Difference between revisions of "SimpleMotion V2 termination with bare cable"
From Granite Devices Knowledge Wiki
| [checked revision] | [checked revision] |
(Created page with "File:multidrop_estop.png|thumb|500px|Typical SM V2 multidrop bus with E-stop functionality. In this page we instruct to eliminate SMV2BRK and connect stop-switch with bare w...") |
|||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[File:multidrop_estop.png|thumb|500px|Typical SM V2 multidrop bus with E-stop functionality. In this page we instruct to eliminate SMV2BRK and connect stop-switch with bare wires.]] | [[File:multidrop_estop.png|thumb|500px|Typical SM V2 multidrop bus with E-stop functionality. In this page we instruct to eliminate SMV2BRK and connect stop-switch with bare wires.]] | ||
[[File:Ethernet_RJ45_connector_p1160054.jpg|thumb|RJ45 cable compatible with Ethernet and SimpleMotion V2]] | [[File:Ethernet_RJ45_connector_p1160054.jpg|thumb|RJ45 cable compatible with Ethernet and SimpleMotion V2]] | ||
| − | [[SimpleMotion V2]] communication link and [[Argon (servo drive)|Argon]] drives use [http://en.wikipedia.org/wiki/Modular_connector#8P8C RJ45] connectors and cables as physical connection standard. | + | [[SimpleMotion V2]] communication link and [[Argon (servo drive)|Argon]] and [[IONI]] drives use [http://en.wikipedia.org/wiki/Modular_connector#8P8C RJ45] connectors and cables as physical connection standard. |
| − | While the preferred way to terminate [[SimpleMotion V2]] bus is to use [[SMV2BRK]] break-out-board, there is also an option to do it with bare RJ45 Ethernet cable. This page instructs how to achieve proper termination. | + | While the preferred way to terminate [[SimpleMotion V2]] bus is to use [[SMV2BRK]] break-out-board or [[IONICUBE]]/[[IONICUBE 1X]] devices, there is also an option to do it with bare RJ45 Ethernet cable. This page instructs how to achieve proper termination. |
| − | + | Before proceeding, make sure you understand [[SimpleMotion V2 port]]. | |
| − | + | ||
| − | + | ||
==Use as E-stop & Enable input== | ==Use as E-stop & Enable input== | ||
| − | In Argon drive, the same connector acts also as | + | In Argon drive, the same connector acts also as emergency stop or [[Safe torque off]] input. User may connect a e-stop button directly at the end of device chain to gain reliable stopping mechanism for all linked devices. |
==Wiring with bare RJ45 cable== | ==Wiring with bare RJ45 cable== | ||
| + | {{damage|Pay extra attention to correct wiring in this section. Miswiring or usage of wrong type RJ45 cable (using cross-over cable instead of straight cable) are the most common reasons for damaged drives.}} | ||
[[File:Rj45 estop and enable.png|thumb|E-stop and enable signal wiring to RJ45 cable]] | [[File:Rj45 estop and enable.png|thumb|E-stop and enable signal wiring to RJ45 cable]] | ||
[[File:smv2_enablequickndirty.jpg|thumb|A quick'n'dirty way to make enable drive & disable [[safe torque off]] connection. May be used for testing before final wiring.]] | [[File:smv2_enablequickndirty.jpg|thumb|A quick'n'dirty way to make enable drive & disable [[safe torque off]] connection. May be used for testing before final wiring.]] | ||
| Line 45: | Line 44: | ||
[[Category:SimpleMotion]] | [[Category:SimpleMotion]] | ||
[[Category:Argon wiring]] | [[Category:Argon wiring]] | ||
| − | [[Category: | + | [[Category:IONI wiring]] |
Latest revision as of 09:23, 19 May 2015
SimpleMotion V2 communication link and Argon and IONI drives use RJ45 connectors and cables as physical connection standard. While the preferred way to terminate SimpleMotion V2 bus is to use SMV2BRK break-out-board or IONICUBE/IONICUBE 1X devices, there is also an option to do it with bare RJ45 Ethernet cable. This page instructs how to achieve proper termination.
Before proceeding, make sure you understand SimpleMotion V2 port.
Use as E-stop & Enable input[edit | edit source]
In Argon drive, the same connector acts also as emergency stop or Safe torque off input. User may connect a e-stop button directly at the end of device chain to gain reliable stopping mechanism for all linked devices.
Wiring with bare RJ45 cable[edit | edit source]
 | Pay extra attention to correct wiring in this section. Miswiring or usage of wrong type RJ45 cable (using cross-over cable instead of straight cable) are the most common reasons for damaged drives. |
A quick'n'dirty way to make enable drive & disable safe torque off connection. May be used for testing before final wiring.
| SimpleMotion V2 devices use pins 3, 6 and 8 (RS485_A,RS485_B and GND) for serial communication. If something interferes these lines, communication may fail or devices may be damaged. Before powering 24V to any of the pins, ensure that pins 3 and 6 are not connected to any external circuit. It's also highly recommended to use current limited 24V power source for initial tests to reduce risk of damage (0.15-0.3A limit). |
Connector pinout[edit | edit source]
| Pin # | Signal name | Description | Electrical wiring |
|---|---|---|---|
| 1 | STO2_24V | STO input 2 | Supply 24VDC in this pin referenced to GND to disable STO2. 1 |
| 2 | Reserved | Reserved for future use | Do not connect |
| 3 | RS485_A | RS485 signal A | RJ45 cable routes this between devices and SimpleMotion V2 USB adapter |
| 4 | STO1_24V | STO input 1 24V in | Supply 24VDC between STO1_24V and STO1_0V to disable STO1. STO1 inputs are floating and isolated from GND. 1, 2 |
| 5 | STO1_0V | STO input 1 0V in | |
| 6 | RS485_B | RS485 signal B | RJ45 cable routes this between devices and SimpleMotion V2 USB adapter |
| 7 | ENABLE_IN_24V | Drive enable control signal | Supply 24VDC in this pin referenced to GND to set drive in enabled state. |
| 8 | GND | Ground reference for: RS485, STO2 and ENABLE_IN | RJ45 cable routes this between devices and SimpleMotion V2 USB adapter. For enable & STO connect this to external 24V power supply ground. |
1) STO1 and STO2 are controlling two independent Safe torque off methods. Both must be supplied 24V simultaneously to enable torque to the motor.
2) STO1 has limited functionality on Argon if HV DC bus is shared between drives or external DC voltage is supplied. For more info, see Argon user guide/J4 connector wiring.
| Even when RJ45 connector and cables are being used in Ethernet and SimpleMotion, these protocols are not electrically compatible. Never connect SimpleMotion device to Ethernet device. |
