal failure (fault location code 890101)
  • Increased upper limit of HV DC bus supply (parameter Over voltage fault thresholdFOV increased)
  • Effectiveness of regenerative resistor improved
  • Speed of Phasing a.k.a. phase search increased
  • Current setpoint during Phasing a.k.a. phase search reduced to reduce unnecessary motor heating during power-on
• Additional changes to Force feedback system (FFB) special version:
  • Eliminate Phasing a.k.a. phase search error in 110-120 VAC power networks
  • Duty cycle limit parameter (6110) now has 200% scale in 110-120 VAC power networks to have equal effect compared to 220-240 VAC networks